• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.32 no.1C
• /
• pp.34-42
• /
• 2007

The sphere decoder (SD) has recently been proposed to perform maximum likelihood (ML) decoding for multi-input multi-output systems. Employing a 'breadth-first' searching algorithm for closet points in a lattice, we propose a novel ML decoding scheme for multi-input multi-output systems. Simulation results show that the proposed scheme has the same bit error rate performance as the conventional ML decoders while allowing significantly lower computational burden than the SD.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.48 no.9
• /
• pp.510-516
• /
• 1999

In this paper, a new high-powerfactor control method for boost-type rectifier is proposed, which removes the necessity of input current sensing. This method generates a sinewave duty template only from the line voltage waveform and rectifier output, and reduces reactive power remarkably utilizing three compensation coefficients which are determined through experiments. These compensations make the input current to be in phase with the input voltage all over the load range. A prototype boost-type rectifier is designed and experimental results are presented.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.45 no.1
• /
• pp.30-41
• /
• 1996

Current Source(CS) PWM converter is appropriate for the magnet power supply system which requests high power and high precision current control. Input and output filters should be installed to eliminate the current or voltage harmonics caused by the PWM switching for the CS PWM converter. But the input/output filters limit the output DC current range and may destroy the system with filter resonance, and make the system equation more complicated. In this paper, systematic and simple filter design method which considers not only the harmonic attenuation but also the total system good transfer function characteristics in the dc filter. The simulated and experimental results verify the proposed theory. (author). refs., figs., tabs.

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.9
• /
• pp.546-551
• /
• 2000

A micromechanical switch that can be used as a logic gate is described in this paper. This switch consists of fixed input electrodes an output electrode Vcc/GND electrodes and movable plates suspended by crab-leg flexures. for mechanical switching of an electrical signal a parallel plate actuator which comes in contact with output electrode was used. Provided that movable plates are connected to Vcc and a low input voltage(ground signal) is applied to the fixed input electrodes the movable plates are pulled by an electrostatic force between the fixed input electrodes and the movable plates. the proposed micromechanical switch was fabricated by surface micromachining technology with$2\mum$ -thick poly-Si and the measured threshold voltage for ON/OFF switching was 23.5V.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.12
• /
• pp.1810-1817
• /
• 2015

The railway vehicle has an auxiliary power unit for supplying power to the associated electronic control devices and passenger service unit. Typically, input voltage from the catenary for rolling stock is highly fluctuating according to the substation capacity, vehicle propulsion and regeneration. Especially, the frost and freezing on contact wire in winter can cause a blackout inside vehicle, and also brings about electronic components damaging and the system down. To prevent this problem, a large filter and capacitor is used. But this is not a perfect solution, because it is increasing weight of the unit. In this paper, a new algorithm is proposed to suppress the disturbance without adding devices. Simulation and experimental results show that the proposed algorithm has performance to suppress the disturbance at the sudden input voltage variations.

• Proceedings of the Korean Society of Broadcast Engineers Conference
• /
• 1999.06a
• /
• pp.207-212
• /
• 1999

In VEs (virtual environments) such as a CAVE system, there are three important operations : executive command decision, object selection and 3-D (three-dimensional) pointing. It is necessary to implement these operations in VEs intuitively and accessibly. In CAVE, it is possible for examines to walk and change their viewpoints freely. Then, the input devices which have excellent portability and rich expression are desired. Speech input satisfies both requirements. It is, however, very difficult for the speech input to indicate an exact point in 3-D space. Therefore, an extendable virtual stick is employed and it supports speech input. This paper proposes a user friendly interface using speech and a virtual stick in CAVE system. In this paper, several applications appropriate for the proposed interface are developed. Some problems are pointed out from the applications.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.2
• /
• pp.102-109
• /
• 2000

This paper deals with an observer-based preview control for semi-active suspensions. An Observer has been designed such that all the state variables and road inputs can be estimated from accelerations. Since the road input to the rear wheels is a delayed version of that to the front wheels, it can be obtained by estimating the road input to the front wheels without preview the estimated values of state and the estimated road input has been investigated. The results show that the observer-based control can provide good performance. The observer-based preview control improves the dynamic behavior of the rear axle and that of pitch motion compared to the LQ optimal control.

• Journal of Korean Institute of Industrial Engineers
• /
• v.18 no.1
• /
• pp.63-80
• /
• 1992

The concept of rapid prototyping intended for a significant reduction in cost and lead time becomes even more practical with the recent development of various equipments to make the concept concrete. For the purpose of real application of commercially available SLA(stereolithography apparatus), this paper is intended to develop the standard conversion procedure from CAD data to the input data for SLA. While the procedure presented in this paper is based on CAD system "CATIA" and SLA of 3D systems, Inc., which are being used in authors' company DAEWOO Motor Co., Ltd., the basic concept of this paper can be applied to any other CAD systems and machines of using stereolithography process. The algorithm presented in this paper is classified into two stages-node sampling and triangulation. First of all, point data are sampled through the node sampling procedure, and then these are triangulated so that the input data for SLA operation is finally generated. The suggested method is devised in a way to meet the input requirements of SLA and more importantly consume less computation time and generate less number of input data for SLA.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2003.11a
• /
• pp.397-401
• /
• 2003

A resonant type voltage source and power device and a control method using Pulse Density Modulation(PDM) power control and Pulse Width Modulation(PWM) voltage control for plasma sterilization are described. For the stability of discharge in the generating tube, it is desirable that the peak apply voltage is constant The PDM power control is employed for sustaining the voltage constant at any generating tube input power. Moreover, to avoid the influence of input AC voltage fluctuation etc., PWM voltage control with generating tube peak voltage feedback is used. Both functions were confirmed by the experiment with 6.5[㎑], 1.8[㎾] inverter and generating tube. The effect of input synchronous PDM method for input current stabilizing is confirmed also.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.60 no.4
• /
• pp.781-788
• /
• 2011

This paper proposes a boost-input self-driven active clamp ZVS converter eliminating the extra dirve circuit for the active clamp switch. The converter used the auxiliary winding of the transformer to drive the active clamp switch and to achieve asymmetrical duty control. This paper presents the operation principle and the analyzed results of dynamic characteristics including steady state characteristics of the converter proposed. The experimental results were used to verify the theoretical predictions. A 300W (15V/20A) prototype converter that only exhibited 2-turn winding number in the auxiliary winding was sufficient to drive the active clamp switch on the input voltage of 80V. Finally, the maximum efficiency of 91.2% was achieved for the prototype converter and the proposed converter had stable closed loop characteristic with phase margin $55^{\circ}$.