• 한국기계가공학회지
• /
• 제2권3호
• /
• pp.84-89
• /
• 2003

The joint method and characteristics of lubricant Impregnated MC nylon and metal are analyzed. Considering the productivity and economics, two materials are Joined with the process of turning, knurling, and induction heating. The Joint strength is determined by adhesion of the melted nylon, the size of knurl, and the interference from the difference of the diameters. The parameters affecting induction heating process are analyzed. The adhesion strength of the melted nylon is measured. Finally the joint strength is analyzed in the environments of low, room, and high temperature. The nylon/metal Joined material is expected to be widely used as the sliding machine elements with good friction and shear strength.

• 자원환경지질
• /
• 제33권4호
• /
• pp.309-320
• /
• 2000

Aperture is an important parameter for determining the hydraulic characteristics of fractured media. In this study the topography of artificial rock joint surface was measured using 3D laser profilometer to analyze the aperture distribution. The initial aperture distribution was determined when the contact area became one percent of total joint surface. The initial aperture distribution of granite joint, with the mean value of 0.78 mm and the standard deviation of 0.34 mm was much different from that of the marble joint, with the mean value of 0.57 mm and the standard deviation of 0.26 mm. Apertures of both granite and marble showed normal distributions. Aperture distribution with the contact area of 25% was also analyzed. Mean value was decreased to one third compared to the initial aperture, but the standard deviation was decreased slightly. To determine the spatial correlation of the aperture distribution variogram analysis was carried out on the initial aperture data. Most experimental variograms were fitted well with exponential model. It is expected that the measured aperture characteristics can be used for stochastic analysis of fluid flow through rock joints.

• Tribology and Lubricants
• /
• 제17권4호
• /
• pp.307-311
• /
• 2001

The friction and lubrication characteristics of joint cartilage were investigated using the metatarso-phalangeal joint cartilage of rabbit against rotating stainless steel disk. Friction tests were conducted by dry and bovine serum lubricated sliding at room and body temperatures. For the dry sliding tests, low friction coefficient of 0.1-0.15 was observed at the early period of test, and then the friction coefficient increased as a test continued. With increasing applied load the early period of low friction lengthens. For the lubricated sliding tests, the coefficient of friction decreased as the applied load increased. And also the coefficient of friction decreased continuously to 0.07 as the test duration increases. These results can be interpreted that the squeeze or weeping lubrication mechanism dominates the friction and lubrication characteristics in the joint cartilage of rabbit.

• 한국정밀공학회지
• /
• 제20권3호
• /
• pp.125-132
• /
• 2003

The joint method and characteristics of MC nylon and metal are analyzed. Considering the productivity and economics, two materials are joined with the process of turning, knurling, and induction heating. The joint strength is determined by adhesion of the melted nylon, the size of knurl, and the interference from the difference of the diameters. The adhesion strength of the melted nylon is measured. The effects of the knurl size and diameter difference are analyzed with the statistical methods. Finally the joint strength is analyzed in the environments of low, room, and high temperature. Based on this study, the nylon/metal material is expected to be widely used as the sliding machine elements with good lubrication and strength properties.

• 한국생산제조학회지
• /
• 제22권4호
• /
• pp.665-672
• /
• 2013

With the development of advanced processing technology, laser processing systems, which require high-quality precision processing, have attracted considerable attention. Although laser equipment is expensive, it enables quick processing and less deformation of materials. This technology is often applied to secondary batteries, which has thus farinvolved the use of argon tungsten inert gas (TIG) welding. However, the welding characteristics of argon TIG welding are not yet good, and a laser is used for welding to address this problem. In this study, lap-joint welding was conducted, and the desired welding characteristics were obtained when the laser power was 1800W and the laser beam travel speed was 1.8 m/min. Lap-joint welding was conducted on Ni-coated SS41. Two cases were compared. No pores were observed in the Ni-coated SS41 lap-joint welding part, and cracks appeared from the lap-joints. Moreover, the pole rod and tap were welded together in a T-joint form to improve the output of the secondary battery. T-joint laser welding showed better welding characteristics than TIG welding.

