• 콘크리트학회지
• /
• 제6권2호
• /
• pp.138-147
• /
• 1994

대형 콘크리트 판넬구조 수평접합부는 상부로부터 전달되는 축하중에 대하여 저항하게 되며 이때의 저항내력은 그라우트와 판넬의 강도, 접합부의 형태 및 단부 모멘트, 그라우트의 폭 등에 따라 변하게 된다. 본 연구는 패쇄형 수평접합부에 대한 실험연구로서 슬래브의 단부형태, 벽판넬의 단부보강 및 슬래브의 횡변위 구속에 따른 내력의 변화를 관찰하고자 하였다. 현재 대형 콘크리트 패널구조 수평접합부의 설계에 적용되고 있는 국내 규준식은 국내의 대형 콘크리트 패널구조와는 다소 다른 형태의 실험결과에 의해 유도된 식으로서 그 적용성에 대한 평가가 요망된다. 따라서 본 연구에서는 실험결과를 근거로 이에 대한 평가를 실시할 뿐만 아니라 폐쇄형 수평접합부의 내력을 평가할 수 있는 적합한 이론식을 제시 하였다. 실험결과, 상부 벽판넬의 단면이 결손(10mm)됨에 따라 약 23.5% 내력이 저감되는 것으로 나타났으며, 슬래브 단부형태의 따른 차이와 벽판넬의 단부보강에 따른 내력의 차이, 슬래브의 횡변위 구속 유무에 따른 내력의 차이는 거의 없는 것으로 나타났다. 또한, 제안되 이론식과 실험결과를 비교한 결과 이론식에 의한 결과가 실험결과와 좋은 대응을 보이는 것으로 나타났다.

• Journal of the Korean Wood Science and Technology
• /
• 제24권1호
• /
• pp.95-99
• /
• 1996

The bending and compression strength properties of two types Rhus verniciflua specimens, which made of no heat-treated wood and heat-treated wood for urushiol extraction, were measured. The heat-treated specimens were finger-jointed with either resorcinol-phenol or polyurethane resin adhesives, and the vertical type bending strength property was also measured in these specimens. The results obtained are as follows ; 1. The correlation coefficient between the compression strength and specific gravity in the specimens of no heat-treated and heat-treated wood was high. However there was no difference in compression strength property as affected by heat treatment. 2 The correlation coefficient between the bending strength and specific gravity in the specimens of no heat-treated and heat-treated wood was also high. However, there was no difference in bending strength property as affected by heat treatment. 3 The bending test showed high correlation between modulus of elasticity and modulus of rupture for the specimens made of no heat-treated and heat-treated wood. However, there was no difference in bending strength property between the specimens made of heat-treated and no heat-treated wood. 4. The efficiencies of bending strength test on the finger-jointed specimens of heat-treated wood with resorcinol-phenol and polyurethane resin adhesives were 0.85, 0.81. respectively.

• 한국생산제조학회지
• /
• 제21권6호
• /
• pp.1018-1023
• /
• 2012

In order to substitute and recycle the existing automobile parts for GMT-sheet, researches on the effects of GMT-sheet on the establishment of precise joining strength, joining condition that are lap length of joining part, compression ratio, and closure speed must be carried out but until now. Besides, many researches on adhesion joint had been conducted until now but no systematic research on press lap joint of GMT-sheet has been implemented until recently and the reliability of joining strength is not yet established. In press lap joining molding of GMT-sheet, tensile stress and lap joining connection efficiency was increased according to the increase of lap length L. However, as the increase of compression ratio and fiber content ratio per unit area was higher in tensile test, it has caused the deterioration of lap joining efficiency after joining molding of GMT-sheet. Clarify joining strength and lap joining efficiency during high temperature compression press lap joining molding of GMT-sheet and research data regarding to the lap length of joining part was presented. The purpose of this study is to contribute to the substitution of existing products as well as usage development in non-automobile field and also to find out precise dynamic characteristics as designing data of structures.

• Computers and Concrete
• /
• 제23권6호
• /
• pp.377-398
• /
• 2019

Behavior of RC beam-column joint is very complex as the composite material behaves differently in elastic and inelastic range. The approaches generally used for predicting joint shear strength are either based on theoretical, strut-and-tie or empirical methods. These approaches are incapable of predicting the accurate response of the joint for entire range of loading. In the present study a new generalized RC beam-column joint shear strength model based on hybrid approach i.e. combined strut-and-tie and empirical approach has been proposed. The contribution of governing parameters affecting the joint shear strength under compression has been derived from compressive strut approach whereas; the governing parameters active under tension has been extracted from empirical approach. The proposed model is applicable for various conditions such as, joints reinforced either with or without shear reinforcement, joints with wide beam or wide column, joints with transverse beams and slab, joints reinforced with X-bars, different anchorage of beam bar, and column subjected to various axial loading conditions. The joint shear strength prediction of the proposed model has been compared with 435 experimental results and with eleven popular models from literature. In comparison to other eleven models the prediction of the proposed model is found closest to the experimental results. Moreover, from statistical analysis of the results, the proposed model has the least coefficient of variation. The proposed model is simple in application and can be effectively used by designers.

• Geomechanics and Engineering
• /
• 제23권6호
• /
• pp.587-600
• /
• 2020

Shear-induced instability of jointed rock mass has greatly threatened the safety of underground openings. To better understand the failure mechanism of surrounding rock mass under shear, the flawed specimens containing a circular opening and two open joints are prepared and used to conduct direct shear tests. Both experimental and numerical results show that joint inclination (β) has a significant effect on the shear strength, dilation, cracking behavior and stress distribution around flaws. The maximum shear strength, occurring at β=30°, usually corresponds to a unifrom stress state around joint and an intense energy release. However, a larger joint inclination, such as β=90°~150°, will cause a more uneven stress distribution and a stronger stress concentration, thus a lower shear strength. The stress distribution around opening changes little with joint inclination, while the magnitude varys much. Both compression and tension around opening will be greatly enhanced by the 30°-joints. In addition, a higher normal stress tends to enhance the compression and suppress the tension around flaws, resulting in an earlier generation and a larger proportion of shear cracks.

