• The KSFM Journal of Fluid Machinery
• /
• v.7 no.1 s.22
• /
• pp.45-50
• /
• 2004

Two phenomena often encountered in liquid flow, which were completely absent in gas or vapor flow, were cavitation and flashing. These phenomena were of significant interest in any comprehensive discussion of control valves or contracted devices since their occurrence would affect the device sizing procedures, might introduce noise and vibration, and also may limit the life expectancy of device components and the immediate downstream piping. Thus, this study aimed to find the reduction method of occurred cavitation in system by the computer simulation. A derivative six model with different dimensions of cavity were adopted. From the results, it was found that the length of the cavity was mote important factor to reduce the pressure drop over the control valves or contracted devices than the depth of the cavity. And the pressures along the centerline of the contracted devices were dropped two times in the case of haying the large length (Lc=1.5D) of cavity.

• Proceedings of the IEEK Conference
• /
• summer
• /
• pp.218-220
• /
• 2004

A new wide-band VCO topology using Miller capacitance is proposed. Contrary to conventional VCO using the Miller capacitance where the variable amplifier gain is negative, the proposed VCO uses both the negative and positive variable amplifier gain to enhance the frequency tuning range significantly. The proposed VCO is simulated using HSPICE. The simulations show that 410MHz and 220MHz frequency tuning range are obtained using the negative .and positive variable amplifier gain, respectively. The tuning range of the proposed VCO is $23\%$ of the center frequency(2.8GHz). The phase noise is -104dBc/Hz at 1MHz offset by simple model. The operating current is only 3.84mA at 2.5V power supply.

• Korean Journal of Optics and Photonics
• /
• v.9 no.5
• /
• pp.348-352
• /
• 1998

By employing the Berreman's backflow model, we investigated the effect of liquid crystal parameters on the optical switching characteristics of a bistable twisted-nematic liquid crystal cell. We found that d/p is the most important parameter for high speed operation.

• Proceedings of the Korean Society for Information Management Conference
• /
• 2013.08a
• /
• pp.101-104
• /
• 2013

본 연구에서는 웹 환경에 적합한 서지 기술을 위해 LC에서 개발한 BIBFRAME을 분석하고, BIBFRAME이 개방형 서지 데이터의 생성에 적합한지를 검토하였다. 그리고 BIBFRAME의 등장 배경 및 특징을 FRBR 모형과 비교하였다. 그 결과 BIBRAME은 1)서지 객체의 지적 내용과 물리 매체를 구분하고 있었는데, FRBR의 제1그룹보다 단순한 구조를 지니고 있었다. 2) 인명전거와 주제전거를 포함하는 넓은 개념으로 전거를 정의하고 있었으며, 서지데이터 작성자의 관점과 이용자의 관점을 함께 고려하였다. 3) 다양한 외부 데이터와의 연계 및 개별 도서관에 특화된 데이터를 추가할 수 있는 주석 개념을 도입하였다. BIBFRAME은 MARC 레코드에서 변환하거나 직접적으로 서지데이터를 작성하는 방안이 모두 가능하며, 웹 환경에 적합하다고 판단된다.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.7
• /
• pp.376-383
• /
• 1999

The piezoelectric transformer (PT) is an electro-mechanical device that transfers electrical energy through a mechanical vibration. In this paper, a PT operating in the contour vibration mode is introduced for an application of fluorescent lamp ballast. Utilizing its inherent characteristics of the LC resonator and a high voltage gain to ignite the lamp in light load condition, an investigation of a power piezoelectric transformer as a potential component for a fluorescent lamp ballast is discussed. PT is easy to be produced in mass and reduces the cost of the ballast. The modified equivalent circuit model of the PT considering the operating current level is derived to design the fluorescent lamp ballast. This model describes the voltage gain of the PT in wide load variations and various input current levels. The experimental and simulation results are provided to verify theoretical analysis. The power capacity of the currently developed PT is relatively low (15W), but it can be increased by adopting a multi-layer structure and is currently under investigation. It is also possible to parallel the PT for higher power processing.

• Environmental Analysis Health and Toxicology
• /
• v.16 no.3
• /
• pp.133-137
• /
• 2001

Acetanilide is a High Production Volume Chemical, which is produced about 2,300 tons/year in Korea as of 1998 survey. Most is used as an intermediate for synthesis of pharmaceuticals and dyes and the chemical is one of seven chemicals of which human and environmental risks are being assessed by National Institute of Environmental Research under the frame of OECD SIDS program. The chemical is water soluble (4 g/1 at 20$\^{C}$) and readily biodegradable (68.7％). Partition coefficiency (Log Pow) is 1.16 at 23$\^{C}$ so that the chemical has a low potential for bioaccumulation. The acute toxicities of algae, daphnia and fish are not high. The 72 hr-EｂC50 of algae is 13.5 mg/1,48 hr-EC50 of daphnia is over 100 mg/1 and 96 hr-LC50 of Oryzias latipes is over 100mg/1. Regarding the exposure, levels in air, water, soil or sediment have not been monitored or estimated so that risk evaluation of acetanilide was not possible. In this study, distribution of the chemical among environmental media was estimated using EQC model based on the chemical-physical properties. In Level I and IIof which the chemical are hypothesized in equilibrium and no transfer through the media, more than 98％ of acetanilide are estimated to be distributed in water. However, in Level Ⅲ of which non-equilibrium and intermedia transfer could be occurred, the chemical is estimated to distributed to soil as 51.8％ and water as 47.8％ as of total amount.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.5
• /
• pp.437-444
• /
• 2015

