• Proceedings of the IEEK Conference
• /
• 2001.10a
• /
• pp.592-596
• /
• 2001

A TACUB jig was applied to separate waste plastics [polystyrene (PS), acrylonitrile butadiene styrene (ABS), and polyethylene terephthalate (PET)] used in copy machine. The effect of water pulsation including amplitude and frequency on the separation performance was investigated for the feeds containing two or three plastics. Good results are obtained under suitable conditions. Grades of 99.8% PS,99.3% ABS, and 98.6% PET are recovered as the products in the upper, middle and bottom layers respectively. Based on these results, a processing plant fer recycling of plastics from scrapped copy machines is now under construction.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.5
• /
• pp.2567-2572
• /
• 2014

In the present study, we aimed to obtain multi jig that PCB sheet with several PCB component can cut in a short time as to the Separation of PCB component. PCB supporter designed safely at the base frame and each model can be separable. it completed the neodium magnet for the fixing of the upper part laser transmission hole of the both. One of the development, the cutting working with one base frame which PCB component of various standard, fixing of module and bridge connected to PCB component could be possible. and it reduced the inconvenience which has to replace the base frame and PCB sheet fixed member. It compared to other press up about 70% of accuracy and a reduction in investment cost was about 400%.

• Mineral and Industry
• /
• v.28
• /
• pp.1-13
• /
• 2015

In this study, it was carried out separation process research and development to be able to produce high-grade tungsten concentrate form tungsten taken form Mongolia. In order to reduce treatment cost and increase separation efficiency the jig separation at first was applied for recovering the concentrate. Which reground would make the degree of liberation increase. Which was treated by shaking table to reject the gangue minerals from the first concentrate. Because the heavier product contains not only ferberite but also cassiterite, the product was treated by further dry magnetic separation to obtain the ferberite concentrate. Finally, the high-grade ferberite concentrate of 67.63% $WO_3$ could be obtained with recovery of 86.07% through the separation process developed in this study.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.38 no.8
• /
• pp.767-773
• /
• 2010

This paper describes development of a non-explosive separation device which can be equipped on small satellites. The spur geared micro DC motor, which has high reliability and advantage of price, is adopted as an actuator. The proposed separation device has resettability and it does not need extra jig to reload. In addition, the simple structure makes it easy to fabricate and assemble. To verify the performance of the proposed device, the response time tests, maximum preload tests and maximum shock level tests were performed. Also, through the vibration tests and thermal vacuum tests, feasibility of the proposed separation device was shown in launching and space environments. Therefore, we expect that the proposed separation device can replace the imported separation devices in near future.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.8
• /
• pp.4736-4741
• /
• 2014

This study examined PCB component cleaning on a PCB component surface, which has defects of precipitation type washing (existing rinse method), sealant and foreign material formed in the adhesive process that could not be removed easily. The spin jig was developed for PCB component cleaning, in which the PCB component settled down, to solve the conventional problem of the removal of foreign material with the centrifugal force by high speed rotation. The results are as follows. With decreasing fraction defect in PCB component washing, the development and substrate damage decreased by more than 80% according to the abstergent in the rotary type using the centrifugal force in the existing precipitation type. When the base plate showed a large difference with the time to include the process after washing the design using the existing method, easy attachment and separation of the PCB component could be possible. The washing time was enhanced 90% compared to the existing time. The reliability of the security and washing collaboration of the design and stability of the cleaning process could be secured so that there was no phenomenon of secession, the PCB component fixed for a cleansing rotation jig could maintain a fixed force by the centrifugal force. The stability and reliability of the washing process and the defective rate could be improved to less than 1%.

• Korean Journal of Materials Research
• /
• v.12 no.12
• /
• pp.935-940
• /
• 2002

Magnesium-3, 6wt% Nickel alloys were fabricated by Rotation-Cylinder Method(RCM) in ambient atmosphere. The alloys were divided into two different heat-treating conditions, as-cast and thixotropic treated. Thixotropic heat treatment enhances the separation of primary hydride former of Mg and the catalytic phase of $Mg_2$Ni. Hydrogenation properties of the each alloy were evaluated and compared by PCI(Pressure-Composition Isotherm) measurement. The maximum hydrogen capacity and the reversible capacity of as -cast Mg-6wt% Ni alloy were 5.2wt% and 3.8wt% at 623k, respectively.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.1798-1802
• /
• 2007

