• 한국초전도ㆍ저온공학회논문지
• /
• 제23권3호
• /
• pp.51-54
• /
• 2021

The DC system has less power loss compared to the AC system because there is no influence of frequency and dielectric loss. However, the zero-crossing point of the current is not detected in the event of a short circuit fault, and it is difficult to interruption due to the large fault current that occurs during the opening, so the reliability of the DC breaker is required. As a solution to this, an LC resonance DC circuit breaker combined a superconducting element has been proposed. This is a method of limiting the fault current, which rises rapidly in case of a short circuit fault, with the quench resistance of the superconducting element, and interruption the fault current passing through the zero-crossing point through LC resonance. The superconducting current limiting element combined to the DC circuit breaker plays an important role in reducing the electrical burden of the circuit breaker. However, at the beginning of a short circuit fault, superconducting devices also have a large electrical burden due to large fault currents, which can destroy the element. In this paper, the reactor is connected to the source side of the circuit using PSCAD/EMTDC. After that, the change of the fault current according to the reactor capacity and the electrical burden of the superconducting element were confirmed through simulation. As a result, it was confirmed that the interruption time was delayed as the capacity of the reactor connected to the source side increased, but peak of the fault current decreased, the zero-crossing point generation time was shortened, and the electrical burden of the superconducting element decreased.

• 정보통신설비학회논문지
• /
• 제9권4호
• /
• pp.153-157
• /
• 2010

In this paper, a dual band LNA (Low Noise Amplifier) with a LC-tank matching circuit is designed for 912MHz and 2.45GHz RFID reader. The operating frequency is decided by the LC-tank resonance. The simulated results demonstrate that S21 parameter is 11.683dB and 5.748dB at 912MHz and 2.45GHz, respectively, and the S11 are -10.796dB and -21.261dB, the S22 are -7.131dB and -14.877dB at the same frequencies. The measured NF (Noise Figure) is 0.471 and 1.726 at 912MHz and 2.45GHz, respectively.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 C
• /
• pp.1872-1874
• /
• 2001

This paper presents an implantable telemetry LC resonance-type pressure sensor to measure the cerebral ventricle pressure. The sensor consists of an inductor and a capacitor. The LC resonant circuit consists of the sensor and an external antenna coil that are coupled magnetically. The resonance frequency of the circuit decreases as the applied pressure increases the capacitance of the sensor. The sensor is designed in consideration of the biocompatibility and long lifetime for continuous monitoring of the ventricle pressure. The sensor is simple to fabricate and small in comparison with others reported previously. The inductor is fabricated by electroplating and the variable capacitor is constructed with a flexible p+ diaphragm. Also, the deflection of the diaphragm, the variation of the capacitance and the resonance frequency are analyzed and calculated.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2016년도 전력전자학술대회 논문집
• /
• pp.323-324
• /
• 2016

In this paper a high efficiency bidirectional resonant converterfor Vehicle-to-Grid applications (V2G) is proposed.The proposed converter has adopted an LC auxiliary circuit in the third winding of the transformer. With the proposed method full softswitching can be ensured in all switches over a wide range of loadsand the secondary ringing can be removed with no additional snubber or clamp circuitry.In addition, since the proposed resonant converter is able to operate at an almost constant resonant frequencyregardless of the load, CC/CV charge of the battery can be simply implemented with high efficiency. A 3.3 kW bidirectional converter for On-Board Charger of Electric Vehicle is implemented to verify the validity of the proposed method. The experimental results show the high efficiency characteristics of the proposed converter over the wide range of load in both charge and discharge mode. The maximum efficiency of the proposed system was 98.13 % at 2.3 kW during the constant voltage mode charge operation.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.300-302
• /
• 2003

Fluorescent lamp converts electrical energy Into light energy. Generally we use both electronic ballast and glow starter method in the house. We developed 40W electronic starter and its characteristic is verified by experiments. The efficiency of ballast is improved by using the LC Parallel reasonance circuit at input stage and LC series reasonance circuit at out-put stage.