In simulation-based circuit optimization, many simulation runs may be wasted while evaluating infeasible designs, i.e. the designs that do not meet the constraints. To avoid such a waste, this paper investigates the use of support vector machine (SVM) classifiers in predicting the design's feasibility prior to simulation and the optimal selection of the SVM parameters, namely, the Gaussian kernel shape parameter ${\gamma}$ and the misclassification penalty parameter C. These parameters affect the complexity as well as the accuracy of the model that SVM represents. For instance, the higher ${\gamma}$ is good for detailed modeling and the higher C is good for rejecting noise in the training set. However, our empirical study shows that a low ${\gamma}$ value is preferable due to the high spatial correlation among the circuit design candidates while C has negligible impacts due to the smooth and clean constraint boundaries of most circuit designs. The experimental results with an LC-tank oscillator example show that an optimal selection of these parameters can improve the prediction accuracy from 80 to 98% and model complexity by $10{\times}$.

• Fibers and Polymers
• /
• v.2 no.2
• /
• pp.86-91
• /
• 2001

Liquid crystalline (LC) poly(ethylene terephthalate-co-2(3)-chloro-1,4-phenylene terephthalate) [copoly(ET/CPT)] was prepared using poly(ethylene terephthalate) (PET) as a flexible spacer, terephthalic acid (TPA), and chlorohydroquinone diacetate (CHQDA). All reactions involved in the copolymerization were investigated using some model compounds: TAP was used for acidolysis, diphenylethyl terephthalate (DPET) for interchange reaction between PET chains, and 야-o-chlorophenyl terephthalate (DOCT) and di-m-chlorophenyl terephthalate (DMCT) for interchange reaction between PET and rigid rodlike segments. Activation energies obtained for the acidolysis of PET with TPA and for interchange reaction of PET with DPET, DOCT, and DMCT were 19.8 kcal/mol, 26.5 kcal/mole, and 45.9 kcal/mole, respectively. This result supports that the copolymerization proceeds through the acidolysis of PET with TPA first and subsequent polycondensation between carboxyl end group and CHQDA or acetyl end group, which is formed from the reaction of CHQDA and TPA. Also, it was found that ester-interchange reaction can be influenced by the steric hindrance. Copoly(ET/CPT)s obtained has ethylene acetate end groups formed from acetic acid hydroxy ethylene end groups and showed almost the random sequence distribution for all compositions.

• Applied Microscopy
• /
• v.42 no.4
• /
• pp.179-185
• /
• 2012

Alzheimer's disease (AD) is a progressive neurodegenerative disorder. Neuropathological hallmarks of AD are amyloid plaques, dystrophic neurite, and alteration of subcellular organelles. However, the morpho-functional study of this degenerative process and ultimate neuronal death remains poorly elucidated. In this study, immunohistochemical and ultrastructural analyses were performed to clarify the abnormal morphological alterations caused by the progression of AD in APP/PSEN1 transgenic mice, express human amyloid precursor protein, as a model for AD. In transgenic AD mice brain, the accumulation of Amyloid ${\beta}$ plaques and well-developed dystrophic neurites containing anti-LC3 antibody-positive autophagosomes were detected in the hippocampus and cortex regions. We also found severe disruption of mitochondrial cristae using high-voltage electron microscopy and three-dimensional electron tomography (3D tomography). These results provide morpho-functional evidence on the alteration of subcellular organelles in AD and may help in the investigation of the pathogenesis of AD.

• Transactions of the Society of Information Storage Systems
• /
• v.5 no.2
• /
• pp.82-88
• /
• 2009

Understanding the adhesion behavior and characteristics of toner film is required to achieve image and text printing with high quality resolution. Toner can be considered as a thin film coating on a media such as paper or polymer film. Quantitative measurement of adhesion characteristics of the thin film is important to assess the reliability of the system. In this work the main objective was to investigate the adhesion characteristic between the toner and the media by ramp loading scratch test method. The scratch test may be used to obtain quantitative information about the adhesion of the film to the substrate. In the scratch test a diamond tip was used to scratch the surface of the toner film under an increasing normal load until the toner detached or fractured. The critical load (LC) was obtained from the experimental results. Also, the relationship between the critical load and the adhesive strength of the interface between the substrate and the toner was obtained by measuring the normal and tangential forces during the scratch test. Finally, theoretical analysis of the toner scratch characteristics was performed based on Benjamin and Weaver theory, Plowing model, and Laugier model.