• Transactions of the Korean Society of Automotive Engineers
• /
• v.14 no.4
• /
• pp.99-106
• /
• 2006

High velocity oxygen-fuel thermal spray coating of the WC-Co cermet material is a well-established process for modifying the surface properties of the structural components exposed to the corrosive and wear attacks, and also these coating are well-known method to improve the fatigue strength of material. In this study, HVOF coated SM490B are prepared to evaluation of the effect of coating on tension and fatigue crack growth behavior. The pre-crack of the fatigue crack growth test specimens machined at deposited material area, heat affected zone and boundary, respectively. Through these test, the following results are obtained: 1) Tensile strength was about 498 MPa, and fracture occurred on base metal area. 2) The fatigue crack of coated specimens propagated more rapidly than non-coated specimen in all specimens. 3) In the same coating thickness specimens, the specimens with pre-crack at boundary more rapidly propagated than the specimens with pre-crack at HAZ and deposited material area. These results can be used as basic data in a structural integrity evaluation of rolled SM490B weldments considering HVOF coating.

• Journal of Korean Society of Steel Construction
• /
• v.29 no.6
• /
• pp.455-465
• /
• 2017

To figure out the weldability and welded joint performance on the FCAW of SM490TMC 120mm, several specimens were manufactured and 10 kinds of experiments were implemented. The result of the weld zone chemical composition test, weld metal tensile test, weld zone tensile test, and weld zone impact test has satisfied the KS. Especially, the weld zone tensile test result shows the base metal fracture, which means the weld zone performs enough required performance. In addition, the results of the weld zone bending test, hardness test, macroscopic test, microscopic test, and the maximum hardness in HAZ were showing that the FCAW weld zone has fine quality.

• Journal of the Korean institute of surface engineering
• /
• v.44 no.1
• /
• pp.21-25
• /
• 2011

This test focuses on the correlation between the lubrication, ductility and strength through the change of nut lubricant which decides joining angle for A490 bolt sets required in the AASHTO (American Association of State Highway & Transportation Officials). Because the lubrication of high tension bolt, nut, washer sets becomes an important factor to ductility and joining load, the quality improvement is required for improving reliability and securing enough lubrication of maker and user. This study examines the quality characteristics required in the specification through tests because only this standard specifies joining quality in the extreme conditions (as much about two times of the joining angle on site as normal condition). Moreover, this study is limited to the test on joining axial force required in the AASHTO for the three nut lubrication conditions of A490 bolt set. It is concluded that the nuts should be coated or waxed enough for the improvement of the joining axial force and ductility of bolts required in the standards. It is shown that in the case of plain high tension bolt sets, a rust preventing lubricative oil shall be applied and the torque coefficient value for A490 bolt sets should be maintained below 0.175.

• The Korean Journal of Ecology
• /
• v.9 no.4
• /
• pp.185-192
• /
• 1986

The production and decomposition rate of litters from the three different locations, Quercus acutissium forest at 630 m, Q. mongolica forests at 1, 005m and 1, 490 m of Mt. Dokyoo, were estimated by Olson model. The contents of N, P, K, Ca and Na in soils were measured and the relationships among them were elucidated. The amounts of litter production in Q. mangolica were the lowest, 378.96g/$m^2$ at 1, 490 m and the highest, 876.12g/$m^2$ at 1, 005 m. And the amounts of litter production in Q. acutissima at 630 m was 686.16 g/$m^2$. The decay rate of litters in Q. mongolica was the smallest, 0.123 at 1, 490 m, and the largest, 0.222 at 1, 005 m. And that in Q. acutissima was 0.169 at 630 m which was the medium rate. The production and decay rate of litters decreased with the ascending altitude. The values at 630 m were maller than those at 1, 005 m. This might be due to the fact that the tree species at 630 m was Q. acutissima was 0.169 at 630 m which was the medium rate. The production and decay rate of litters decreased with the ascending altitude. The values at 630 m was Q. acutissima which was different from Q. mongolica at 1, 005 m and 1, 490 m. The half-0life of litter decay in Q. monglica was 5, 634 years at 1, 490 m and 3.134 years at 1, 005 m. And that in Q. acutissima was 4.132 years at 630 m. The decay rates of litters were tend to be inversely proportional to the ascending altitude. The annual standing stocks of mineral and their amounts returned to the soil were proportional to the decay rate of organic matters.

