• Journal of Mechanical Science and Technology
• /
• 제17권6호
• /
• pp.879-887
• /
• 2003

The flow in a parallel walled test channel, when obstructed with a geometry at the entrance, can be forward, reverse and stagnant depending on the position of the obstruction. This interesting flow phenomenon has potential benefit in the control of energy and various flows in the process industry In this experiment, the flat plate obstruction geometry was used as an obstruction at the entry of the test channel. The parameters that influence the flow inside and around the test channel were the gap (g) between the test channel and the obstruction geometry, the length (L) of the test channel and the Reynolds number (Re). The effect of the gap to channel width ratio (g/w) on the magnitude of the velocity ratio (V$\_$i/ / V$\_$o/ : velocity inside/ velocity outside the test channel) was investigated for a range of Reynolds numbers. The maximum reverse flow observed was nearly 20% to 60% of the outside velocity for Reynolds number ranging from 1000 to 9000 at g/w ratio of 1.5. The maximum forward velocity inside the test channel was found 80% of the outside velocity at higher g/w ratio of 8. The effect of the test channel length on the velocity ratio was investigated for different g/w ratios and a fixed Reynolds number of 4000. The influence of the Reynolds number on the velocity ratio is also discussed and presented for different gap to width ratio (g/w). The flow visualisation photographs showing fluid motion inside and around the test channel are also presented and discussed.

• 멤브레인
• /
• 제22권4호
• /
• pp.258-264
• /
• 2012

본 연구에서는 응고조와 도프조성에 따른 투과특성을 알아보기 위해 첨가제로 PEG, PVP를 사용하였고, 상전이법을 이용하여 PSf 평막을 제조하였다. 고분자의 농도, 첨가제의 농도 그리고 응고조의 조성을 달리하여 제막하였다. 평막의 모폴로지와 수투과도를 각각 FE-SEM과 수투과 테스트 장치를 이용하여 측정하였다. 가장 높은 수투과도(986 L/mh)는 PSf 15 wt%, PEG 25 wt% 그리고 응고조로 물이 사용되었을 경우 나타났다. PSf/PEG조성일때 응고조에 DMAc의 함량이 증가할수록 순수투과도는 급격히 감소하였다. 그러한 결과 첨가제의 함량과 응고조의 조성의 변화가 모폴로지와 수투과 특성에 영향을 미치는 것을 확인하였다.

• 상하수도학회지
• /
• 제30권4호
• /
• pp.441-447
• /
• 2016

Development of shale gas has drawn increasing attention since it is one of promising alternative energy resources. However, contamination of groundwater and surface water during the extraction of shale gas is becoming a serious environmental issues, which brings the needs to treat wastewater generated from hydraulic fracking. In this study, the feasibility of membrane distillation (MD) for the treatment of shale gas wastewater was investigated using a laboratory scale experimental setup. Flat-sheet MD membranes were used to treat produced water from a shale gas well in the United States. Different configurations such as direct contact MD (DCMD) and air gap MD (AGMD) were compared in terms of flux and fouling propensity. The foulants on the surface of the membranes were examined. The results suggest that MD can treat the shale gas produced water containing more than 200,000 mg/L of total dissolved solids, which is impossible by other technologies such as reverse osmosis (RO) and forward osmosis (FO). In this study, we investigated the possibility of processing and characterization of shale gas produce wastewater using membrane distillation. Laboratory scale membrane distillation experimental device was developed. It was compared the flat-sheet direct contact membrane distillation and flat-sheet air gap membrane distillation. AGMD flux in lower than the flux of DCMD, it was expected that the contamination caused by organic matters.

• 생물환경조절학회지
• /
• 제6권2호
• /
• pp.117-122
• /
• 1997

$25^{\circ}C$로 유지되고 있는 온실내에서 양액에 세라믹을 처리하여 청경채의 생장을 조사한 결과, 근권온도 3$0^{\circ}C$에서 가장 좋은 생장을 보였다. 특히 세라믹 2호는 각각의 온도 처리구에서 최고의 건물중이 나타난 반면, 3호는 무처리구보다도 오히려 생장이 억제되었다. 줄기와 뿌리의 건물중의 비는 온도가 높아짐에 따라서 증가되었고, 모든 세라믹 처리구에서는 감소되었는데, 이는 세라믹이 뿌리의 생장에 더 많은 영향을 주는 것으로 추정된다. 건물중 1g당 수분의 함량은 모든 세라믹 처리시 무처리구에 비하여 감소되었다. 1% 세라믹은 전기전도도가 0.001-0.03mS/cm으로 낮게 나타났다. 또한 세라믹 중에 파랑색을 띤 3호가 가장 항균력이 강했으며, 모든 세라믹은 물썩음 방지 효과가 있었다.

