• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(III)
• /
• pp.275-280
• /
• 2003

The Korean high speed train is designed to run at very high speed such as 350km/h. At this time, ballast in roadbed is dispersed by high speed air flow and this hits the substructure of the train. It becomes the factor of damaging the train. To investigate the main factor and possibility of ballast dispersion, the substructure flow is measured by Kiel-Probe Array System at G7 train experiment. And the wind tunnel experiment is performed with ballast in our research. Also CFD analysis is performed by assuming that the flow field is 2D and using simple shaped cross-tie and flat substructure of the train. By comparing the experimental results and CFD analysis, the accuracy of the analysis is checked. They will become the basic research data for the analysis and optimization of train substructure to prevent the ballast dispersion.

• International Journal of Railway
• /
• 제7권4호
• /
• pp.100-108
• /
• 2014

A numerical analysis method for predicting aerodynamic noise at inter-coach space of high-speed trains, validated by wind-tunnel experiments for limited speed range, is proposed. The wind-tunnel testing measurements of the train aerodynamic sound pressure level for the new generation Korean high-speed train have suggested that the inter-coach space aerodynamic noise varies approximately to the 7.7th power of the train speed. The observed high sensitivity serves as a motivation for the present investigation on elucidating the characteristics of noise emission at inter-coach space. As train speed increases, the effect of turbulent flows and vortex shedding is amplified, with concomitant increase in the aerodynamic noise. The turbulent flow field analysis demonstrates that vortex formation indeed causes generation of aerodynamic sound. For validation, numerical simulation and wind tunnel measurements are performed under identical conditions. The results show close correlation between the numerically derived and measured values, and with some adjustment, the results are found to be in good agreement. Thus validated, the numerical analysis procedure is applied to predict the aerodynamic noise level at inter-coach space. As the train gains speed, numerical simulation predicts increase in the overall aerodynamic sound emission level accompanied by an upward shift in the main frequency components of the sound. A contour mapping of the aerodynamic sound for the region enclosing the inter-coach space is presented.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 A
• /
• pp.342-345
• /
• 1997

To achieve adequate brake performance in high-speed trains the brake system should : ${\bullet}$ offer high reliability and high availability, ${\bullet}$ permit deceleration of the train with as little wear as possible, and ${\bullet}$ display good control characteristics with, if possible, infinitely variable control of the braking effort. For these reasons, high-speed train is to be equipped with three different and largely independent brake system : ${\bullet}$ a regenerative brake with regenerative feedback in the driven cars, ${\bullet}$ a linear eddy-current brake in the nondriven cars and ${\bullet}$ a pneumatic disc brake in all cars. This paper describes the conceptual design of braking system for Korea High Speed Train with the maximum speed of 350km/h

• 한국정밀공학회지
• /
• 제31권9호
• /
• pp.773-776
• /
• 2014

KTX (Korea Train eXpress) is the first high-speed train operated in Korea and its highest speed reaches 300 km/h. Korean high-speed trains are mostly operated on the railroads exclusively designed for high-speed trains, but the sections of Seoul~Gwangmyeong, nearby of Daejeon station and Dongdaegu are operated on the existing tracks having the speed less than 150 km/h. With this paper, we'd like to analyze the lateral force that occurs between the wheels and the rail when high-speed trains were operated on the existing track section to suggest an appropriate driving speed for high-speed trains. As the rigid wheel base of the high-speed train is 3m which is about 50% longer than normal vehicles, it works as an advantage for high-speed driving. However, as the lateral force becomes higher than normal vehicles when driving on curves, plans to reduce wear-outs on the wheels are required.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.948-949
• /
• 2008

