• Structural Engineering and Mechanics
• /
• v.11 no.1
• /
• pp.1-16
• /
• 2001

This paper discusses the elastic stability of unbraced frames under non-proportional loading based on the concept of storey-based buckling. Unlike the case of proportional loading, in which the load pattern is predefined, load patterns for non-proportional loading are unknown, and there may be various load patterns that will correspond to different critical buckling loads of the frame. The problem of determining elastic critical loads of unbraced frames under non-proportional loading is expressed as the minimization and maximization problem with subject to stability constraints and is solved by a linear programming method. The minimum and maximum loads represent the lower and upper bounds of critical loads for unbraced frames and provide realistic estimation of stability capacities of the frame under extreme load cases. The proposed approach of evaluating the stability of unbraced frames under non-proportional loading has taken into account the variability of magnitudes and patterns of loads, therefore, it is recommended for the design practice.

• Nuclear Engineering and Technology
• /
• v.5 no.2
• /
• pp.115-131
• /
• 1973

L.S. Pontryagin's maximum principle is applied to the minimum critical mass problem without any restriction on the ranges of uranium enrichment. For the analysis, two group diffusion equation is adopted for a cylindrical reactor neglecting the vertical axis consideration. The result shows that the three-zoned reactor turns out to be most optimal: the inner and outer zones with the minimum enrichment ; whereas the middle 3one with the maximum enrichment. With the given three-zoned reactor, critical condition is derived, which leads to the calculation of the determinant. By finding the roots of the determinant the numerical calculation of the minimum critical mass is carried out for the case of Kori reactor geometry changing the minimum or the maximum enrichment. It is found from many computed values that the least possible critical mass turns out to be the case of 1.2% maximum enrichment for the middle zone and 0.65% minimum enrichment for the inner and out zones.

• Journal of electromagnetic engineering and science
• /
• v.17 no.3
• /
• pp.113-119
• /
• 2017

The application of compressive sensing (CS) to a radar imaging system based on a frequency-scanned microstrip leaky wave antenna is investigated. First, an analytical model of the system matrix is formulated as the basis for the inversion algorithm. Then, $L_1-norm$ minimization is applied to the inverse problem to generate a range-azimuth image of the scene. Because of the antenna length, the near-field effect is considered in the CS formulation to properly image close-in targets. The resolving capability of the combined frequency-scanned antenna and CS processing is examined and compared to results based on the short-time Fourier transform and the pseudo-inverse. Both simulation and measurement data are tested to show the system performance in terms of image resolution.

• Transactions of Materials Processing
• /
• v.19 no.3
• /
• pp.173-178
• /
• 2010

A die cast impeller blade has been developed in the effort on cost reduction in marine equipment industry. The purpose of this work is to optimize the die casting process using Taguchi's design of experiment for minimizing the internal defect of the die cast impeller blade. The experiments were preformed using the numerical simulation based on the L18 orthogonal array. As a results, the internal defect size of the die cast impeller blade for optimal design was controlled less than 1mm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.38C no.6
• /
• pp.497-502
• /
• 2013

In this paper, we aim to evaluate the performance of the digital signal processing (DSP) algorithm used in [8] in order to improve the resolution of spectrometers with fixed number of low-cost, non-ideal filters. In such spectrometers, the resolution is limited by the number of filters. We aim to demonstrate via new experiments that the resolution improvement by six times over the conventional limit is possible by using the DSP algorithm as claimed by [8].

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.22 no.6
• /
• pp.13-18
• /
• 1985

A set of utility programs for automatic generation, minimization and verification of high density PLA layout was developed, which includes equation-to-truth table translator, logic minimizer, PLA product term sorter, file generator for plotting stick diagram, dynamic CMOS PLA layout generator and bipartite row folded CMOS PLA layout generator. Size reduction is performed mainly by logic minimizer and bipartite row folder, and the maximal delay is reduced by sorter. The fOe for automatically generated layout is stored in CIF. Each program was written in Clanguage, and was run on VAX-11/750 (UNIX).

