• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.3
• /
• pp.18-27
• /
• 2000

Signal attenuation of Ka-band satellite communication system due to rain fading is more severe than those of conventional frequency band system, thus an efficient rain fade countermeasure technique is absolutely required. In this paper, we design an improved adaptive modulation system, which switches the modulation mode according to the channel condition, and propose the novel synchronization algorithms. We assume that the modulation scheme is M-ary PSK and the receiver is TDMA burst mode. And the transponder model is the same with KOREASAT-3. By using the adaptive modulation scheme, we satisfy the BER and mean spectral efficiency requirements, simultaneously, which is impossible by using the fixed modulation scheme.

• Journal of the Korean Institute of Telematics and Electronics D
• /
• v.36D no.8
• /
• pp.36-44
• /
• 1999

This paper presents the design and fabrication of the duplexer for a Ka-band satellite transponder which is analyzed transmission characteristics by calculating the generalized scattering matrix using mode matching method. It is composed of 2 bandpass filters, coupled with H-plane T-junction having symmetrical inductive iris and E-plane metal insert structures. Compared with the size and weight of the Rx and Tx filter loaded with a transponders respectively, those of the duplexer can be effectively reduced. In a high power transmission, the variation of the filter characteristics is minimized by the scheme that irises are extended to the exterior of H-plane of the waveguide. This scheme needs no extra heat sinks for dissipating high power. The duplexer is designed to improve the simplification, durability and reliability by eliminating tuning screws, which have been used to compensate for the characteristics of fabricated filters. The bandpass filters of the duplexer show the insertion loss of less than 1.2 dB and the return loss in excess of 15 dB. The isolations of more than 65 dB have been achieved between Rx and Tx filter.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.15 no.1
• /
• pp.110-118
• /
• 2004

In this paper, a method is presented for the design of an orthomode transducer(OMT) operating at 21/31GHz frequency bands. A square waveguide is used in the common port while the WR-34 standard rectangular waveguide is used in the straight port. The straight port is connected to the common port via a multi-stage quarter-wave impedance transformer. The side port is coupled to the common port through a slot formed along the center line of the common square waveguide. An impedance transformer is employed to match the impedance of the coupling slot with that of the WR-51 waveguide at the output of the side port. Dimensions of the OMT are iteratively optimized employing the theory of waveguide. The validity of the proposed method is verified by fabricating and testing the designed orthomode transducer.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.2052-2054
• /
• 2004

The TX/RX broadband L-type circular polarization antenna using LTCC at K/Ka band has been presented. This antenna has been analyzed in compensation for LTCC with relative permittivity 5.2 and could have been integrated with RF component. As the measured 10dB impedance circular polarization bandwidth of the proposed antenna is 7%(20.8GHz${\sim}$22.2GHz) at the K band and 2.3%(30.9GHz to 31.6GHz) at the Ka band. Also the gain of the antenna is -0.7${\sim}$3.05dBi at the K band and -2.8${\sim}$1dBi at the Ka band. The purpose of the research is to design an efficient antenna structure for satellite communication at K/Ka band. the antenna should be used for both TX and RX frequency bands. The antenna will be mounted on LTCC(Low Temperature Co-fired Ceramic) so that it can be integrated with other RF circuits. This research is important because of the following reasons. 1) The frequency ranges of satellite communication tends to move up to higher frequency such as Ka band or milimeter wave band. 2) Design of antenna for smaller size, lighter weight and less loss is preferred by most RF engineers. 3) Antennas on LTCC enables to integrate the antenna with other RF circuits, and thus, one can reduce the size and loss of the RF system.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.6
• /
• pp.671-678
• /
• 2014

This paper presents a Ka-band FMCW sensor that has high linearity by improving a nonlinear behavior of the voltage controlled oscillator. Due to the nonlinear characteristics of the voltage controlled oscillator for the conventional method, the drift of beat frequency can cause inaccuracy and errors to the extracted results. A Ka-band FMCW signal with fast transition time could be generated by using both direct digital synthesizer and phase locked loop in this research. The implemented FMCW sensor showed very high accuracy in beat frequency through the test.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.3
• /
• pp.101-109
• /
• 2012