In this paper, an effect on power conversion unit in next generation high-speed train by loss of contact between a contact wire and pantograph supplied electrical power to high-speed train are investigated. One of the most important needs accompanied by increasing the speed of high-speed train is reduced that arc phenomenon by loss of contact brings out EMI. To analysis of conducted EMI source on powering mode of next generation high-speed train, it is necessary electrical modeling system between the contact wire and the pantograph according with loss of contact. Therefore analytical model of a contact wire and a pantograph is constructed to simulate the behaviour of loss of contact. The reliability of the modeling system is verified by simulation implementation on loss of contact.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2015년도 제46회 하계학술대회
• /
• pp.1595-1596
• /
• 2015

This study presents the review of technical requirements of safety and security for the developed high-speed freight train which will be serviced on the existing route of the high-speed line. There is no any experience to make a system design of high-speed freight train in Korea until now. We need to make a new regulations of commercial service.

• 한국정밀공학회지
• /
• 제29권6호
• /
• pp.593-599
• /
• 2012

To analyze the effect of the track structure on the running performance of the railway vehicle, we studied on the vibration and ride characteristics of the high speed train. As results, vibration and ride level of high speed train on the concrete bed track is more reduced than on the ballast bed track. Peak-peak value of carbody vibration on the concrete bed track at 300km/h is half of the peak-peak value of carbody vibration on the ballast bed track. Ride level on the concrete bed track at 300km/h is same level as that on the ballast bed track at 250km/h. Thus, Vibration and ride performance of the high speed train on the concrete bed track is greatly improved compared with that on the ballast bed track.

• 한국전산유체공학회지
• /
• 제1권1호
• /
• pp.81-87
• /
• 1996

The aerodynamic charateristics of high speed train can be improved by well-designing of its fore-body shape. In this paper, as a way of the design a fore-body shape which has optimal aerodynamic charasteristics, 9 models of fore-body shapes are proposed and the change of aerodynamic charateristics is studied through calculations of flow field around high speed train for each fore-body shape. The flow field around high speed trains are calculated using Thin-Layer Navier-Stokes equation and Chimera grid technique. The application of Chimera grid technique to these flow calculations over high speed train which has ground plane under the train makes grid generation easily. As a computaional algorithm, Pulliam and Chaussee's Diagonal algorithm, the modified form of the Beam and Warming's AF scheme which operates on block-tridiagonal matrices, is selected to reduce computaional time. Introducing hole points flag concept to this Diagonal algorithm. a algorithm for Chimera grid is generated. The variational trends of aerodynamic characteristics are studied from the results of flow calculations around high speed trains for 9 fore-body shapes.

• 대한기계학회논문집B
• /
• 제28권6호
• /
• pp.734-739
• /
• 2004

The aerodynamic effect on platform during the train passage, the results of field test on the high-speed railway platform are discussed and the whole test results and conclusions are synthesized. The field test for the high-speed railway have been conducted on the Osong temporary platform in the newly constructed Seoul-Busan high-speed line and total 12 measurements have been conducted for G7 train and KTX train. The results shows that the high-speed trains have similar aerodynamic characteristics and have far better characteristics referring to the conventional trains such as Saemaul and Mugungwha trains. To discuss the actual aerodynamic effects on the platform at its own operational speed, Beaufort wind scale have been introduced and the criteria for the safety on railway platform has also been discussed.

• 한국소음진동공학회논문집
• /
• 제14권10호
• /
• pp.999-1006
• /
• 2004

Recently, the ride comfort problem becomes increasingly important because of today's needs for train speedup. The railway has the track irregularities which cause vibrations, such as rail joints, turnout, level crossing, transition corves and super-elevation ramps, and variations in the track level(z-axis) and the gauge(y-axis). In Korea, the service run of the high speed train has been made since the 1st of April, 2004. The commercial high-speed trains must be run on the compound lines which are composed of high-speed line and conventional line. The high speed lines in both Kyoungbu line and Honam line have 57.5％ and 33.8％, respectively In this Paper, the ride comfort has been reviewed by the various experimental methods when the high-speed trains are operated on both Kyoungbu line and Honam line. The results show that the high-speed train has no problems from the viewpoint of the comfort ride during the operation on the high speed line and conventional line.