• Journal of Hydrogen and New Energy
• /
• v.24 no.4
• /
• pp.302-310
• /
• 2013

As an initial step to develop a liquid hydrogen pump of piston type operated under cryogenic and high pressure, leakage and piston head shape for the piston pump were discussed with temperature and pressure. As the results, the leakage depended on correlation among density, viscosity, clearance area by the low temperature. In order to reduce the leakage, it was found that the air-tightness can be improved by minimizing contact surface between piston and cylinder, and also increasing pressure in-cylinder can reduce piston clearance. Among the proposed piston shapes, D type piston shape had the most air-tightness. D type piston had smaller contact surface than other piston shape and easier expansion of cup shape by pressure. The leakage of D type piston shape was found about 7%, compared with A type piston shape. But it was required that analyze about vapor lock by friction and wear resistance.

• Journal of the Korea Fashion and Costume Design Association
• /
• v.12 no.2
• /
• pp.1-20
• /
• 2010

This thesis is about "manggon" that holds down man's top knot hair and its accessaries "pungjam", "kwanja". manggon was seen first time in the mural of Donwhang kae won chon bo during T'ang period (713-756). The "Tu Aek Ra" manggon shown in this mural would be the origin and beginning of maggon's usage. Also the "Sha" that was placed on top of the hair for decoration purpose is believed to be a former form of "manggon" Before the short hair cut was enforced, wearing the "kwan"(head gear) was considered as an impotant etiguette. Thus the head gear was treasured and the manggon which was the most essential piece to cover down the hair before to put on the head gear was regarded as the most important piece. However, since the manggon was tied very tightly around the forehead, manggon caused some sickness. From my private collections of man's head gears and ornament, 121 items were selected and used for analysis and the followings were found: 1. Pungjam was divided into 8 categories according to its shape and a research was made on its unique structural characteristic on each categories. 2. Kwanja's material and design that were used are all in accordance to the historical recordings.

• Clinics in Shoulder and Elbow
• /
• v.20 no.1
• /
• pp.46-48
• /
• 2017

There are many methods of making cement spacer in patients who require a two-staged operation for humeral head osteomyelitis. However, limitation of motion after the first surgery-due to inadequate size and insufficient intra-articular space for second surgery-remain to be an issue. To mitigate this issue, we made a cement spacer with the same size and shape of the patient humeral head. Four patients with humeral head osteomyelitis were enrolled in this study. To make the cement spacer, we used the Mimics program, and designed the molding box by a reverse engineering technique. We evaluated the range of motion and pain using a Constant score. The mean abduction was $50^{\circ}$($40^{\circ}-60^{\circ}$), forward flexion was $50^{\circ}$ ($30^{\circ}-70^{\circ}$), and average Constant score was 47.75 (44-52). Three-dimensional printed molding technique is one of the effective methods for humeral head osteomyelitis allowing for daily activities prior to the second surgery.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2009.10a
• /
• pp.870-871
• /
• 2009

• Journal of the Korean Magnetics Society
• /
• v.10 no.6
• /
• pp.310-317
• /
• 2000

With use of (G)MR head, thermal asperity (TA) has been a big concern in drive industry. In this study, we investigated several factors of heads and disks which affects the TA sensitivity of the drive. TA experiments were conducted by introducing the particles on the drives using a particle injection chamber. It was found that the slider ABS shape can help to reduce TA or contamination in the head/media interface. However, TA sensitivity of the drive mainly depend on the intrinsic property of (G)MR sensor. GMR head is much less sensitive to TA compared with MR head. However, in case that the same bias current was applied for both of MR and GMR head, TA sensitivity of GMR head became almost identical to that of MR head. Therefore it was found that the bias current is a dominant factor in determining TA sensitivity of the head. TA sensitivity of different types of disks was also studied. The scratch resistance of the carbon overcoat layer is the one of the main factors which influence TA rejection capability of the disks.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2012.10a
• /
• pp.851-852
• /
• 2012