• 한국초전도ㆍ저온공학회논문지
• /
• 제16권1호
• /
• pp.32-35
• /
• 2014

Recently, many researches on the system of superconducting power supply and superconducting magnetic energy storage (SMES) using high temperature superconducting (HTS) tapes has been progressed. Those kinds of superconducting devices use the heater trigger switches that have a control delay problem at moments of heating up and cooling down. One way to reduce the time delay is using a different HTS tape at trigger part. For example, HTS tape having lower critical temperature can reduce time delay of heating up and heating down stage for heater trigger operation. This paper deals with resistances joint with different kinds of HTS tapes which have different properties to verify usefulness of the suggested method. Three kinds of commercial HTS tapes with different specifications are selected as samples and two kinds of solders are used for comparison. Joint is performed with temperature and pressure controllable joint machine and the joint characteristics are analyzed under the repeatable conditions.

• Steel and Composite Structures
• /
• 제20권3호
• /
• pp.469-486
• /
• 2016

Codes EN 1993 and EN 1994 require to take into account actual joint characteristics in the global analysis. In order to implement the semi-rigid connection effects in frame design, knowledge of joint rotation characteristics ($M-{\phi}$ relationship), or at least three basic joint properties, namely the moment resistance $M_R$, the rotational stiffness $S_j$ and rotation capacity, is required. To avoid expensive experimental tests many methods for predicting joint parameters were developed. The paper presents a comprehensive analytical model that has been developed for predicting the moment resistance $M_R$, initial stiffness $S_{j.ini}$ and rotation capacity of the minor axis, composite, semi-rigid joint. This model is based on so-called component method included in EN 1993 and EN 1994. Comparison with experimental test results shows that a quite good agreement was achieved. A computer program POWZ containing proposed procedure were created. Based on the numerical simulation made with the use of this program and applying regression analysis, simplified equations for main joint properties were also developed.

• 한국구조물진단유지관리공학회 논문집
• /
• 제23권4호
• /
• pp.8-14
• /
• 2019

한국 전통 목조 건축물의 경우 구조적 성능은 재료 특성, 접합부의 형태, 치목의 정밀도 등에 따라 다르게 나타난다. 기존 사례 연구에서도 보와 기둥 접합부 형태는 변형 및 간격의 정도에 큰 영향을 미친다는 것을 보고하고 있다. 이는 단층 건물뿐만 아니라 대규모 다층 건물의 경우에도 마찬가지로 나타나고 있다. 따라서 본 연구에서는 접합부 형태에 대해 분석하고 모형을 제작하고 구조적 성능을 테스트하는 과정을 거쳤다. 그 결과, 주먹장맞춤의 실험체에서 최대 하중을 나타냈다. 각각의 형태의 접합부에 의한 구조적 성능을 종합하면, 도래걷이 주먹장맞춤이 가장 높은 성능을 나타내었으며, 다음으로 도래걷이 장부맞춤의 순으로 나타났다. 건물의 구조적 성능은 관통하는 보의 치목 형태와 기둥 내부의 접합부 형테에 따라 다르게 나타남을 알 수 있었으며, 이는 다층 건물의 신축 또는 복원을 위해 고려되어야하며 이후 계속 연구되어야 할것으로 사료된다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.226-231
• /
• 2004

Press fitting method for joining of a hybrid tube and steel ring with small teeth for automotive aluminum/composite hybrid propeller shaft was devised to improve reliability and to reduce manufacturing cost, compared to other joining methods such as an adhesively bonded joint, bolted joint or welded joint. To obtain high strength of the press fit joint, an optimal design method for the teeth was devised with respect to number and shape of the steel teeth. Torsional static, fatigue tests and finite element analysis of the press fit joint were performed with respect to experimental variables. The developed optimal design method predicted well the static torque capability and failure mode of the press fit joint. Also, it provided design guide line of press fit joint for improving torsional static and fatigue characteristics.

• 지질공학
• /
• 제19권2호
• /
• pp.145-152
• /
• 2009

절리는 전파할 때 상대적인 이동이 절리 벽에 수직으로 일어난 평탄한 신장 열림 모드 단열이다. 층상 퇴적암에 발달하는 절리는 일반적으로 층리면에 수직이고 인접한 절리와 평행한 배향과 규칙적인 간격을 가지며 절리 조를 이룬다. 본문은 층상 퇴적암의 절리에 대한 최근 연구 결과들을 토대로 절리 전파의 역학적 규제, 층두께-절리간격의 관계, 절리 간격의 빈도 분포, 절리 포화, 절리 밀도, 교차 절리, 절리 발달 기구 등을 고찰 한다.