• Journal of Environmental Science International
• /
• v.18 no.6
• /
• pp.675-682
• /
• 2009

Sludge minimization from wastewater treatment plant is becoming more important to save disposal costs and to contribute to sustainable development. For the reduction of sludge production, solubilization and dewaterability of sludge are important factors in sludge processing. Ultrasonic treatment has been used to enhance sludge solubility and dewaterability with anaerobic digestion sludge, primary sludge, and activated sludge. At the ultrasonic power of 0.2 kW/L for 1 hour, anaerobic sludge and activated sludge showed higher solubilization efficiency than the primary sludge in terms of COD, proteins, and suspended solids. Ultrasonic treatment decreased sludge dewaterability and sludge settling characteristics up to 720 kJ/L of ultrasonic energy. In conclusion, ultrasonic treatment was effective for sludge solubilization but it deteriorate dewaterability (specific resistance) and settling characteristics (SVI) of sludge at the experimental conditions.

• Journal of Plant Biotechnology
• /
• v.44 no.4
• /
• pp.388-393
• /
• 2017

We report an Agrobacterium-mediated transformation procedure optimized for 'Kyoho' that is a major table grapevine cultivar in Korea, and its transgenic plants with antifreeze protein gene of carrot (DcAFP). The full length of DcAFP coding region in accordance with the previous report was isolated from young leaves of carrot and recombined into a plant transformation vector. Ethylene inhibitors such as silver nitrate and aminoethoxyvinylglycin (AVG) supplemented in a co-cultivation medium distinctly increased frequency of shoot regeneration when explants were sub-cultured in a selection medium: particularly ten-fold higher in treatment with 0.1 mg/L AVG than one without ethylene inhibitor. Among various antibiotics and their concentrations, the combination of 150 mg/L cefotaxime plus 150 mg/L $Clavamox^{TM}$ was selected for elimination of Agrobacterium cells in addition to minimization of adverse effect on shoot regeneration, while 50 mg/L kanamycin monosulfate effectively suppressed regeneration of non-transgenic shoots. Applying the elucidated culture condition, we finally obtained a total of 5 transgenic 'Kyoho' plantlets with DcAFP, of which integration with the grapevine genome and transcription was confirmed by nucleic acid analyses.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.39 no.2
• /
• pp.169-177
• /
• 2015

Because technology of the sintering process is highly advanced, the gerotor used in the internal gear pumps of vehicles has advantages for manufacturing complex profiles and obtaining durability and minimization. However, it has been necessary to continuously improve the flow rate and noise of internal gear pumps for better fuel efficiency. The existing rotor was designed using a translation algorithm. This caused a discontinuity of the rotor profile, which had adverse effects on the performance. In this study, to improve the discontinuity of the profile, a new design program using a rotation and translation algorithm was developed, and two types of combined multiple profiles (three-ellipses and ellipse 1-involute-ellipse 2) were generated. Then, the performances (flow, flow rate, specific sliding, and pressure angle) of these profiles were calculated. On the basis of the calculation results for the performances, optimal designs of the two types were carried out and verified by comparing their performances with those of the existing rotor profiles.

• Korean Journal of Materials Research
• /
• v.24 no.1
• /
• pp.43-47
• /
• 2014

NiO-doped hibonite pigments were synthesized by the solid state method to get stabilized blue color pigment in both oxidation and reduction atmospheres. Optimum substitution condition with NiO for hibonite blue pigment was investigated. Experimental results were comparable to those of previous cobalt-minimization studies performed with other phosphate- or oxide-based cobalt-containing ceramic pigments (having olivine ($Co_2SiO_4$), spinel ($CoAl_2O_4$), or with co-doped willemite ($(Co,Zn)_2SiO_4$) structures). Composition was designed varying the NiO molar ratio increasing with $SnO_2$. The optimum substitution content is 0.93 mole NiO with 0.75mole $SnO_2$. The characteristics of the synthesized pigment were analyzed by XRD, Raman spectroscopy, SEM, and UV-vis. Synthesized pigment was applied to a lime-barium glaze with 10 wt% each and fired at an oxidation atmosphere of $1250^{\circ}C/1h$ and a reducing atmosphere $1240^{\circ}C/1h$. Blue color was obtained with $L^*a^*b^*$ values at 43.39, -6.78, -18.20 under a reducing atmosphere and 41.66, -6.36, -14.7 under and oxidation atmosphere, respectively.