• Journal of computational fluids engineering
• /
• v.6 no.1
• /
• pp.14-20
• /
• 2001

The CFD analysis of the three-dimensional turbulent flow in the impeller and diffuser of an axial flow pump was performed. Not only the design point but also the off-design points were computed. The results were compared with available experimental data in terms of head generated. At the design point, the analysis accurately predicted the experimental head value. In the range of the higher flow rates, the results were also in very good agreement with the experimental data, not only in absolute value but also in term of slope. Although experimental data to be compared were not available in the range of the lower flow rates, the results well described the S-shape performance curve of the axial pump characteristic.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.158-160
• /
• 1997

WHEN IT IS REQUIRED TO CONNECT OVERHEAD TRANSMISSION LINE WITH UNDERGROUND CABLE, PREVALENT METHOD WAS TO USE CABLE HEAD TYPICALLY MADE OF LATTICE STEEL STRUCTURE. BUT IN VIEW OF THE INCREASING DEMAND THAT STEEL STRUCTURE INSTALLED IN URBAN AREA AND/OR RESIDENTIAL AREA NEED TO MATCH WITH ENVIRONMENTAL SURROUNDINGS, THE UNSHAPELY LARGE-SIZED LATTICE STEEL STRUCTURE CAN NOT BE A PROPER ONE BECAUSE THAT IT IS NOT WELCOMED BY THE RESIDENTS AND ACCORDINGLY ITS INSTALLATION TENDS TO CONFRONT WITH CIVIL PETITION. AS AN ALTERNATIVE METHOD TO SETTLE AFOREMENTIONED UNFAVOURABLE SITUATION WE MAY BE UNDER, WE AR INTENDING TO DEVELOP THE CABLE HEAD MADE OF TAPERED TUBULAR STEEL POLE AND TO PUT IT TO PRACTICAL USE. THE ADVANTAGE WE CAN TAKE OF THE TAPERED TUBULAR STEEL POLE IS THAT IT CAN BE INSTALLED IN A VERY LIMITED SPACE MAXIMIZING THE UTILITY VALUE OF THE LAND AND THAT ITS SMART SHAPE WITH COLOUR COATING IN CONSIDERATION OF AESTHETIC AESTHETIC CAN BE IN GOOD HARMONY WITH THE SURROUNDINGS.

• Proceedings of the KIEE Conference
• /
• 2002.11d
• /
• pp.70-72
• /
• 2002

LPM that is used for head driver is problem of miniaturization of construction and cost. This can be achieved by most suitable shape decision. and suitable selection of control system. Specially, in LPM that Full step is mm$\sim$um unit. the large change of thrust receives much effect by tooth number per pole. tooth width and slot width about change of the air gap length. Therefore, this paper presents LPM that use for suitable head driver to reduce of the structure and the cost. to generate maximum thrust of LPM, and finds the proportion of the tooth pitch to tooth width and the slot width about change of the air gap length through FEM analysis. Also, applying different tooth width and slot width that is given as analysis result. this paper presented model that thrust is improved.

• Proceedings of the KIEE Conference
• /
• 1998.07g
• /
• pp.2370-2372
• /
• 1998

Recently we have developed an active stereo head-eye system with vergence, name it KIST HECter(Head-Eye System with Colored Stero Vision), based on the analysis of human's neck and eye motion at visual behavior. Our HECter is a five degree-of-freedom system composed of pan and tilt motion in neck part and independent vergence motion of binocular cameras and commonly shared elevation axis in eye part. And stereo vision Provides two color image, which are processed by powerful each TMS32080 vision board. The shape and size are designed to be almost same as human face. The ability to vergence has significant importance and gives many beneficial merits. On its mechanical implementation we adapt a non-parallelogram 4-bar linkage mechanism since it provides high accuracy in transfering motion and enables compact and flexible design.