• Clean Technology
• /
• v.12 no.1
• /
• pp.1-9
• /
• 2006

Aqueous cleaning agents which are considered to be environmental-friendly and promising alternative ones among various industrial cleaning agents were evaluated in this words. In order to formulate aqueous cleaning agents, primary alcohol ethoxylates with 3, 5 and 7 moles of ethylene oxides among nonionic surfactants were selected as main surfactants. And anionic surfactants and alcohols were chosen as their cosurfactants. Builders such as NaOH, KOH, $Na_2CO_3$ and $NaHCO_3$ were also evaluated as additives for improvement of cleaning efficiency of aqueous cleaning agents. The experimental results of cleaning ability tests show that introduction of anionic surfactant TLS as cosurfactant in alcohol ethoxylate-based aqueous solution gives the best cleaning efficiency for removing mixed soil of cutting oil and grease. NaOH and $Na_2CO_3$ are also shown to play an important role for improvement of cleaning efficiency in a aqueous cleaning agent.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.12
• /
• pp.4316-4320
• /
• 2011

The effects of various hydroxide compounds on base stacking (BS) were investigated for pre-concentration of DNA molecules in capillary electrophoresis (CE). In BS, hydroxide ions ($OH^-$) were electrokinetically introduced after DNA sample injection. A neutralization reaction occurred between the $OH^-$ and $Tris^+$ of the running buffer, which resulted in a zone of lower conductivity. Within the low conductivity zone of the high electric field, the DNA molecules moved more rapidly and were concentrated in front of the low conductivity zone. At the same BS conditions of CE, the enhanced sensitivity of the DNA samples was dependent on the kind of multivalent cations in the hydroxide compounds. Except for LiOH, the hydroxide compounds with monovalent cations showed more effective BS than those with divalent cations because of solubility, ionic strength and electronegativity. The order of hydroxide compounds that enhance the detection sensitivity of DNA molecules was as follows: NaOH > $NH_4OH$ > KOH > $Ba(OH)_2$ > $Sr(OH)_2$ > LiOH > $Ca(OH)_2$ > $Mg(OH)_2$. $NH_4OH$, KOH and $Ba(OH)_2$ proved to be efficient hydroxide compounds to use as effective BS reagents in CE instead of NaOH.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.2
• /
• pp.241-247
• /
• 2012

Many infectious diseases have emerged or re-emerged during the past 50 years in South Korea. There were three outbreaks of foot and mouth disease (FMD) in South Korea between January 2010 and March 2011. Over 3.45 million animals were slaughtered (33.3% of the existing pigs, 8.4% of dairy cows and 3.4% of cattle). To select optimal degradation agents of animal cadavers, degradation rates and fertilizer components of pig cadavers were investigated using hydrogen chloride (HCl), potassium hydroxide (KOH) and sodium hydroxide (NaOH) hydrolysis methods. Degradation rates of pig cadavers using HCl, KOH and NaOH were 81.1, 82.8 and 91.6%, respectively. Total nitrogen (T-N) concentration in degradation solution of pig cadavers using KOH hydrolysis method was higher than that in NaOH and HCl hydrolysis methods. Total phosphorus ($P_2O_5$) concentrations in degradation solution of pig cadavers in all hydrolysis methods ranged 0.14 ~ 0.28%. Total potassium ($K_2O$) concentration for KOH hydrolysis method was higher than that for other hydrolysis methods. The concentration of T-N and $K_2O$ in degradation solution of pig cadavers by KOH hydrolysis method were higher than that in NaOH and HCl hydrolysis methods. Thus, to recycle animal cadavers in agriculture, the optimal degradation agent for hydrolysis was KOH.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.6 no.1
• /
• pp.1-12
• /
• 1998

To examine the possibility of protein recycling of shaving scraps containing chromium generated from manufacturing process of leather, the optimum hydrolysis conditions and the withdrawal methods of low molecular weight protein for using the liquid fertilizer sources by investigation of solubilities of hydrolyzed protein, inorganic nutrients contents and molecular weight distributions of hydrolyzed protein from shaving scraps treated with mixed alkaline inducing agents and mixed alkaline proteolytic enzymes including MgO were investigated. In hydrolysis of shaving scraps treated with mixed alkaline inducing agents, the solubility of shaving scraps were clearly different with 65~85% according to the sorts of the inducing agents, and the degree of hydrolysis was high in the order of NaOH, $Ca(OH)_2$ and KOH. The average molecular weights of withdrawal hydrolyzed protein were 10, 40 and 80 KD treated with NaOH, $Ca(OH)_2$ and KOH, respectively. And the chromium contents was about 15 ppm. In hydrolysis of shaving scraps treated with mixed alkaline proteolytic enzymes, the bility of shaving scraps were high in the order of alcalase, esperase and savinase. In c of treating 0.5% alcalase, the low molecular weight of hydrolyzed protein could be withdrawn. The solubility of the hydrolyzed protein was about 85%, the average molecular weight of the protein was below 1 KD and chrome content of the protein was below 10 ppm.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.7
• /
• pp.2565-2569
• /
• 2010

It was researched the correlation between the Solar cell and the effect of texturing. The samples were textured by using the IPA mixed solution with $HNO_3$, KOH and NaOH. The samples were analyzed by the X-ray Diffraction pattern and Fourier Transform Infrared spectroscopy. The FTIR spectra in the range of 950~1350 $cm^{-1}$ was related to the peak's formation as the bonding structure. The split of peaks means that the inter reaction between the molecular did not activate and then increased the efficiency because of low reflectance as shown the cell treated in NaOH mixed solution.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.16 no.6
• /
• pp.26-33
• /
• 2012

