• Journal of Astronomy and Space Sciences
• /
• 제20권3호
• /
• pp.163-174
• /
• 2003

The motion of 3C 120 Jet relative to the core is reasonably uniform and the VLBI scale jet connects outwards to a VLA ~ 100kpc scale. We measured the jet width variation from the center and found some indication of a power law which indicates the jet expands roughly with a constant opening angle and a constant flow velocity, $V_{f}{\cong}c$, from subparsec scales to ~ 100 kpc. With such a constant flow velocity and based on other physical parameters deduced from observed emission characteristics of the jet, we have established an equipartition jet model which might accommodate the basic parameters of the jet on subparsec scales, with which one can fit the radio intensities over all the scale of the jet even to ~100 kpc.

• 수산해양기술연구
• /
• 제27권4호
• /
• pp.255-265
• /
• 1991

분사류의 굴삭성능을 이용하여 해저의 모래속에서 서식하고 있는 패류를 어획할 목적으로 원형과 직사각형의 모형노즐을 제작하여 수조에서 분사노즐의 모래면에 대한 굴삭실험을 한 결과를 요약하면 다음과 같다. 1. 분사노즐에 의한 모래면의 최대 굴삭깊이와 폭은 분사속도와 노즐의 단면적의 크기에 비례하여 직선적으로 증가하며, 노즐의 분사거리에 대해서는 굴삭깊이는 직선적으로 감소하나, 굴삭폭은 직선적으로 증가한다. 2. 직사각형 노즐(폭 1mm)은 단면적이 같은 원형 노즐보다 굴삭성능이 다소 우수하였다. 3. 노즐별 분사각도와 분사속도, 분사거리에 따른 최대 굴삭깊이와 폭에 관한 실험식은 직선식으로 나타나며, 분사각도 45$^{\circ}$에서 직사각형노즐(폭 1mm)의 분사속도와 분사거리에 따른 실험식은 다음과 같다. D=0.0093V 하(0)-0.23H+5.7. W=0.0147V 하(0)+1.06H+10.2. 단, D: 최대 굴삭깊이(cm), V 하(0): 노즐의 분사속도(cm/sec) 926$\leq$V 하(0)$\leq$1504, W: 최대굴삭폭(cm), H: 노즐구멍에서 모래면까지의 거리(cm).

• 설비공학논문집
• /
• 제10권6호
• /
• pp.743-752
• /
• 1998

Experiments were performed to characterize single-phase heat transfer behavior of submerged liquid jet with multiple nozzle normally impinging on the smooth and extended surfaces. Arrays of 9 and 36 nozzles were used, with diameters of 0.5 to 2.0mm providing nozzle area ratio (AR) from 0.05 to 0.2. The square pin fin arrays were chosen as extended surfaces and the effects of geometrical parameters such as fin height, the ratio of fin width to channel width on heat transfer enhancement were examined. Single nozzle characteristics were also evaluated for comparison. The results clearly showed that heat transfer enhancement could be realized by using multiple nozzles at the constant volume flow rate. The average Nusselt number of multiple nozzle impingement on the smooth surface was correlated by the following equation : Nu/$Pr\frac{1}{3}=0.94 Re^{0.56}N^{-0.12}AR^{0.50}$The average heat transfer coefficients of multiple nozzle impingement on the extended surfaces decreased with increasing fin height and the ratio of fin width to channel width. The effectiveness of ex-tended surfaces ranged from 1.5 to 3.5 depending on the fin height, the ratio of fin width to channel width of pin fin arrays, nozzle number and nozzle area ratio.

• 설비공학논문집
• /
• 제3권5호
• /
• pp.395-403
• /
• 1991

The purpose of this investigation was to characterize nucleate boiling and burn-out heat flux for rectangular free jet with saturated water impinging perpendicularly and upward against a flat uniform heat flux surface. Heat flux measured for Reynolds number based on rectangular nozzle width and for aspect ratio. The result of nucleate boiling heat transfer was presented nondimensional experimental equation including Nusselt, Boiling, Subcooling, Reynolds and Weber number. The effect of aspect ratio of heated surface in the burn-out heat flux had not appeared distinctly. But for the same aspect ratio, burn-out heat flux increased linearly with increment of nozzle exit velocity.

• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.251-262
• /
• 1995

The goal of this study is to provide fundamental information on the design of a new diesel injector system. The cylindrical disk spray was made by an impinging disk insited below the exit of air-assist atomizor. The disintegration processes on a twin-fluid atomization by air-assist atomizor were investigated. Liquid jet was disintegrated at the condition that wavelength was equal and longer than the circumference of the liquid jet, .lambda. .geq. .pi.do. However, the wavelength and the diameter of the liquid jet were decreased according to the increasing of air velocity. The relative density distribution of droplets and pattern of spray by impinging disk were investigated with a C-CCD. Optimum design conditions for cylindrical disk spray were also achieved. The pattern of cylindrical spray can classified according to the size of the disk and the distance from the nozzle tip to the disk. When the space of the disk and the nozzle tip was narrow and the diameter of the disk was larger than that of the air orifice of the nozzle exit, the good distribution of spray could be achieved. When the air flowrate was constant, the spray width was decreased according to the increasing of the liquid flowrate. When the liquid flowrate was constant, the spray width was decreased according to the increasing of the air flowrate.