Because the installation problem of parabola antenna that is tilted to 45 degree when this antenna is installed at the area of middle latitude, the study on planar antenna in place of parabola antenna is made rapid progess. Especially, The development of the planar antenna for VSAT is needed depending on the increased Ka-band satellite communications. In this paper, in order to meet with these performances, an array antenna consisting of the vertical polarized waveguide longitudinal slots based on the leaky-wave mode of traveling wave antenna is proposed. Especially, for the lower sidelobe level, the design method of the radiation power distribution control using the different slot widths is proposed. An array antenna consisting of 32 leakywave waveguide antennas is showing 35.16 dBi of gain, 2.5 degree of beamwidth at azimuth, below than -30 dB of sidelobe level, 45.8 degree of beam tilt angle in center frequency 30.2 GHz.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.1
• /
• pp.184-190
• /
• 2006

Using COMS which provides multi-beam switching function, the optimal transmission channel environments which provides the high data rate communication are proposed in this paper. Also the link budget for communication transponder of COMSAT is designed. Bsaed on the channel modeling for group delay, non-linear and gain flatness characteristics, the system performances which provide high data rate (HDR) service were analyzed in Ka-band satellite channel. As the transmission data rate is increased, the degradation due to these channel characteristics is severely affect the system performance. To efficiently provide the various service via the same transmission system it is necessary to equlize the primary impairment factors. The optimum operating points of HDR satellite transmission system are implemeted and operated by considering the analyzed results on channel characteristics.

• Journal of Satellite, Information and Communications
• /
• v.1 no.2
• /
• pp.71-75
• /
• 2006

This paper describes operation plans for satellite communications system (SATCOM) which is consisted of Ka band communication payload, geostationary satellite control system and communication test earth station system for the communication, ocean and meteorological satellite system (COMS). Also this paper describes the communication service and mission plans by each system of the SATCOM, and configurations and functions of the system interface between each system. Especially this paper proposes operational items, functions and their configuration diagrams, touches their operational plans. This paper describes function definitions, configuration diagram and operation plans of the PCS )Payload Control System) for monitor and control of the communication payload and communication service network of the SATCOM.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.17 no.5
• /
• pp.209-215
• /
• 2017

In this paper, an antenna having 2-axes cross monopulse for Ka band millimeter-wave seeker is designed and antenna performance is verified through vacuum-brazing method for fabrication and measurement. Also, by designing and manufacturing a waveguide circulator the antenna including the circulator is measured. Radiating part of the antenna takes optimized slot lengths and offsets from Elliot's array synthesis procedure using the generic algorithm and feeding part for cross monopulse axes uses the folded waveguide to optimize the S-parameter result. Based on this method, the antenna has 33.3 dBi gain, $3.5^{\circ}{\pm}0.5^{\circ}$ beamwidth, below -23 dB SLL through fabricating and measuring. It is found that antenna characteristics is similar to design results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.1
• /
• pp.99-107
• /
• 2014

Abruptly occurred obstacles on highway threaten driving safety. Radar draws the attention to the collision avoidance system because it can be fully operational in all weather, and day and night condition. This paper presents the design, implementation and performance test results of pulsed Doppler radar system for detection and warning of road obstacles. The system is designed to consider highway environment and detection capability about various fixed and moving obstacles. The system consists of 4 subsystems, which include antenna unit, transmitter and receiver unit, radar signal & data processing unit, and controller & display unit. The core technologies include clutter map based change detection for fixed obstacles detection, Doppler estimation for velocity detection of moving targets, and azimuth angle estimation method using monopulse for lane estimation and tracking. The design performance of the developed radar system is verified through experiments using a fixed reference target and moving vehicles in test highway.