• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.05a
• /
• pp.517-520
• /
• 2008

Recently, use of adhesive bonding technology is increased to achieve the multi-material design for lightweight structure in automobile industry. In this paper, the fracture strength of adhesive has been studied with the single lap shear test conducted at different temperatures. The joint specimens are made from Al 5052 and SPRC 440 bonded with structural epoxy adhesive. The operating temperature has been considered up to $150[^{\circ}C]$ and the single lap shear test has been conducted with 5mm/min tensile rate. Fracture strength of adhesive bonded joint has been decreased with increase of operating temperature. The fracture strength at the $100[^{\circ}C]$ was shown about half of that at room temperature.

• Journal of muscle and joint health
• /
• v.5 no.2
• /
• pp.222-237
• /
• 1998

In an attempt to investigate the effect of long-term aquatic exercise program on lower limbs' muscle strength, knee Joint flexion, pain reduction and weight changes with aquatic exercise program. Forty three women with arthritis were pre and post tested for changes of muscle strength, range of motion, weight and pain. This data was collected from April 1, 1997 to February 24, 1998. The mean age was 52.5. Statistically significant in lower limbs' muscle strength with an aquatic exercise program by age, BMI, education, rheumatic drug use, illness duration until 12 weeks after experiment. Statistically significant in knee joint flexion with aquatic exercise program by age, BMI, education, rheumatic drug use, illness duration until 12 weeks after experiment. Statistically significant in pain reduction with aquatic exercise program by age, BMI, education, rheumatic drug use, illness duration until 12 weeks after experiment. Statistically significant in weight changes with aquatic exercise program by age, BMI, education, rheumatic drug use, illness duration until 6 weeks after experiment. As a conclusion, aquatic exercise programs for the patients with arthritis require at least 12 weeks and a variety of aquatic exercise programs for the effective control should be developed.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.1039-1044
• /
• 2003

Adhesive-bonded joints are widely used in the industry. Recently aircraft applications of adhesive bonding joints have been increased extensively in automobile and air industry. Because adhesives which are available for structural applications have been developed a lot and understanding of adhesive bonding has been improved so much. In this study, as the fundamental research of design of adhesive bonding joints, this study considers specimen shape are affect strength and durability of Al/Polymer lap joints. In this research, cross head speed difference were concerned to evaluate their effects on the adhesive strength. Cross head speed makes a change 0.05mm/min, 0.5mm/min, 5mm/min. The result is load-displacement diagram showed brittleness fracture tendency. Fracture tendency that is shown enough on stress distribution of trigonal single lap joint and trigonal edged single lap joint occur the inside of adhesive.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.43 no.6
• /
• pp.113-119
• /
• 2001

Experiments on the yield strength of pipe connectors made of metal wire, joint pins, pole pipes, multi span insertion joints, and T-clamp joints used in pipe houses were conducted. The strength of connections of a pipe connector made of metal wire was adequate but it had a big difference according to loading direction. Therefore as it is installed, its direction should be taken into consideration. The collapse load of pipes connected with a joint pin was lower than that of single pipes. In the part of frame member at which the great bending moment occurs, the use of joint pin should be avoided. Also experimental results showed that pole pipes for use in a part of frame buried under the ground were safe, and the strength of multi span insertion joints should be increased. The resistant moment of T-clamp was about 13.7% of a single pipe. In case that the external forces acting on left and right rafter are different. a unsymmetrical rotational force is produced at the multi span joint. If it is expected that the actual bending moment on the multi span joint is larger than resistant moment of T-clamp, a reinforcement to safely resist the rotational force is required.

• International Journal of Automotive Technology
• /
• v.6 no.5
• /
• pp.519-527
• /
• 2005

Recently, weight reduction of vehicles has been of great interest and consequently the use of low-density materials in the automotive industry is increasing every year. However, the substitution of one material for another is not simple because it accompanies several problems, for example, weakness in the strength and stiffness and difficulty in the joining. To overcome these problems, the structure of the automobile redesigned totoally. Aluminum spaceframe is rapidly being adopted as a body structure for accommodating lightness, stiffness and strength requirement. In aluminum spaceframe manufacturing, it is often required to join aluminum tube. However, there are few suitable methods for joining aluminum tube, so that much interest has been focused on testing suitable joining methods. Joining by electromagnetic forming (EMF) can be useful method in joining aluminum tube, which offers some advantages compared with the conventional joining methods. In this paper, joining by EMF was investigated as a pre-study for applying an automotive spaceframe. Finite element simulations and strength tests were performed to analyze the influence of geometric parameters on joint strength. Based on these results, configurations of axial joint and torque joint were suggested and guidelines for designing EMF joint were established.

• Earthquakes and Structures
• /
• v.25 no.3
• /
• pp.149-160
• /
• 2023

Over the course of the last 4-5 years, India's northeastern region have widely used Autoclaved Aerated Concrete (AAC) blocks to construct load-bearing masonry structures. The aim of this investigation is to examine the shear characteristics of AAC masonry triplet assemblage strengthened by using two techniques, i.e., the bead joint (BJ) and the bed-head joint (BHJ) technique. Three unique variations of wire mesh were involved in the strengthening method. Furthermore, three strengthening configurations were used to strengthen each of the three wire mesh variations and the two-strengthening method, i.e. (-), L and (Z) configuration. The unreinforced and reinforced triplet masonry wallets were tested under direct shear test. From the results obtained, the 'BJ'triplet masonry wallets observed an enhanced in shear strength of about 2.23% to 23.33 % whereas the 'BHJ' triplet masonry wallets observed an enhanced in shear strength of about 22.92% to 50.69%. The "BHJ" strengthening method effectively enhance the shear strength of the triplet masonry wallets compared to the "BJ" and the "UR" wallets with an increase in capacity as the wire mesh strength increases. Furthermore, in terms of the strengthening configuration, the (Z) configuration performs better, followed by the (L) and (-) configuration demonstrating the strengthening configuration effectiveness.