• 자원환경지질
• /
• 제18권2호
• /
• pp.177-184
• /
• 1985

The carbonate flat pebble conglomerates (CFPC) are interbedded as lenticular bed in the greenish rhythmite of the upper part of $Hwaj{\check{o}}l$ Formation, $Jos{\check{o}}n$ Supergroup. Pebbles are composed mainly of lime-mudstone with small amounts of bioclasts and silt-sized subangular quartz grains. The matrix among pebbles is composed mainly of sparry calcite with relatively much amounts of bioclasts, silt-sized subangular quartz grains and authigenic pyrite crystals or grains. The sparry calcite of the matrix seems to be the results of neomorphism of skeletal sands and bioclasts. The pebbles are well rounded and no plastic deformations are found. Some pebbles show the outer rim of glauconite. CFPC are not associated with any other intertidal features such as stromatolites, flaser bedding and channel structures. Also any features indicative of subaerial exposure such as dessication cracks, fenestrae and so on are not found in the bed. The sedimentological features of CFPC suggest that the following conditions appear to have been necessary for the formation of CFPC : 1) episodic deposition of thin, permeable calcareous beds separated argillaceous beds; 2) preservation of these beds near the sediment-water interface where they could become rapidly cemented; 3) erosion and redeposition of the partially lithified beds by storms or other exceptional erosional events. Eventually storm erosion and redeposition together represent only one of several critical conditions in the genesis of CFPC. The CFPC are very common in Cambrian and lower Ordovician formations, and become very rare in the younger carbonate formations. The expansion of infauna after Ordovician Period eliminated the widespread potential for rapid submarine cementation which is one of the critical factors to form CFPC.

• 대한본초학회지
• /
• 제20권4호
• /
• pp.27-31
• /
• 2005

Objectives : The anticancer response of three different types of water extracts of Zingiberaceae Curcuma longa L. tested for sarcoma 180. Only few studies carried out to investigate the effects of other contents of Curcuma longa L. in anticancer activities, therefore, in this study we have investigated the effects of other component then curcumin in Curcuma longa L. for anticancer a activities. Methods : Three different types of water extracts of Curcuma longa L. were prepared as follows. The sarcoma cells (S180) were maintained in Dulbecco's modified Eagle's medium (DMEM) and were seeded on 24-well cell culture cluster flat bottom with lid tissue culture treated non-pyrogenic polystyrene. The growth of sarcoma 180 was monitored for 1, 2 and 5 days. The sarcoma cells were pictured using inverted microscope and cell density was counted using hemocytometry. Results : After 5 days in the culture medium the results showed high growth of sarcoma 180 for control condition and the surface of CCP plates were fully covered with the cells. In case of medium in which the 10% of filtered water extract of Curcuma longa L. was added a very limited growth of sarcoma 180 was observed. The results were showed only small difference in cell density for two different concentrations of unfiltered water extracts of Curcuma longa L. whereasin case of filtered water extracts the control of sarcoma growth shows better result. Conclusion : The filtered water extracts showed the best result relatively to the unfiltered water extracts for two different concentrations. This indicates that the water extracts of Curcuma longa L. can have anticancer activities possibly without curcumin.

• 신재생에너지
• /
• 제16권1호
• /
• pp.58-67
• /
• 2020

Microbial electrosynthesis has recently been considered a potentially sustainable biotechnology for converting carbon dioxide (CO₂) into valuable biochemicals. In this study, bioelectrochemical acetate production from CO₂ was studied in an H-type two-chambered reactor system with an anaerobic microbial consortium. Metal-rich mud flat was used as the inoculum and incubated electrochemically for 90 days under a cathode potential of -1.1 V (vs. Ag/AgCl). Four consecutive batch cultivations resulted in a high acetate concentration and productivity of 93 mmol/L and 7.35 mmol/L/day, respectively. The maximal coulombic efficiency (rate of recovered acetate from supplied electrons) was estimated to be 64%. Cyclic voltammetry showed a characteristic reduction peak at -0.2~-0.4 V, implying reductive acetate generation on the cathode electrode. Furthermore, several electroactive acetate-producing microorganisms were identified based on denaturing- gradient-gel-electrophoresis (DGGE) and 16S rRNA sequence analyses. These results suggest that the mud flat can be used effectively as a microbial source for bioelectrochemical CO₂ conversion.

• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2003년도 춘계학술발표강연 및 논문개요집
• /
• pp.200-200
• /
• 2003

고체산화물 연료전지(SOFC)에서 사용되는 연결재의 주 기능은 각 단위 셀의 연료극과 다음 셀의 공기극을 전기적으로 연결하여, 공기와 사용연료의 분리역할을 하기 위하여 사용된다. SOFC용 연결재는 다른 구성요소 소재보다, 높은 전자 전도성, 낮은 이온전도성, 우수한 기계 적강도가 요구되며, SOFC는 고온에서 작동되기 때문에, 상온에서 작동온도까지 다른 요소 소재들과 유사한 열팽창계수와 물리, 화학적으로 안정성이 요구된다. 현재 연결재 제조기술은 EVD, CVD, plasma spraying, tape casting 등 다양하게 연구되고 있으며, 본 연구는 세라믹 연결재 증착방법 중 저렴한 비용으로 대량 생산이 용이한 습식법(dip coaling)을 적용하여, 연료극 지지체식 flat-tube형 고체산화물 연료전지의 지지체를 위해 세라믹 연결재를 제조하고, 그 특성을 연구하였다. 세라믹 연결재로써 선정한 합성조성은 LaCr $O_3$에 Ca이 치환 고용된 L $a_{0.6}$C $a_{0.41}$Cr $O_3$으로 pechini법으로 합성하였다. 합성된 조성은 100$0^{\circ}C$에서 5시간 하소후 가속 Ball Milling하여 0.5$\mu\textrm{m}$의 평균입자크기를 얻을 수 있었다. XRD 상분석결과 perovskite상 (L $a_{1-x}$ Ca/x/Cr $O_3$)과 CaCr $O_4$를 얻을 수 있었다. slurry를 제조하여 막의 밀착성을 증진시키기 위해 sand blasting시킨 flat tube지지체에 진공펌프를 이용하여 소재내부와 외부의 압력차로 dip coating한 후, 140$0^{\circ}C$로 소결 하였다. coating 결과 박리현상은 없었으나, 표면과 단면의 SEM분석결과 다소 porous한 박막층이 형성되었으며, Ca이온이 지지체로 permeation되는 현상이 발생하였다. 이와 같은 결과로부터 보다 치밀한 박막생성을 위해, slurry 제조조건을 변화시켰으며, Ca이온의 migration을 막기 위해 barrier layer를 이용하였다 완전 소결된 지지체는 가스투과도와 전기전도도측정을 통하여 특성을 평가하였다.였다.다.

• Korea-Australia Rheology Journal
• /
• 제16권2호
• /
• pp.63-73
• /
• 2004

Flow in a channel with an obstruction at the entry can be reverse, stagnant or forward depending on the position of the obstruction. These flow phenomena have potential applications in the control of energy and various flows in process engineering. Parameters that affect this flow inside and around the test channel are the gap (g) between the obstruction geometry and the test channel, the Reynolds number (Re) and the length (L) of the test channel. The influence of these parameters on the flow behavior was investigated using a flat plate obstruction at the entry of the channel. A low concentration polyacrylamide solution (0.018% by weight) showing a powerlaw fluid behavior was used as the fluid in this investigation. The flow phenomena were investigated by the velocity measurement and the flow visualization and their results were compared with numerical simulation. These results of low concentration polyacrylamide solution are also compared with the results of water published elsewhere (Kabir et al., 2003). The maximum reverse flow inside the test channel observed was 20% - 30% of the outside test channel velocity at a g/w (gap to width) ratio of 1 for Reynolds numbers of 1000 to 3500. The influence of the test channel length (L) and the Reynolds number (Re) on the velocity ratio ($V_i$/$V_o$: inside velocity/outside velocity in the test channel) are also presented and discussed here.

• 대한전자공학회논문지
• /
• 제26권2호
• /
• pp.140-146
• /
• 1989

본 논문에서는 4${\times}$4 블록 절단부호화를 근사화 파라메타 {($Y_{\alpha},\;Y_{\beta}),\;P_{{\beta}/{\beta}}$}에 의한 블록 근사화 및 그 파라메타 부호화의 두 과정으로 나누고, 각 과정에 대해 연구하였다. 제안된 방식은 일단 블록을 평탄 및 에지블록으로 분류하여 평탄 블록은 한개의 근사화 레벨 Y로만 근사화하도록 하였다. 에지블록의 라벨 평면 $P_{{\beta}/{\beta}}$는 준비된 32개의 표준 패턴을 이용하여 근사화하도록 노력하였고, 근사화가 어려운 것은 그대로 전송하였으며, 근사화 레벨 $Y_{\alpha},\;Y_{\beta}$는 이미 전송된 라벨 평면을 이용하여 예측 양자화한 후 Huffman 부호화하도록 하였다. 본 방식의 성능은 배경부분에서의 표현에는 약간의 문제가 있는 것으로 나타나지만 SNR 면에서는 복잡한 변환 부호화 방식보다도 좋은 결과를 보이며, 특히 에지가 잘 보존되었다.