• 콘크리트학회논문집
• /
• 제15권2호
• /
• pp.297-304
• /
• 2003

본 연구에서는 철근콘크리트 기둥과 철골보로 구성된 혼합 골조구조의 접합부에 대한 구조적 특성을 평가하였다. 주요변수로는 본 연구에서 제안한 자주식(子株式) 횡보강근 상세와 기존의 RCS 공법에서 사용되고 있는 ㄱ-4조각 조합형 및 용접형 등의 횡보강근 상세를 대상으로 하였다. 실험체는 총 5개의 내부접합부를 대상으로 2/3 축소로 제작하여 접합부의 전단 및 내진성능을 평가하였다. 실험의 결과, 모든 실험체에서 최대내력 이후 강도 및 강성의 큰 저하없이 실험이 종료되었다. 따라서, 자주식(子株式) 횡보강근을 사용한 RCS 접합부의 구조성능은 4조각 조합형 및 용접형 등의 기존 공법과 동등 이상의 구조적 성능을 확보하는 것으로 나타나 외부 판넬의 전단기여도는 압축스트러트에 의해 평가하는 것이 보다 적절할 것으로 판단된다.

• Steel and Composite Structures
• /
• 제10권5호
• /
• pp.385-414
• /
• 2010

In current European Standard EN 1993, the moment-rotation characteristics of beam-to-column joints made from steel with a yield stress > 460MPa are obtained from elastic design procedures. The strength of the joint basic components, such as the column web subject to local transverse compression, is thus limited to the yield resistance rather than the plastic resistance. With the recent developments of higher strength steel grades, the need for these restrictions should be revisited. However, as the strength of the steel is increased, the buckling characteristics become more significant and thus instability phenomena may govern the design. This paper summarizes a comprehensive set of finite element parametric studies pertaining to the strength behaviour of high-strength steel unstiffened I-columns in transverse compression. The paper outlines the implementation and validation of a three-dimensional finite element model and presents the relevant numerical test results. The finite element predictions are evaluated against the strength values anticipated by the EN 1993 for conventional steel columns and recommendations are made for revising the specifications.

• 대한물리치료과학회지
• /
• 제15권4호
• /
• pp.35-42
• /
• 2008

Background : To assess the effect of a pelvic compression belt on the strength of hip flexor in healthy young individuals. Study design: Pre- and post-treatment measurement design on one factor was used. Methods : 30 healthy volunteers (male: 15, female: 15) participated in this study. Dynamometer was used to measure the strength of hip flexor, and measurements were performed before and after the application of the pelvic compression belt at neutral position of hip joint and at 30 cm raised position from floor with straight leg in supine. Results : After the application of the pelvic compression belt, the strengths of hip flexor measured at both positions were significantly increased when compared with before the application (p<.05). However, at neutral position of hip joint and at 30cm raised position from floor, there were significantly different in the changing patterns in the strengths of hip flexor between men and women (p>.05). Conclusion : The findings suggest that the pelvic compression belt is helpful in strengthening hip muscles. With easy application, it is sufficiently feasible for clinical use.

• 한국강구조학회 논문집
• /
• 제22권5호
• /
• pp.435-443
• /
• 2010

현행 송전강관철탑의 경우 허용응력 설계개념을 도입한 철탑설계기준을 적용하여 설계, 제작되고 있다. 이 철탑설계기준의 압축재의 설계 강도 결정은 압축재의 허용좌굴응력에 의하여 결정되고 있으나 이는 접합부의 내력을 고려치 않은 값이다. 부재가 압축좌굴내력에 도달하기 전에 접합부의 변형으로 인하여 국부변형에 의한 접합부 파괴가 발생할 수 있다. 따라서 본 연구에서는 접합부의 보강형태별로 접합부내력을 산출하고 이를 데이터베이스화한 후 지난 연구에서 도출한 등가비선형해석기법의 부재내력과의 상호 비교를 통하여 부재파괴와 접합부파괴의 선행 여부를 판별할 수 있는 실용적인 평가 및 설계 기법을 제시하였다.

• 한국추진공학회지
• /
• 제1권1호
• /
• pp.111-121
• /
• 1997

본 연구에서는 탄소/에폭시 복합재료의 기계적 결합부위의 결합강도 예측을 위한 구조해석과 실험을 수행하였다. 복합재료 구조물의 Joint설계에 있어 베어링 파괴는 대단히 중요한 파괴형태 중하나이다. 그래서 본 연구에서는 베어링 파괴를 해석적으로 예측하고 실험적으로 확인하였다. 순수인장 파괴(Net Tension Failure)와 베어링 파괴(Bearing Failure) 실험을 위해서 각각 두 가지 형상의 시편을 선택하였다. 기계적 결합강도 예측에 사용된 방법은 특성길이(Characteristic Length)법과 연관시킨 Yamada-Sun 파괴기준(Failure Criterion)과 Tsai-Hill 최대일 이론이다. 그리고 인장특성길이와 압축특성길이는 실험을 통하여 얻어지며, 특히 압축특성길이 결정은 최근에 착안된 베어링파괴 실험으로부터 결정하였다. 위와 같은 예측 방법을 준등방성(Quasi-Isotropic) Carbon/Epoxy HT245/RS3232에 적용하였다. 연구결과, 이론적인 복합재료 파괴예측이 실험결과와 잘 일치함을 확인할 수 있었다.