• Computers and Concrete
• /
• v.34 no.1
• /
• pp.15-31
• /
• 2024

This study explores the failure mechanisms of 'I' shaped non-persistent cracks under uniaxial loads through a combination of experimental tests and numerical simulations. Concrete specimens measuring 200 mm×200 mm×50 mm were manufactured, featuring 'I' shaped non-persistent joints. The number of these joints varied from one to three, with angles set at 0, 30, 60, and 90 degrees. Twelve configurations, differing in the placement of pre-existing joints, were considered, where larger joints measured 80 mm in length and smaller cracks persisted for 20 mm with a 1 mm crack opening. Numerical models were developed for the 12 specimens, and loading in Y-axis direction was 0.05 mm/min, considering a concrete tensile strength of 5 MPa. Results reveal that crack starting was primarily influenced by the slope of joint that lacks persistence in relation to the loading direction and the number of joints. The compressive strength of the samples exhibited variations based on joint layout and failure mode. The study reveals a correlation between the failure behavior of joints and the number of induced tensile fracture, which increased with higher joint angles. Specimen strength increased with decreasing joint angles and numbers. The strength and failure processes exhibited similarities in both laboratory testing and numerical modeling methods.

• Journal of International Academy of Physical Therapy Research
• /
• v.2 no.1
• /
• pp.229-236
• /
• 2011

The purpose of this study was to comparatively analyze the active stability of shoulder joints according to the frequency of overhead motions, such as serving and spiking, engaged in by female professional volleyball athletes who play different positions, and to provide the results as the basic data for developing exercise programs to prevent shoulder joint injuries. The subjects of this study were 50 Korean female professional volleyball players and positions were as follows: left and right attackers, centers, setters, and liberos. The external rotation and internal rotation muscle strength and muscle strength ratios of the dominant and non-dominant arms of all subjects were measured using Biodex. The results of this study are as follows: Frist, no significant differences were found in the internal and external rotation muscle strength of the dominant and non-dominant arms between positions. Second, for the shoulder joint muscle strength ratio of the dominant arm, by position, the setter showed significantly greater stability compared to the other positions. Third, for the shoulder joint muscle strength ratio of the non-dominant arm, by position, no significant difference in stability between positions was found. Fourth, it was found that the dominant arm had significantly greater instability of the shoulder joint than the non-dominant arm for attackers and centers, but no significant difference was found for setters and liberos. This study comparatively analyzed the muscle strength ratios of the external/internal rotations and dominant/non-dominant arms, which can determine the stability of the shoulder joints between female professional volleyball playing positions that engage in jumps and spikes using only the dominant hand and positions that do not.

• International Journal of Advanced Culture Technology
• /
• v.3 no.1
• /
• pp.61-67
• /
• 2015

The application of SS400 carbon steel and AISI430 ferritic stainless steel joint has been increased in industries because of the advantage of both metals was able to increase the service lifetime of the important structures. Therefore, a fusion welding process that could produce a sound weld and good joint properties should be optimized. This research is aimed to weld a butt joint of SS400 carbon steel and AISI430 ferritic stainless steel using Gas Metal Arc Welding (GMAW) welding process and to study the effects of welding parameters on joint properties. The experimental results were concluded as follows. The optimized welding parameter that produced the tensile strength of 448 MPa was the welding current of 110A, the welding speed of 400 mm/min and the mixed gas of $80%Ar+20%CO_2$. Increase of the welding current affected to increase and decrease the tensile strength of the joint, respectively. Lower welding current produced the incomplete bonding of the metals and indicated the low tensile strength. Microstructure investigation of the welded joint showed a columnar grain in the weld metal and a coarse grain in the heat affected zone (HAZ). The unknown hard precipitated phases were also found at the grain boundaries of the weld metal and HAZ. The hardness profile did not show the difference of the hardness on the joint that was welded by various welding currents but the hardness of the weld metal was higher than that of the other location.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.23 no.2
• /
• pp.93-106
• /
• 2021

In general, segment lining tunnel refers to a tunnel formed by connecting precast concrete segments as a ring and connecting such rings to each other in the longitudinal direction of the tunnel. As the structural properties of the segment lining is highly dependent on the behavior of the segment joints, thus correct modelling of joint behavior is crucial to understand and design the segment tunnel lining. When the tunnel is subjected to ground loads, the segment joint behaves like a hinge that resists rotation, and when the induced moment exceeds a certain limit of the rotation then it may enter into non-linear field. In understanding the effect of the segment joint on the lining behavior, a moment-rotation relationship of the segment joint was explored based on the Japanese practice and Janssen's approach commonly used in the actual design. This study also presents a method to determine the rotational stiffness of joint refer to the bearing strength. The rotation of the segment joint was estimated in virtual design conditions based on the existing models and the proposed method. And the sectional force of the segment lining and joint were calculated along with the estimated rotation. As the rotation at the segment joint increases, the joint contact area decreases, so the designer have to verify the segment joint for bearing strength as well. This paper suggests a consistent method to determine the rotational stiffness and bearing strength of joints.