• 한국정밀공학회지
• /
• 제29권3호
• /
• pp.295-301
• /
• 2012

The method for spraying of liquids through an electrical field has become a printing method since it can make very small droplet. For electro-hydrodynamic jet printing to become a reliable jetting tool, the jetting performance should be characterized with respect to various jetting conditions. To optimize jetting conditions, the jetting behavior should be measured. In this study, we present a visualization techniques to measure jetting behavior from electro-hydrodynamic (EHD) inkjet head. Unlike most previous method, we use the CCD camera to measure the jetting behavior. For this purpose, LED light is synchronized with jetting signal and sequential image was obtained by adjusting the delay time of the LED light. Finally, merits and demerits of using CCD camera were discussed to measure jetting image from EHD inkjet head.

• 한국정밀공학회지
• /
• 제29권4호
• /
• pp.449-454
• /
• 2012

The method for spraying of liquid through an electrical filed has become a printing method since it can make very small droplet. To increase the reliability using the electro-hydrodynamic (EHD) jet printing, the jetting status needs to be monitored. Vision measurement techniques using high speed camera has been used to visualize the jet images. However, it requires image processing of a lot of images after image acquisitions. So, it is difficult to understand jet behavior such as jetting frequency, jet repeatability etc. In this work, a low cost electrical current measurement method was developed to measure electrical current from EHD jet printing. To verify the jetting monitoring capability of developed circuit, images from high speed camera were processed for comparison purpose.

• 한국가시화정보학회지
• /
• 제13권2호
• /
• pp.33-37
• /
• 2015

매년 장마철에는 수막현상으로 인한 교통사고가 빈번하게 발생한다. 본 연구는 수막 형성 억제를 위해 타이어 앞부분에 설치되는 공기 분사 장치의 성능을 평가하는 것으로서, 공기 분사에 의한 수막 형성 억제를 모사할 수 있는 실험 장치를 제작하고, 수막 형성 억제 과정을 가시화하여 공기 분사 장치의 성능을 파악하고자 한다. 실험 변수로서 노즐의 형상 3가지와 수막에 대한 분사각 3가지에 대해 상세히 그 영향을 조사하였으며, 그 결과 분사각은 10도(지면에 대해서는 80도), 노즐 형상은 일자형일 때 수막 억제 효과가 가장 큰 것으로 파악되었다.

• 한국가시화정보학회지
• /
• 제9권2호
• /
• pp.48-53
• /
• 2011

The shape of nozzle cross-section plays an important role in stabilizing electrospray jet. The angle of contact line is governed based on the famous Young-Laplace equation. Compared to a round nozzle that has a constant curvature along the orifice, the square nozzle has four square corner edges and four straight edges that hold the meniscus in a different manner and is of interest in this study. By utilizing both square and round capillary nozzle, we examine the effect of nozzle shape in electrohydrodynamic jetting. The ejections were recorded with a high speed camera and analyzed to examine the jetting repeatability based on dynamic movement of meniscus. The result suggests that if the corner edges are not sharp, then its effect on repeatability is also limited.

• 한국가시화정보학회지
• /
• 제14권3호
• /
• pp.22-27
• /
• 2016

A sweeping jet actuator (SJA) is an instrument generating pulsing jets with no moving elements. Because of its simple design and high durability to shock and vibration, SJA has recently drawn increasing attention for the application to flow control such as aerodynamic control of a wing and thrust vectoring of a jet engine. However, experimental and numerical studies on SJA have been limited to internal flow structure of SJA. In this study, we investigated the flow structure and its variation in the outlet of SJA. We carried out the experiment to understand the flow structures using PIV (Particle Image Velocimetry). The flow structure varies with a degree of the outlet and volume flow rate. There is leaking process during half jetting cycle. The process of the main jet can occur because the jet moving time increased from one side to the other side.

• 한국가시화정보학회지
• /
• 제6권2호
• /
• pp.9-13
• /
• 2008

The reproducibility of water droplet formation which is indispensible in the investigation of a drop-on-demand piezoelectrically driven inkjet was verified by checking the size of droplet and distance from the nozzle tip of inkjet head to droplet. Based on the reproducibility of droplet formation, we visualized the formation of micro-scale droplets by acquiring consecutive images at the jetting frequency of 500 Hz for which air bubbles were not generated. Two different electric waveforms were used to drive the piezoelectric actuator. The visualization system consists of a high-speed camera that can capture images up to 250,000fps, a long-distance microscope and a halogen lamp as a light source.

• 한국가시화정보학회지
• /
• 제9권1호
• /
• pp.17-19
• /
• 2011

The bubble oscillations play an important role in ultrasonic cleaning processes. In the ultrasonic cleaning of semiconductor wafers, the cleaning process often damages micro/nano scale patterns while removing contaminant particles. However, the understanding of how patterns in semiconductor wafers are damaged during ultrasonic cleaning is far from complete yet. Here, we report the observations of the motion of bubbles that induce solid wall damage under 26 kHz continuous ultrasonic waves. We classified the motions into the four types, i.e. volume motion, shape motion, splitting or jetting motion and chaotic motion. Our experimental results show that bubble oscillations get unstable and nonlinear as the ultrasonic amplitude increases, which may exert a large stress on a solid surface raising the possibility of damaging microstructures.

• 한국가시화정보학회지
• /
• 제18권1호
• /
• pp.18-25
• /
• 2020

The droplet impact behavior is dominated by some parameters such as surface temperature, We number, surface and fluid property. Especially, Leidenfrost effect which prevents the contact between surface and droplet is very powerful phenomenon for determining droplet impact behavior. Due to this effect, the impact regime is divided into contact boiling regime and film boiling regime whether the droplet contact with the surface. Many studies have found that surface micro-structures which processed by surface processing are effective to overcome the Leidenfrost effect. In this study, droplet impact behaviors were compared using ethanol both on flat and laser-ablated Al surface. On the flat surface, impact regime was mainly divided by surface temperature. And there is key dominant parameter for each regime. On the laser-ablated surface, we could see changed impact regime and different impact behavior such as jetting and ejection of tiny droplets despite of same impact conditions.