• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.1200-1203
• /
• 2017

Propulsion system test complex (PSTC) is designed to verify propulsion system of KSLV-II. It is composed of hydraulic and pneumatic system, test stand system, control/measurement system, and flame deflector and safety system. In this study, kerosene filling system of hydraulic and pneumatic system is introduced. It performs store and chilling of kerosene, chilling and purging of filling line, and filling and retrieval of the kerosene. The kerosene supply requirements of 1, 2 and 3 stages of KSLV-II are considered in design process.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.21 no.3
• /
• pp.76-83
• /
• 2017

Korea Aerospace Research Institute(KARI) has been developing a new launch vehicle Korea Space Launch Vehicle-II(KSLV-II) with their own technology. Thus, it is required a new launch complex that corresponds to a new propulsion system of launch vehicle. Because widely changing of KSLV-II comparing with KSLV-I such as thrust of engine system, composition of vehicle staging, pneumo-hydraulic scheme of propulsion system, it is important to establishing appropriate ground support equipments for fuel(kerosene) filling. In this critical design process, specific supply line and specification of components are designed and the concept of kerosene filling is determined based on results of preliminary design. Also, plans of supply operation and prerequisite are established and operation algorithms are formed.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.4
• /
• pp.50-58
• /
• 2016

Korean Space Launch Vehicle (KSLV-II) Propellant Supply System charges liquid oxygen and kerosene to each propellant tank for the stages. To charge the launch vehicle propellant tank safety, the propellant charge flow rates and scenarios should be defined. First, the Propellant Supply System was modeled with 1D flow analysis program. The control valve capacity and orifice size were calculated by performing the 1D steady state simulation. Second, the 1D transient simulation was performed by using the steady state simulation results. As propellants were being charged at the each tank, the increased tank liquid level decreases the charge flow rate. Consequently, the proposed supply system satisfies the required design charging conditions.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.5-13
• /
• 2017

To lunch the Korea Space Launch Vehicle-II(KSLV-II), the second launch complex will be constructed on the Naro Space Center and Kerosene Filling System (KFS) will be also installed newly. KFS of KSLV-II launch complex system is being designed based on Naro Launch Complex. But this must supply fuel to fuel tanks of the vehicle with only a supply pump because KSLV-II is a 3-stage launch vehicle unlike Naro Launch Vehicle or Test Launch Vehicle (TLV). A sudden rise of pump output pressure is recognized during fuel filling scenario selection process. This occurs because return flow can not actively deal with a lot of flow change using flow control method of orifice type. To solve this problem, it is verified that fuel can be stably supplied by installation of accumulator and an appropriate adjustment of filling mode change sequence through flow analysis of various cases.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.22 no.5
• /
• pp.132-140
• /
• 2018

To lunch the Korea Space Launch Vehicle-II(KSLV-II), a second launch complex will be built at the Naro Space Center, and a Kerosene Filling System (KFS) will be installed. KFS of KSLV-II launch complex system is being designed based on Naro Launch Complex. But this must supply fuel to fuel tanks of the vehicle with only a supply pump because KSLV-II is a 3-stage launch vehicle unlike Naro Launch Vehicle or Test Launch Vehicle (TLV). A sudden rise of pump output pressure is recognized during fuel filling scenario selection process. This occurs because return flow can not actively deal with much flow change using the orifice-type flow-control method. To solve this problem, it is verified that fuel can be stably supplied by installing an accumulator, designed for appropriate adjustment of filling-mode change sequence via flow analysis of various cases.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.676-677
• /
• 2010

In Naro Space Center, Naro launch vehicle launched 2 times. Launch pad for Naro launch vehicle in Naro space center equipped propellant feeding facility for operating launch process. This paper studied development process and operating method for liquid oxygen filling system of cryogenic propellant systems in launch pad propellant feeding facility.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.288-293
• /
• 2001

This paper presents the water-hammer effect due to the rapid opening and closing of isolation valve and thruster valve in the spacecraft propulsion system. The single propellant feed system was modeled to investigate the maximum peak pressure due to the water-hammer effect. The test parameters are tank supply pressure, shape and throat length of orifice and line length. Kerosene was used as the inert simulant propellant liquid instead of hydrazine. As downstream line length after isolation valve increased from 1.5 to 2.5m, the maximum line-filling water-hammer peak pressure decreased, but the average time interval between peak pressures increased. The maximum line-filling water-hammer peak pressure with orifice was lower than without orifice, and the maximum line-filling water-hammer peak pressure with orifice at the back of isolation valve was lower than with orifice in front of isolation valve. Without orifice, the maximum water-hammer peak pressure due to the rapid opening and closing of the thruster valve was about 126% of tank supply pressure. With orifice, it decreased. As orifice throat length increased, it decreased. The maximum water-hammer peak pressure due to the rapid closing of the thruster valve with converging-diverging orifice was lower than normal orifice. It was found that the orifice as a means of pressure drop was very effective to reduce the water hammer peak pressure at the thruster valve. The results of this study can be used for the design of spacecraft liquid propulsion feed system.

• Proceedings of the Korean Institute of Resources Recycling Conference
• /
• 2006.09a
• /
• pp.3-12
• /
• 2006

The main feature of these total technologies is that we can constitute the optimum treatment scheme fitting to the property of wastes, amount of wastes and energy requirement. For high moisture content wastes or biomass resources, high pressure steam process (MMCS) for crush, dry and deodorize wastes to produce high quality fertilizer of fuel is most appropriate. For dry or semi-dry solid wastes, the STAR-MEET system can be applied to produce low-BTU gases for power generation using duel fueled diesel engines of Stirling engines, and the REPRES and HyPR-MEET systems can be applied to produce hydrogen rich medium-BTU gas. For waste plastics and oils, liquefaction technology is best fit to produce light oil or kerosene equivalent fuel oils. These total technologies are completely different from the existent waste treatment technologies based on land-filling or incineration, and are expected to disseminate all over the world in the near future.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.11a
• /
• pp.97-100
• /
• 2009

Cold flow and ignition tests were performed for a technology demonstration model of a 75-tonf thrust chamber which is a candidate liquid rocket engine for a next Korea Space Launch Vehicle. The test facility was modified to support the new concepts of the thrust chamber such as ignition system, film cooling and LOx leading supply. The hydrodynamic characteristics of the supply pipelines, thrust chamber and igniter as well as the filling time of the propellants were obtained through the cold flow tests on the LOx and kerosene and the ignition cyclogram was determined using the results. The ignition test was successfully accomplished according to the cyclogram and therefore, a basic information was obtained for further hot firing tests.