• 한국지진공학회논문집
• /
• 제13권5호
• /
• pp.23-29
• /
• 2009

1996년 12월 13일 강원도 영월군 지역에서 국지규모(M$_L$) 4.5의 지진이 발생하였다. 진앙은 37.2545$^{\circ}$N, 128.7277$^{\circ}$E이며, 지체구조구상 옥천습곡대에 해당한다. 지진자료의 필터링 대역에 따라 파형역산을 수행하였는데, 0.02$\sim$0.2 Hz 필터링 대역을 적용할 경우 진원 깊이는 6 km, 지진모멘트는 1.3$\times$10$^{16}$ N$\cdot$m로 추정되었다. 이 지진모멘트는 모멘트규모(M$_W$) 4.7에 해당한다. 파형역산과 P파의 초동 극성 분석을 통한 영월 지진의 발진기구는 역단층 성분을 포함한 주향이동단층 특성을 보이며, 주응력 방향은 동북동-서남서 방향이다. 스펙트럼 분석을 통해 추정된 모멘트규모는 4.8이며, 이는 파형역산에 의해 추정된 모멘트규모와 비슷하다. 평균 응력강하는 14.3 MPa로 추정되었다.

• 한국농공학회지
• /
• 제44권5호
• /
• pp.41-53
• /
• 2002

This study was conducted to derive the regional design rainfall by the regional frequency analysis based on the regionalization of the precipitation suggested by the first report of this project. According to the regions and consecutive durations, optimal design rainfalls were derived by the regional frequency analysis for L-moment in the second report of this project. Using the LH-moment ratios and Kolmogorov-Smirnov test, the optimal regional probability distribution was identified to be the Generalized extreme value (GEV) distribution among applied distributions. regional and at-site parameters of the GEV distribution were estimated by the linear combination of the higher probability weighted moments, LH-moment. Design rainfall using LH-moments following the consecutive duration were derived by the regional and at-site analysis using the observed and simulated data resulted from Monte Carlo techniques. Relative root-mean-square error (RRMSE), relative bias (RBIAS) and relative reduction (RR) in RRMSE for the design rainfall were computed and compared in the regional and at-site frequency analysis. Consequently, it was shown that the regional analysis can substantially more reduce the RRMSE, RBIAS and RR in RRMSE than at-site analysis in the prediction of design rainfall. Relative efficiency (RE) for an optimal order of L-moments was also computed by the methods of L, L1, L2, L3 and L4-moments for GEV distribution. It was found that the method of L-moments is more effective than the others for getting optimal design rainfall according to the regions and consecutive durations in the regional frequency analysis. Diagrams for the design rainfall derived by the regional frequency analysis using L-moments were drawn according to the regions and consecutive durations by GIS techniques.

• 대한치과교정학회지
• /
• 제29권5호
• /
• pp.511-519
• /
• 1999

생역학적으로 우수한 스프링을 설계하기 위해서 스프링의 형태에 여러 가지 변화를 주면서 각 상황에서 force system이 변하는 양상을 수치분석계산과 spring tester를 이용한 실험과 비교하였다. 주어진 해부학적인 한계 내에서 최대한 생역학적 효율을 높이는 요소들을 제시하였다. 1. 스프링의 높이가 증가하면 M/F ratio는 증가하고 L/D rate은 감소한다. 2. 스프링의 최소 굽힘 모멘트 부위보다 위에 wire를 첨가하면 M/F ratio는 증가하고 L/D rate은 감소한다. 3. 스프링의 최소 굽힘 모멘트 부위보다 아래에 wire를 첨가하면 M/F ratio는 감소하고 L/D rate도 감소한다. 4. 스프링의 위쪽에 아무리 wire를 많이 첨가하여도 스프링의 높이 이상의 M/F ratio는 얻을 수 없다. 5. 제한된 높이의 스프링으로 충분한 M/F ratio를 얻기 위해서는 부가적인 모멘트가 필요하다. 6. 스프링의 수평 길이가 증가할 수록 M/F ratio와 L/D rate는 감소하므로 부가적인 모멘트는 점점 각도가 증가할 수 있도록 스프링 전체에 부여할 필요가 있다. 7. L/D rate는 재료, 단면, 그리고 형태에 영향을 받지만 M/F ratio는 재료나 단면에 관계없이 스프링의 형태에만 영향을 받는다.

