• Journal of The Korean Society of Agricultural Engineers
• /
• v.56 no.4
• /
• pp.21-28
• /
• 2014

In this study, evaluated ware the strength and durability of the vegetated water purification channel concrete to which recycled aggregates, hawang-toh and jute were applied. Box-Behnken method of response surface analysis in statistics was applied to the experimental design. Experimental variables are as follows, recycled coarse aggregates, hawang-toh, blast-furnace slag and jute fiber. In the experiment, conducted were the tests of compressive strength, chloride ion penetration, abrasion resistance and impact resistance the replacement rate effects of the recycled aggregates, blast-furnace slag and hwang-toh on the performance of vegetated water purification channel concrete were analyzed by using the response surface analysis method on the basis of the experimental results. In addition, an optimum mixing ratio of vegetated water purification channel concrete was determined by using the experimental results. The optimum mixing ratio was determined to be in 10.0% recycled coarse aggregates, 60.0% blast-furnace slag, 10.1% hwang-toh and 0.16% jute fiber. The compressive strength, chloride ion penetration, abrasion rate, and impact number of fracture test results of the optimum mixing ratio were 24.1 MPa, 999 coulombs, 10.30 g/mm3, and 20 number, respectively.

• BMB Reports
• /
• v.36 no.5
• /
• pp.427-432
• /
• 2003

Jute is the principal coarse fiber for commercial production and use in Bangladesh. Therefore, the development of a high-yielding and environmental-stress tolerant jute variety would be beneficial for the agro economy of Bangladesh. Two molecular fingerprinting techniques, random-amplified polymorphic DNA (RAPD) and amplified-fragment length polymorphism (AFLP) were applied on six jute samples. Two of them were cold-sensitive varieties and the remaining four were cold-tolerant accessions. RAPD and AFLP fingerprints were employed to generate polymorphism between the cold-sensitive varieties and cold-tolerant accessions because of their simplicity, and also because there is no available sequence information on jute. RAPD data were obtained by using 30 arbitrary oligonucleotide primers. Five primers were found to give polymorphism between the varieties that were tested. AFLP fingerprints were generated using 25 combinations of selective-amplification primers. Eight primer combinations gave the best results with 93 polymorphic fragments, and they were able to discriminate the two cold-sensitive and four cold-tolerant jute populations. A cluster analysis, based on the RAPD and AFLP fingerprint data, showed the population-specific grouping of individuals. This information could be useful later in marker-aided selection between the cold-sensitive varieties and cold-tolerant jute accessions.

• Advanced Composite Materials
• /
• v.16 no.4
• /
• pp.385-394
• /
• 2007

In this study, the effect of molding condition on the tensile properties for plain woven hemp fiber reinforced green composite was examined. The tensile properties of the composite were compared with those of the plain woven jute fiber composite fabricated by the same process. Emulsion type biodegradable resin or polypropylene sheet was used as matrix. The composites were processed by the compression molding where the molding temperature and its heating time were changed from 160 to $190^{\circ}C$ and from 15 to 25 min, respectively. The following results were obtained from the experiment. The tensile property of hemp fiber reinforced polypropylene is improved in comparison with polypropylene bulk. The strength of composite is about 2.6 times that of the resin bulk specimen. Hemp fiber is more effective than jute fiber as reinforcement for green composite from the viewpoint of strength. The molding temperature and time are suitable below $180^{\circ}C$ and 20 min for hemp fiber reinforced green composite. Hemp fiber green composite has a tendency to decrease its tensile strength when fiber content is over 50 wt%.

• Journal of Adhesion and Interface
• /
• v.7 no.2
• /
• pp.26-31
• /
• 2006

In order to effectively improve interfacial adhesion strength between polypropylene (PP) and jute fiber, we particularly incorporated maleic anhydride grafted PP (MAPP) into the matrix through the environment-friendly process without an additional method of process and had better mechanical performances by providing the alignment into the natural fiber than those of the conventional fabrication technology such as an extrusion or injection molding. We also proposed hot pressing method which applied relatively low shear to the composites and confirmed the chemical bonds among the functional groups of MAPP and jute using FT-IR approach. The concentration of MAPP for maximum tensile strength and modulus was optimized at 3 wt%. Flexural properties had no noticeable tendency to increase with MAPP contents compared to tensile strength, which could probably be explained by the degree in wetting of PP/MAPP matrix.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.157-160
• /
• 2005

The surface energies and acid-base interaction between the untreated and treated Jute or Hemp fibers and different matrix compositions of polypropylene-maleic anhydride polypropylene copolymers (PP-MAPP) were investigated using dynamic contact angle measurement. The contribution of the acid-base property into the interfacial adhesion of the natural fibers/matrix systems were characterized by calculating the work adhesion coming from the acid-base interaction. On the other hand, microfailure mechanism of both single Jute and Hemp fiber bundles were investigated using the combination of single fiber tensile test and acoustic emission. Distinctly different micro failure modes of the different natural fiber/polypropylene systems wet ε observed using optical microscope and determined indirectly by AE and their FFT analysis.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.55 no.3
• /
• pp.25-33
• /
• 2013