This paper reported on the effect of blended activator on the physical properties of alkali-activated slag mortar. Five different activators(caustic alkalis) were used: sodium hydroxide(NaOH, A Case), calsium hydroxide($Ca(OH)_2$, B Case), magnesium hydroxide($Mg(OH)_2$, C Case), aluminum hydroxide($Al(OH)_3$, D Case), and potassium hydroxide(KOH, E Case). We blended five caustic alkalis with sodium carbonate($Na_2CO_3$). The dosage of five caustic alkalis was 3M and sodium carbonate was 1M, 2M and 3M. The result of flow and setting time was decrease as the dosage of sodium carbonate increase. But the compressive strength was increase as the dosage of sodium carbonate increase. It was shown that there is a good effect of blended caustic alkalis with sodium carbonate in alkali-activated slag mortar.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.24 no.5
• /
• pp.196-201
• /
• 2014

We investigated defects and surface polarity in AlN and GaN by using wet chemical etching. Therefore, the effectiveness and reliability of estimating the single crystals by defect selective etching in NaOH/KOH eutectic alloy have been successfully demonstrated. High-quality AlN and GaN single crystals were etched in molten NaOH/KOH eutectic alloy. The etching characteristics and surface morphologies were carried out by scanning electron microscope (SEM) and atomic force microscope (AFM). The etch rates of AlN and GaN surface were calculated by etching depth as a function of etching time. As a result, two-types of etch pits with different sizes were revealed on AlN and GaN surface, respectively. Etching produced hexagonal pits on the metal-face (Al, Ga) (0001) plane, while hexagonal hillocks formed on the N-face. On etching rate calibration, it was found that N-face had approximately 109 and 15 times higher etch rate than the metal-face of AlN and GaN, respectively. The size of etch pits increased with an increase of the etching time and they tend to merge together with a neighbouring etch pits. Also, the chemical mechanism of each etching process was discussed. It was found that hydroxide ion ($OH^-$) and the dangling bond of nitrogen play an important role in the selective etching of the metal-face and N-face.

• Korean Chemical Engineering Research
• /
• v.48 no.3
• /
• pp.322-326
• /
• 2010

Stability of sodium borohydride solution during storage was studied. In order to enhance the $NaBH_4$ stability, NaOH and KOH were added to the $NaBH_4$ solution. The effect of concentration of the borohydride and alkaline solution, temperature and materials of storage vessels on the rate of borohydride hydrolysis was investigated. The rate of hydrogen evolution decreased as the concentration of alkaline increased due to increase of $NaBH_4$ stability in the solution. The stability of $NaBH_4$ solution decreased when the borohydride concentration raised from 10 to 15 wt% and then increased when the $NaBH_4$ concentration increased above 15 wt% due to increase in the pH of the concentrated solution. The activity coefficient of hydrolysis of $NaBH_4$ solution(NaOH 3.0 wt%, $NaBH_4$ 25 wt%) was 115.1 kJ/mol and this value was 1.5~4.0 times higher than that of hydrolysis of $NaBH_4$ solution with catalyst. The borohydride solutions in glass and stainless-steel vessel were more stable than the solution in plastic(PE) vessel.

• Clean Technology
• /
• v.22 no.4
• /
• pp.274-280
• /
• 2016

In this study, it was to develop a chemical method that can recycle the cutting oil which accounts for about 25% of the cost of the process among containing materials of silicon waste sludge generated in the process for producing a solar cell wafer. The 7 types of reagents have been used, including acetone, HCl, NaOH, KOH, $Na_2CO_3$, HF, $CH_2Cl_2$, etc. for this experiment. And It was carried out at a speed of 3000 rpm for 60 minutes centrifugation after performing a reaction with a waste sludge at various concentrations. As a result, the best reagents and conditions for separating the solid such as a silicon powder and a metal powder and liquid cutting oil were identified as 0.3 N NaOH. It is found to be pH 6.05 in a post-processing recycled cutting oil with 0.3 N NaOH after reaction of waste sludge and 0.1 N HCl which is effective to remove metal powder in order to adjust the pH to suit the properties of the weak acid is a commercially available cutting oil and it showed excellent turbidity than when applied to sludge with 0.3 N NaOH alone. The results of FT-IR analysis which can compare the properties of the commercially available cutting oil shows it has a possibility of recycling oil. The cutting oil recovery rate obtained through the experiment was found to be 86.9%.

• Korean Journal of Soil Science and Fertilizer
• /
• v.45 no.5
• /
• pp.810-816
• /
• 2012

In order to develop liquid fertilizer using rendering by-product, rates and velocities of degradation from rendering by-product using pig cadaver investigated under different amount of injection and time with degradation agents (KOH, NaOH, $HNO_3$ and $H_2SO_4$). The amount of residue by degradation agent of $HNO_3$ treatment method was higher than that in KOH, NaOH and $H_2SO_4$ treatment methods. The degradation velocities (K; $hr^{-1}$) of rendering by-product in KOH treatment method were higher in the order of 25% ($0.0309hr^{-1}$) > 30% ($0.0268hr^{-1}$) > 20% ($0.0142hr^{-1}$) > 15% ($0.0111hr^{-1}$) > 10% ($0.0102hr^{-1}$) of weight of rendering by-product. In all conditions, the degradation velocity of rendering by-product using $H_2SO_4$ 30% of weight of rendering by-product was rapid than that for KOH, NaOH and $HNO_3$ treatment methods. Degradation rates of rendering by-product using NaOH were similar to that of KOH and $H_2SO_4$ except for $HNO_3$ under injecting 25% and 30% of rendering by-product weight.