• 대한조선학회지
• /
• 제7권1호
• /
• pp.37-44
• /
• 1970

The plate under shear loading umformly distributed on the end portions of its side boundary was considered. Infinite hyperbolic serieses and Fourier serieses were combined as a stress function and from which exact solutions for the 15 cases for the parameters of b/L=0.25, 0.5, 1.0 and l/L=0.2, 0.4, 0.6, 0.8, 1.0 are obtained. In each cases the first 5 terms of the infinite series at the 36 points as shown in Fig. 3. The results are presented in Fig. 4-1, 4-2, and 4-3. The conclusions are as follows: 1) The stresses ${\sigma}_x$ increase very slightly as $\chi$ increases in the range of 0<x<L-l 2) When the parameters satisfy the conditions b/L<0.25 and l/L<0.2, the stresses in the region of 0<x<L-l can be obtained by replacing the uniform shear loading by the equivalent uniform shear loading by the equivalent uniform tensile force and pure bending moment at x=l. 3) The stress ${\sigma}_y$ is negligible throughout the region. 4) When the parameter b/L varies, the stresses ${\sigma}_x$ and u vary as L/b, while strain $\upsilon$ varies as $(L/b)^2$.

• 한국농공학회지
• /
• 제40권4호
• /
• pp.45-57
• /
• 1998

This study was conducted to derive optimal design floods by Generalized Extreme Value (GEV) distribution for the annual maximum series at ten watersheds along Han, Nagdong, Geum, Yeongsan and Seomjin river systems. Adequacy for the analysis of flood data used in this study was established by the tests of Independence, Homogeneity, detection of Outliers. L-coefficient of variation, L-skewness and L-kurtosis were calculated by L-moment ratio respectively. Parameters were estimated by the Methods of Moments and L-Moments. Design floods obtained by Methods of Moments and L-Moments using different methods for plotting positions in GEV distribution were compared by the Relative Mean Errors(RME) and Relative Absolute Errors(RAE). The results were analyzed and summarized as follows. 1. Adequacy for the analysis of flood data was acknowledged by the tests of Independence, Homogeneity and detection of Outliers. 2. GEV distribution used in this study was found to be more suitable one than Pearson type 3 distribution by the goodness of fit test using Kolmogorov-Smirnov test and L-Moment ratios diagram in the applied watersheds. 3. Parameters for GEV distribution were estimated using Methods of Moments and L-Moments. 4. Design floods were calculated by Methods of Moments and L-Moments in GEV distribution. 5. It was found that design floods derived by the method of L-Moments using Weibull plotting position formula in GEV distribution are much closer to those of the observed data in comparison with those obtained by method of moments using different formulas for plotting positions from the viewpoint of Relative Mean Errors and Relative Absolute Errors.