• 한국통신학회논문지
• /
• 제22권2호
• /
• pp.318-324
• /
• 1997

Chua 회로는 간단한 전기 및 전자 회로를 구성하여 카오스 현상을 나타내는 회로로 자율, 3차계, 가역성(Reciprocal)이며 1개의 비션형 소자인 3구분 선형 저항과 4개의 선형 소자인 (R, L, $C_1,\;C_2$)로 구성되는 발진회로이다. 본 논문에서는 Chua 회로의 병렬 LC 공진기를 단락하여 시간 지연을 갖는 무손실 전송선로로 치환하고 특성 곡선법을 써서 파라미터 변화에 의한 카오스 운동과 주기운동이 있음을 위상공간과 분기도(Bifurcation diagram)로 확인 하였으며 무손실 전송선로가 원래의 Chua 회로와 유사한 어트렉터가 존재함을 확인하였다.

• 한국산학기술학회논문지
• /
• 제20권3호
• /
• pp.491-499
• /
• 2019

최근에, 전원 공급 장치에 있어서 파워의 품질에 대한 요구가 높아지고 있다. IEC 61000-3-2 규격은 조명을 위한 AC/DC 전원 공급 장치에 대하여 역률(PF)과 전체 파형 왜곡률(THD)에 대한 규격을 만족하도록 요구하고 있다. 또 출력단의 전류 변화에 의해 발광체 광량이 바뀜에 따라 발생되는 플리커 현상에 대해 유럽권 선진국가는 ripple rate의 기준을 15~30%로 설정해 규제하고 있다. 따라서 국내에서도 기준을 마련하고 규제를 추진 중에 있다. 그래서 본 논문은 PFC 규격을 만족하고, 회로 1차, 2차 간 절연 기능을 가지기 위해 Flyback 컨버터를 적용하며, LED 전류의 저주파 리플을 저감하기 위해 Flyback, Coupled Inductor, LC 병렬 공진 필터, LLC 공진 필터, Cuk을 이용한 각각의 LED 구동회로를 PSIM을 통해 시뮬레이션 함으로써 각각의 방식들을 비교하였으며, 출력측 리플 저감을 위해 1차측에 Coupled Inductor와 2차측에 LC 공진을 적용한 Coupled LC 공진 회로를 제안하였으며, Coupled LC 공진 방식은 출력 커패시터가 78uF으로 작으며, 출력 리플은 전압 2.38V, 전류 0.05A로 기존의 방식보다 22%의 출력 리플 저감을 확인 하였다.

• 전력전자학회논문지
• /
• 제4권2호
• /
• pp.122-127
• /
• 1999

본 논문에서는 3마력의 컴프레샤 모터를 갖는 대용량의 인버터 에어컨의 원가절감과 성능향상을 위해서 병렬구동방식을 사용한 역률제어회로를 제안하였다. 역률개선 LC필터를 제거하고 출력캐패시터와 인버터 스위치의 정격축소를 통해서 재료비를 줄이기 위해서 적절한 설계절차를 제시하였다. 이렇게 결정된 소자를 사용하여 6[kW] 소지전력을 갖는 프로토형 회로를 구성하고 제안된 회로의 동작을 확인하기 위해서 실험을 하였다.

• 전기학회논문지
• /
• 제67권12호
• /
• pp.1611-1618
• /
• 2018

This paper proposes a new auxiliary resonant commutated pole (ARCP) inverter which has a modified auxiliary circuit. The proposed auxiliary circuit includes two auxiliary IGBT switches, an LC resonant circuit, and two clamping diodes. In order to analyze the performance of proposed ARCP inverter, computer simulations with PSCAD, and hardware experiments were carried out. Through analyzing the experimental results, it is known that the proposed ARCP inverter offers efficiency improvement of 1.5% compared with the hard-switching inverter.

• 조명전기설비학회논문지
• /
• 제18권5호
• /
• pp.27-34
• /
• 2004

본 논문에서는 half-bridge inverter를 이용하여 400[W] 고압나트륨 램프용 전자식 안정기를 설계하였다. 제안된 등가 LC 직렬 공진회로에서 인덕터와 커패시터의 값을 이론적으로 계산하고, LC 직렬 half-bridge 회로에 대한 IsSPICE 시뮬레이션을 수행하였다. 계산결과를 검증하기 위해 전자식 안정기를 설계 제작하여 실험을 수행하였다. 실험에 의한 전자식 안정기의 제반특성은 시뮬레이션 결과와 대단히 유사하였다. 실험결과 출력전압 400[W]에서 역률 99.3[%], 전류 전고조파 10.01[%], 램프효율 119[lm/W]의 좋은 성과를 나타내었다.