• 에너지공학
• /
• 제20권2호
• /
• pp.96-102
• /
• 2011

본 논문은 2차원 충돌제트 시스템에서 충돌판이 천이영역에 위치할때, 열전달성능이 감소하는 벽면분류영역의 열전달증진을 목적으로 난류촉진체인 정 4각 로드를 평판전열면 앞에 설치하고 로드와 로드사이의 피치(P)를 40 mm로 고정한 후 로드의 폭(W) 변화(4, 6, 8 mm) 및 로드와 전열면사이의 간극(C) 변화(1, 2, 4, 6 mm)에 따른 유동특성과 열전달특성에 대해 실험을 수행하고, 그 결과를 수치해석과 비교 검토하였다. 또한 로드가 설치되지 않은 경우와 정량적으로 비교하여 충돌제트 시스템에서 난류촉진체를 이용한 열전달증진에 관한 기초적 자료를 제공하고자 한다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2007년도 Techno-Fair 및 추계학술대회 논문집 전기물성,응용부문
• /
• pp.98-99
• /
• 2007

This study has successfully demonstrated the direct fabrication of polymer resistors using ink-jet printing technology as an alternative patterning to traditional photolithography. The polymer resistors were fabricated just by two layer processes using a ink-jet printer (DMP-2800, Fujifilm Dimatix). First, resistive materials was patterned by a ink-jet printing with the desired width and length. Next, resistor fabrication was completed by printing metal contact pads on the both sides of the polymer resistor. We used poly (3,4-ethylene dioxythiophene) poly(styrenesulfonate)(PEDOT:PSS) for the resistor material and a nano-sized silver colloid for the metal contact pads. We characterized the electrical properties of PEDOT:PSS by measuring sheet resistance and specific resistance on a glass substrate. From analysis of the measured resistances, the electrical resistances of the polymer resistors linearly increased as a function of printed width and length of resistors. The accuracy of the fabricated polymer resistor showed about $0.6{\sim}2.5%$ error for the same dimensions.

• 대한기계학회논문집B
• /
• 제21권4호
• /
• pp.486-493
• /
• 1997

Experimental investigations on the comparison of developments between transient jets and evolving jet diffusion flames have been made in initial injection period. To achieve this experiment, an ignition technique using a residual flame as the ignition source is devised. High speed Schlieren visualizations, and measurements including jet tip penetration velocities and jet widths of the primary vortex are employed to examine the developing processes for several flow conditions. It is seen that the developing behaviors in the presence of flame are greatly different from those in transient jet, and thus the flow characteristics in the transient part are also modified. The discernible differences are shown to consist of the delay of the rollup of the primary vortex, the faster spreading after the rollup due to exothermic expansion, and the survival of only a primary vortex. The growth of primary vortex in the transient jet is properly explained through an impulsively started laminar vortex prior to the interaction. It is also found that the jet tip penetration velocity varies with elapsed time and an increase in Res gives rise to a higher tip penetration velocity.

• 대한기계학회논문집B
• /
• 제26권4호
• /
• pp.531-538
• /
• 2002

Flow characteristics of a round jet with swirl number of 0.17 have been investigated using a hot -wire anemometry in the initial region within 10D(exit diameter). Swirl effects were observed by comparing centerline flow characteristics, similarities and turbulent budgets of a swirl jet and a free jet, respectively. To obtain similarity of the radial profiles mean velocity and higher moments were measured at the vertical pl anes, located at 2.5, 5.0, 7.5D, 10D, respectively. The centerline velocity characteristics were also measured. It is turned out that similarities of mean and Reynolds stress are established. The jet boundary has wider width than that of a free jet and the shear stress also becomes stronger. In addition the centerline decay becomes faster than that of the free jet, indicating that the swirl induces more entrainment in the initial region of the swirl Jet by transferring the axial mean kinetic energy into the swirl energy and, therefore, has wider boundary, compared with that of free jet.

• 대한기계학회논문집
• /
• 제16권6호
• /
• pp.1156-1162
• /
• 1992

본 연구에서는 종횡비가 다른 3가지의 날카로운 모서리를 가진 타원 슬롯노즐 (AR=1,2,4)을 풍동 수축부 끝에 장착하여 타원제트의 유동특성 및 축교차현상을 3-D LDV 시스템을 이용하여 조사하였다.