• 대한의용생체공학회:의공학회지
• /
• 제27권5호
• /
• pp.210-217
• /
• 2006

Many types of interspinous distraction devices (IDDs) have been recently developed as an alternative surgical treatment to laminectomy and fusion with pedicle screws for the treatment of the lumbar spinal stenosis (LSS). They are intended to keep the lumbar spine in a slightly flexed posture to relieve pain caused by narrowing of the spinal canal and vertebral foramen. However, their biomechanical efficacies are not well known. In this study, we evaluated the kinematic behaviors and changes in intradiscal pressure (IDP) of the porcine lumbar spine implanted with IDD. For kinematics analysis, five porcine lumbar spines (L2-L6) were used and the IDD was inserted at L4-L5. Three markers (${\phi}{\le}0.8mm$) were attached on each vertebra to define a rigid body motion for stereophotogrammetric assessment of the spinal motion in 3-D. A moment of 7.5Nm in flexion-extension, lateral bending, and axial rotation were imparted with a compressive force of 700N. Then, IDD was implanted at L3-L4. IDPs were measured using pressure transducer under compression (700N) and additional extension moment (700N+7.5Nm). In kinematic behaviors, insertion of IDD resulted in statistically significant decrease 42.8% at the implanted level in extension. There were considerable changes in ROM at the adjacent levels, but statistically insignificant. In other motions, there were no significant changes in ROM as well regardless of levels. IDPs at the surgical level (L3-L4) under compression and extension moment decreased by 12.9% and 18.8% respectively after surgery (p<0.05). At the superiorly adjacent levels, IDPs increased by 19.4% and 12.9% under compression and extension, respectively (p<0.05). Corresponding changes at the inferiorly adjacent levels were 29.4% and 6.9%, but they were statistically insignificant (p>0.05). The magnitude of pressure changes due to IDD, both at the operated and adjacent levels, were far less than the previously reported values with conventional fusion techniques. Our experimental results demonstrated the IDDs can be very effective in limiting the extension motion that may cause narrowing of the spinal canal and vertebral foramens while maintaining kinematic behaviors and disc pressures at the adjacent levels.

• 한국농공학회논문집
• /
• 제46권5호
• /
• pp.27-39
• /
• 2004

In the first part of this study, five homogeneous regions in view of topographical and geographically homogeneous aspects except Jeju and Ulreung islands in Korea were accomplished by K-means clustering method. A total of 57 rain gauges were used for the regional frequency analysis with minimum rainfall series for the consecutive durations. Generalized Extreme Value distribution was confirmed as an optimal one among applied distributions. Drought rainfalls following the return periods were estimated by at-site and regional frequency analysis using L-moments method. It was confirmed that the design drought rainfalls estimated by the regional frequency analysis were shown to be more appropriate than those by the at-site frequency analysis. In the second part of this study, LH-moment ratio diagram and the Kolmogorov-Smirnov test on the Gumbel (GUM), Generalized Extreme Value (GEV), Generalized Logistic (GLO) and Generalized Pareto (GPA) distributions were accomplished to get optimal probability distribution. Design drought rainfalls were estimated by both at-site and regional frequency analysis using LH-moments and GEV distribution, which was confirmed as an optimal one among applied distributions. Design rainfalls were estimated by at-site and regional frequency analysis using LH-moments, the observed and simulated data resulted from Monte Carlotechniques. Design drought rainfalls derived by regional frequency analysis using L1, L2, L3 and L4-moments (LH-moments) method have shown higher reliability than those of at-site frequency analysis in view of RRMSE (Relative Root-Mean-Square Error), RBIAS (Relative Bias) and RR (Relative Reduction) for the estimated design drought rainfalls. Relative efficiency were calculated for the judgment of relative merits and demerits for the design drought rainfalls derived by regional frequency analysis using L-moments and L1, L2, L3 and L4-moments applied in the first report and second report of this study, respectively. Consequently, design drought rainfalls derived by regional frequency analysis using L-moments were shown as more reliable than those using LH-moments. Finally, design drought rainfalls for the classified five homogeneous regions following the various consecutive durations were derived by regional frequency analysis using L-moments, which was confirmed as a more reliable method through this study. Maps for the design drought rainfalls for the classified five homogeneous regions following the various consecutive durations were accomplished by the method of inverse distance weight and Arc-View, which is one of GIS techniques.