In this study, the optimum mix proportions of rain garden structure concrete were decided and the mechanical properties were evaluated. Experimental parameters were blast furnace slag, hwang-toh, recycled aggregates and natural jute fibers. The target compressive strength and chloride ion penetration were more than 24 MPa and less than 1000 coulombs, respectively. The response surface method was used for statistical optimization of experimental results. The optimal mixing ratios of the blast furnace slag, hwang-toh, recycled coarse aggregate and jute fiber volume fraction were determined 59.98 %, 8.74 %, 12.12 % and 0.2 %, respectively. The compressive strength, flexural strength and chloride ion penetration test results of optimum mix ratio showed that the 24.56 MPa, 3.88 MPa and 999.08 columbs, respectively.

• Structural Engineering and Mechanics
• /
• v.76 no.5
• /
• pp.613-618
• /
• 2020

Exhausting oil resources and increasing pollution around the world are forcing researchers to look for new, renewable, biodegradable materials to lead sustainable development. The use of fiber reinforced composites based on natural fibres has increasingly begun as prospective materials for various engineering applications in the automotive, rail, construction and aerospace industries. The natural fiber chosen to make the composite material is plant-based fibre, e.g. jute fibre, and hemp fibre. Thermosetting polymer based Epoxy (LY556) was utilized as matrix material and The composites were produced using hand lay-up technique. The fabricated composites were tested for acoustic testing, thermo-gravimetric analysis (TGA) and flammability testing to asses sound absorption, thermal decomposition and fire resistivity of the structures. Hemp fibre composites have shown improved thermal stability over Jute fibre composites. However, the fire resistance characteristics of jute fibre composites are better as compared to hemp fibre composites. The sound absorption coefficient of composites was found to enhance with the increase of frequency.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.36 no.5 s.108
• /
• pp.29-35
• /
• 2004

Fiber dimensions, their derived values and chemical properties of cotton stalks (Gosypium hirsutum L), jute stick (Corchorus capsularis) and dhancha (Sesbania aculeate) have been examined to assess their suitability for paper production. Cotton stalks have a good derived values especially slender ratio, which is comparable to hardwood. The flexibility coefficient of these three non wood plants is better than hardwood. Anatomical analysis shows higher percentage of fibers and vessels than in general non wood plants. Lignin, $\alpha$-cellulose and pentosan contents in these three nonwood plants are within the range of hardwood. Neutral sugar analysis of cotton stalks, jute stick and dhancha shows that the glucose in the major sugar followed by xylose and mannose. The arabinose and galactose are present in minor amount. Alkaline nitrobenzene oxidation of cotton stalks, jute stick and dhancha wood meal exhibits that these nonwood plant lignins mainly consist of syringyl (S) and guaiacyl (V) units. The S/V ratios are 1.6, 1.2 and 2.1 for cotton stalks, jute stick and dhancha, respectively.

• Journal of the Korea Institute of Building Construction
• /
• v.11 no.5
• /
• pp.419-425
• /
• 2011

Topping concrete that is not reinforced with rebar to prevent poor tensile performance is vulnerable to cracking. In this study, jute, which is known to be an excellent natural fiber material for strengthening concrete performance, was compared with other cellulose fibers in terms of its capacity to reduce the cracking of concrete. As a result, it was found that compared with concrete using other fibers, concrete using jute fiber showed more than a 50 % reduction of plastic shrinkage crack resistance with the contents of 0.9 kg/$m^3$ and 1.2 kg/$m^3$ for. For impact strength tests, the final destruction of WF and PULP fibers took up to 5 times the number of falls, while jute has 10-18 circuitry, showing excellent ductility properties.

• Structural Engineering and Mechanics
• /
• v.74 no.4
• /
• pp.515-520
• /
• 2020

In the modern era, the world is facing unprecedented challenges in form of environmental pollution and international agencies are forcing scientists and materialists to look for green materials and structures to counter this problem. Composites based on renewable sources like plant based fibres, vegetable fibres are finding increasing use in interior components of automobile vehicles, aircraft, and building construction. In the present study, jute and flax fibre based composites were developed and tested for assessing their suitability for possible applications in interior cabin and parts of automobile and aerospace vehicles. Matrix system involves epoxy as resin and fibre weight fractions used were 45% and 55% respectively. Composites samples were prepared as per American society for testing and materials (ASTM) standard and were tested for individual fiber tensile strength, composite tensile strength, and flexural strength to analyse its behavior under various loading conditions. The results revealed that the Jute fibre composites possess enhanced mechanical properties over Flax fibre composites.