• Proceedings of the Korean Institute of Communication Sciences Conference
• /
• 2006.07a
• /
• pp.490-490
• /
• 2006

• 한국생물공학회:학술대회논문집
• /
• 2005.10a
• /
• pp.490-490
• /
• 2005

• Proceedings of the KWS Conference
• /
• 1997.10a
• /
• pp.147-150
• /
• 1997

The characteristics of underwater welding of SWS490 steel were investigated. The bead-on-plate type welding with one or three pass using ilmenite and water-proofed type electrodes was performed by varying welding currents and the sizes of electrodes used. The amounts of hydrogen absorbed inter the weld metal were measured according to the JIS Z 3118 specification and the results were interpreted in terms of the cold cracking behaviours of the welded steel. The microstructural changes as well as the microhardness distribution after underwater welding were also investigated using Vickers microhardness tester and S.E.M (scanning electron microscopy) and O.M (optical microscopy). The results indicated that the cold cracking could be avoided by three pass welding under low current with an electrode with a small diameter.

• Journal of Plant Biotechnology
• /
• v.41 no.1
• /
• pp.56-63
• /
• 2014

Using commercial radish varieties for processing, about 30% of radish was discarded due to the root shape and low purity. To raise the processing ability, we tried to develop a new variety producing H-shaped root. As another characteristic required in variety for processing is high purity, we tried to raise purity using simple sequence repeats (SSR) markers for testing seed purity in every segregating generation. To develop Male-sterile (MS) seeding parent, we crossed commercial variety of 'Gwan dong spring' and 'Gyeo ryong spring'. One elite inbred was selected as recurrent parent for the MS plant. The major horticultural traits of selected inbred line were disease resistance, late bolting, heat resistance and bright green root top color. To develop pollen parent, we crossed commercial variety of 'Tae sang king' and 'Seoul spring'. We used individual selection method to develop H-shaped hard root and disease resistant inbred. In each segregating generation, we selected one plant based on phenotype and the uniformity of selected plant was tested by SSR markers using self-pollinated seeds. In the first segregating generation, 64.6% of sib plants shared the same band in PCR amplification using ACMP-490 primer and 66.7% using cnu-316 primer. The uniformity of segregating generations using ACMP-490 and cnu-316 raised in second generation to 68.8%, 70.8%, respectively; in third generation to 93.8%, 100%; in fourth generation to 93.8%, 100%; in fifth generation to 95.8%, 100%; in sixth generation to 100%, 100%. A novel cross was made using selected MS parent and pollen parent. When we checker the horticultural traits using autumn cultivation, the novel cross variety produced H-shaped root comparing other commercial varieties and produced highly uniform radish. Thus we registered this novel cross variety as 'YR ORE' at 2013 (Registration No. 4550).

• Journal of the Korean Chemical Society
• /
• v.58 no.5
• /
• pp.490-495
• /
• 2014

• Fire Science and Engineering
• /
• v.27 no.5
• /
• pp.1-7
• /
• 2013

Fire at building can occur enormous damages to life, properties, and environment and the risk of fire breakout is going up higher because of application of combustible materials than before. Therefore, the steel industries are trying to develop fire resistant steel in order to sustain the load bearing capacity of steel structures during fire situation. In this paper, to give the basis data-bases for evaluation of structural stability of steel structures applied fire resistant steel, FR 490, the tests of mechanical and thermal properties at high temperature were conducted and the comparisons are done with the SM 490 that has the same mechanical one.