• 한국산학기술학회논문지
• /
• 제10권5호
• /
• pp.1009-1019
• /
• 2009

본 연구에서는 우리나라 수위관측소들 중에서 관측 유량이 검증된 총 19개 유역을 선정하고 관측된 홍수량을 사용하여 적정 설계홍수량을 유도함으로써 우리나라의 설계홍수량 특성을 분석하였다. 대상유역별로 관측개시 년도에서부터 분석 시작년을 기준으로 1년씩 증가 시키는 점진적 구성 방식으로 연최대홍수량에 대한 빈도분석을 실시하기 위해, 변동특성을 이동평균법에 의해 분석하였다. 19개 대상유역에 대한 연최대홍수량 계열 구성기간별로 기본통치를 산정하고 독립성, 동질성 및 Outiler 검정을 실시하였다. Gumbel, Generalized Extreme Value, Generalized Logistic 및 Generalized Pareto 분포의 적합도 검정을 LH-모멘트비도와 Kolmogorov-Smirnov 검정에 의해 수행하였다. 적정 확률분포로 선정된 GEV 분포의 매개변수를 확률가중모멘트의 치수 변화에 의한 L, L1, L2, L3 및 L4-모멘트법에 의해 추정하고 대상유역 및 연최대홍수량 계열 구성 기간별 설계홍수량을 유도하였다. 본 연구에서 사용한 변동률 분석에 따라 최근 지구온난화에 따른 우리나라 기후 변화를 고려한 적절한 수리구조물의 설계 조건변경시기는 2002년 전후로 하여야 할 것이다.

• 한국작물학회지
• /
• 제36권4호
• /
• pp.319-323
• /
• 1991

벼의 도복에 관련하는 형질들의 포장도복과의 관련정도를 밝혀 벼의 이도복성육종의 기초자료를 제공코져 1900년대에서 1980년대에 재배 또는 육성된 10품종을 재배하여 실험한 결과를 요약하면 다음과 같다. 1 포장도복정도와 관련정도가 높은 형질들은 간장, 단위간하중(W/l), 단위 직경휨모멘트(W1/d), 도복지수(L), 하중비(W1/P), 임계도 복하중지수 (Ws$^2$/l$^4$)등 이었다. 2. 간장은 포장도복과 높은 상관(r=0.7607)을 보이나 간장만으로 품종의 도복정도를 판정하기는 미흡하였다 3. 측정의 난역도와 소모되는 시간을 고찰해 볼 때 도복저항성을 판정하는데 유용할 형질들은 간장, W/l, W1/d, Ws$^2$/l$^4$이었다. 4. 간경, 줄기단면적, 간벽의 두께, 줄기단면의 2차 관성 모멘트는 포장도복과 아무런 상관관계를 보이지 않았다. 5. 좌절강도(S)는 포장도복과 유의한 부의 상관 (r=-0.3986)을 보였다.

• Korean Chemical Engineering Research
• /
• 제54권4호
• /
• pp.487-493
• /
• 2016

양이온교환 고성능액체크로마토그래피에서 라이소자임을 분석하고, 실험결과인 크로마토그램을 통해 모멘트 분석을 수행하였다. 용리 인산완충용액은 1.0, 0.75, 0.5 M의 소금을 포함하였다. 실험변수는 유량, 용리 완충용액중 소금 농도, 시료의 농도로 하였다. General rate (GR) model을 도입하여 1차와 2차 모멘트를 해석하였다. 1차 모멘트 해석에서 평형상수 K를 구할 수 있으며, 이는 $L/u_0$ vs. $({\mu}_1-t_0)/(1-{\varepsilon}_e)(1-{\varepsilon}_i)$]를 도식화했을 때의 기울기이다. 2차 모멘트 해석에서 입자내 확산계수는 이론단수 실험자료에서 계산하였다. 모멘트 분석결과를 통해 여러 물질전달 현상이 이론단 상당높이(HETP)에 주는 영향을 알아보기 위해 van Deemter plot을 작성하고, 총괄 이론단 상당높이($H_{total}$)에 기여하는 $H_{ax}$, $H_f$, 그리고 $H_d$를 조사하였다. 그 중 입자내 확산계수를 나타내는 $H_d$가 가장 지배적이었고, 외부 물질전달 계수를 나타내는 $H_f$의 영향이 가장 미미했다.