Adhesion strength of single layer ceramic capacitor sheet was measured using a peel testing system developed in this study. The peel test specimens with various dimensions were prepared from the ceramic sheet cast on the PET film. In peel test, the sheet specimen was adhered on the glass jig floating on the liquid media, which was designed to minimize the friction, and the specimen was then pulled up by micro-actuator. During the separation of the sheet from the PET film, peel force was measured. To normalize the testing condition, 3 different widths of the specimen were selected: 5, 10 and 20 mm. was used Furthermore, testing speed effect was investigated in this study. From the resullts using various testing conditions, the standard method for the peel strength testing may be suggested. Based on the testing condition, effect of peel angle on the strength was experimentally examined. It was found that the adhesive strength for the ceramic sheet is nearly identical, irrespective of the specimen width ranged from 5 to 20 mm, while the adhesive strength was increased with increasing testing speed. Furthermore, the strength was shown to be dependent on the peel angle.

• Journal of Korean Association for Spatial Structures
• /
• v.20 no.4
• /
• pp.123-130
• /
• 2020

Generally the non-bearing walls in apartment buildings in Korea are not considered as a lateral force resisting members for the design consideration. This engineering practice caused large crack damages and brittle fractures of the non-bearing walls when subjected to Pohang earthquakes in 2017 since those have not been designed for seismic loading. In this study, finite element analysis was conducted for slot type non-bearing wall connection system to reduce damages and concentrate damages to the designated damping device through separation from the structural wall members. Steel plate and dowel bar systems designed for the dissipation of seismic energies were modeled and analyzed to investigate the damage reductions. Finally, the test result and the analysis result were compared and verified.

• Mass Spectrometry Letters
• /
• v.8 no.4
• /
• pp.109-113
• /
• 2017

Single analytical procedure including extraction, liquid chromatography, and mass spectrometric analysis was evaluated for the simultaneous measurement of lysophospholipids (LPLs). LPLs, particularly, lysophosphatidic acids (LPA) and sphingosine 1-phosphate (S1P) are lipid messengers ubiquitously found in various biological matrix. The molecular species mediate important physiological roles in association with many diseases (e.g. cancer, inflammation, and neurodegenerative disease), which emphasize the significance of the simple and reliable analytical method for biomarker discovery and molecular mechanistic understanding. Thus, we developed analytical method mainly focusing on, but not limited by those lipid species S1P and LPA using reverse phase liquid chromatography-tandem mass spectrometry (RPLC-ESI-MS-MS). Extraction method was modified based on Folch method with optimally minimal level of ionization additive (ammonium formate 10 mM and formic acid). Reverse-phase liquid-chromatography was applied for chromatographical separation in combination with negative ionization mode electrospray-coupled Orbitrap mass spectrometry. The method validation was performed on human blood plasma in a non-targeted lipid profiling manner with full-scan MS mode and data-dependent MS/MS. The proposed method presented good inter-assay precision for primary targets, S1P and LPA. Subsequent analysis of other types of LPLs identified a broad range of lysophosphatidylcholines (LPCs) and lysophosphatidyl-ethanolamines (LPEs).

• Journal of Korea Foundry Society
• /
• v.23 no.3
• /
• pp.137-146
• /
• 2003

The main purpose of this study is to investigate the effects of process parameter on alpha-case formation of Ti and TiAl castings. The previous studies showed that the molten titanium is excessively reactive to the refractory oxide mold, resulting in alpha-caes of the titanium castings regardless of composition of titanium alloys. However, the behavior of the alpha-case formation of TiAl alloy is not consistent with conventional titanium alloy. In order to investigate the alpha-case formation of Ti and TiAl castings with process parameter, especially the associated factors of investment mold such as mold material, binder and mold preheating temperature. An attempt has been made to characterize the alpha-case of titanium casting by using optical microscope, EDS, XRD, EMPA and hardness profiles. The formation of the alpha-case on the surface of pure titanium during investment casting was rather by that of solid solution with metallic element from mold material. The required mold strength was obtained with $CaZrO_3$ because of the possibility of using water soluble binder. However, the separation phenomenon between facing and back-up mold materials should be considered. The interfacial reaction of TiAl alloy showed different behavior from that of pure titanium and $Al_2O_3$ was best mold materials. The effect of binder as well as mold material on the formation of alpha-case was significant.