• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 추계학술대회 논문집 학회본부 A
• /
• pp.61-63
• /
• 1999

This paper reports analysis and test results on the new type Linear Oscillatory Actuator(LVDT actuator) which has been expected to be applied not only to measure position but also to drive as an actuator at the same time.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권4호
• /
• pp.487-490
• /
• 2014

The conventional motor-driven MCCB (molded-case circuit breaker) is not only large in size, but also inefficient in performance. To solve these problems, this paper suggests SPMA (separate permanent-magnet actuator), a novel magnetic actuator. In this paper, SPMA is designed for a 225AF MCCB and compared to a conventional motor-driven MCCB and to an EMFA (electro-magnetic force driving actuator)-type MCCB.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1999년도 하계학술대회 논문집 G
• /
• pp.3322-3324
• /
• 1999

This paper studies on the design and fabrication of a micro in-plane positioning actuator integrated with a microlens. Proposed in-plane actuator is a micro XY-stage which is composed of two linear comb drive actuators being orthogonal to each other. In the fabrication of actuator, the single crystalline silicon substrate anodically bonded with a #7740 glass substrate is used because of simple release and passivation. The structure of actuator is formed on the silicon facet of bonded fixture by chlorine-based deep RIE and then released by isotropic wet etching of glass (#7740) in hydrofluoric acid solution. Fabricated actuator has a large travel range up to $30({\pm}15){\mu}m$ and high resolution less than 0.01f1l1l in each direction. Experimented resonant frequency of this actuator is 630Hz. The micro-Fresnel lens is fabricated on the square-shape glass structure prepared in the center of actuator.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1996년도 하계학술대회 논문집 C
• /
• pp.1974-1976
• /
• 1996

An electrostatically driven comb actuator with $525{\mu}m$ height was fabricated using (110) Si anisotropic etching in the Potassium Hydroxide(KOH) solution. The etch-rate and etch-rate ratio are strongly dependent on the weight % and temperature of KOH solution. We developed the optimal condition for the anisotropic etching on (110) wafer with varying these conditions. The force that the comb-drive actuator generates is inversely proportional to the distance of gap and proportional to the height of the comb electrodes. The electrodes must have the high aspect ratio. The (110) Si anisotropic etching is very useful to get a high aspect ratio structure.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.384-387
• /
• 2006

Vertical L/UL (Load/Unload) velocity is very important parameter to determine the L/UL performance, and the vertical velocity is determined by the actuator velocity and the ramp profile. However, it is not easy to precisely control the actuator rotating velocity during the L/UL process. Especially in emergency parking, servo system doesn't operate, it is impossible to control an actuator velocity. Then, the vertical unloading velocity depends on only ramp profile. The ramp height and the sliding length for L/UL process in SFF (Small Form Factor) HDD are restricted due to slimness and small media. For these reasons, it is very difficult to design the ramp profile in SFF HDD. Therefore, this study analyzes the unloading dynamic characteristics for various ramp profiles and makes the thesis for ramp profile design.

• 정보저장시스템학회논문집
• /
• 제2권2호
• /
• pp.150-155
• /
• 2006

Vertical L/UL (Load/Unload) velocity is very important parameter to determine the L/UL performance, and the vertical velocity is determined by the actuator velocity and the ramp profile. However, it is not easy to precisely control the actuator rotating velocity during the L/UL process. Especially in emergency parking, servo system doesn't operate, it is impossible to control an actuator velocity. Then, the vertical unloading velocity depends on only ramp profile. The ramp height and the sliding length for L/UL process in SFF (Small Form Factor) HDD are restricted due to slimness and small media. For these reasons, it is very difficult to design the ramp profile in SFF HDD. Therefore, this study analyzes the unloading dynamic characteristics for various ramp profiles and makes the thesis for ramp profile design.

• 대한기계학회논문집A
• /
• 제40권1호
• /
• pp.17-22
• /
• 2016

바코드 리더를 위한 전자기력을 이용한 소형 회전 무빙 코일 타입 보이스 코일 구동기를 개발하였다. 본 구동기는 1 개의 자석과 1 개의 코일 그리고 1 개의 복원핀으로 이루어진 간단한 구조이다. 구동기는 DC 모터의 선형으로 근사화한 이론적인 모델링으로 해석하고, 유한 요소 해석 프로그램으로 모터 상수와 복원력 상수를 계산하여 동적 성능을 예측하였다. 공진 주파수는 64 Hz 이며 바코드 리더를 위한 50 Hz 의 주파수에서 60 deg 의 반사각을 가짐으로 예측되었다. 시작품을 제작하여 실험을 통하여 3 V 의 입력 전압에서 50 Hz 의 주파수에서 61.8 deg 의 반사각을 가짐을 확인하였다. 제안된 구동기는 Op-amp 를 이용하여 간단한 개루프 제어 회로 구성이 가능하다.

• 대한기계학회논문집A
• /
• 제41권2호
• /
• pp.81-85
• /
• 2017

섬유강화 고분자 복합재료는 섬유 형태의 강화제와 고분자 형태의 기지재료가 결합된 형태로 이는 무게 대비 고강도 및 고강성의 구조물 제작에 용이하다. 본 연구에서는 형상기억합금 와이어가 삽입된 섬유 강화 지능형 연성 복합재 구동기를 제작, 이의 재료 구성에 따른 거동 특성을 평가 하고자 한다. 구동기는 형상기억합금이 포함된 구동층과 일반 구조층으로 구성되어 한 층씩 적층되는 방식으로 제작되며 재료 구성에 따른 거동 특성을 살펴보기 위하여 일반 구조층으로 사용된 유리섬유 직물의 적층 수, 기지재료의 종류를 달리한 뒤 구동 특성을 살펴보았다. 또한, 구동 시에 요구되는 인가 전류의 양을 달리하여 최대 구동각과 최대 구동각에 도달하는 구동 시간을 측정하였다.

• Journal of international Conference on Electrical Machines and Systems
• /
• 제3권4호
• /
• pp.481-486
• /
• 2014

The demand for a DC power distributed system is increasing as renewable energy sources and DC electrical load are proliferating. For the automation of a power system, a magnetic contactor for the DC power system is required. The conventional magnetic contactors are mostly equipped with a solenoid magnetic actuator. However, the conventional magnetic contactor has problems with continuous power consumption, and heat generation. To address these problems, a permanent magnet type DC magnetic contactor is proposed in this paper.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.326-331
• /
• 2007

This paper conducts a vibratory loads reduction analysis of an Advanced Active Trailing-edge Flap (AATF) blade utilizing single crystal piezoelectric actuators. For an AATF blade, a new L-L piezostack actuator using single crystal PMN-PT materials is designed. The AATF blade is designed to have similar characteristics to the Advanced Active Twist Rotor (AATR) blade. The active trailingedge flap is assumed to be 20% of the blade span and 15% of the chord, located at 75% of the blade radius. In order to conduct the vibratory loads reduction analysis of the AATF blade in forward flight, DYMORE, a multi-body dynamics analysis code, is used. The simulation result shows that the hub vibratory loads may be reduced by approximately 89% even with a much lower input-voltage when comparing with the other active rotor systems.