• 대한전자공학회논문지TC
• /
• 제46권8호
• /
• pp.1-9
• /
• 2009

본 논문은 무인기용 대전자전 송수신 장치 개발에 대한 연구로 재밍(jamming) 환경에 강건한 대역확산(DSSS) 송수신기 개발에 대해 기술한다. 대역확산 방식은 데이터의 전송률 보다는 재밍마진이 중요하기 때문에 송수신 장치의 개발 목표로 재밍마진이 15dB 이상이고, 확산코드를 변경 가능한 송수신기를 제작하는 것이다. 멀티패스 성분을 이용하기 위한 레이크 수신기와, FEC로 부호이득이 7.2dB인 터보 코드를 적용하였다. 본 논문에서는 대역확산 송수신 장치의 전체적인 구조와 설계방법, 기능시험 결과를 기술하고 결론을 맺는다.

• 전자공학회논문지S
• /
• 제36S권6호
• /
• pp.30-36
• /
• 1999

군 위성통신 체계는 재밍환경을 고려하여 설계되어야 한다. 재밍에 대한 대책으로 위성통신에 직접확산 부호분할 다중접속 방식(DS-CDMA)을 사용시 다중톤 재밍 환경에서 링크용량과 재밍마진을 분석하였다. 위성은 정지궤도에 위치한 위성으로 역확산/재확산방식 중계기를 사용하는 경우와 변복조 및 오류수정까지 하는 경우를 고려하여 각각 링크용량과 재밍마진을 계산하였다. 중계기에서 변복조 및 오류수정까지 하는 경우는 역확산/재확산만 하는 경우보다 용량이 2배이상 증가되는 것으로 나타났다.

• 한국군사과학기술학회지
• /
• 제7권2호
• /
• pp.48-56
• /
• 2004

This paper presents the GPS receiver's inherent interference effectiveness based on the receiver's internal processing gain. This research is to verify the weakness of the GPS satellite signals and evaluate the receiver's vulnerability in an interference situation. The experiment for the narrow band interference effectiveness for the L1 C/A code GPS receiver has been performed by using the Spirent GSS4765 jamming simulator. After analyzing the experimental result, it is compared with the calculated J/S value of the two different L1 C/A code GPS receivers. By the above result, the narrowband jamming effectiveness of the each jamming source and the jamming margin for the each receiver are to be analyzed in detail. Finally, we could utilize the result to analyze the jamming effectiveness on the GNSS receiver.

• 대한임베디드공학회논문지
• /
• 제7권2호
• /
• pp.71-78
• /
• 2012

Based on the Zigbee-based wireless sensor network, I suggest the way to reduce errors between the short distance, improving the accuracy of the presumed distance by revising the deviation of RSSI(Received Signal Strength Indication) values is to estimate the distance using only the RF signal power without the additional hardware. In general, the graph measured by RSSI values shows the proximity values which are ideally reduced in proportion to the distance under the free outdoor space in which LOS(Line-Of-Sight) is guaranteed. However, if the result of the received RSSI values are each substituted to the formula, it can produce a larger margin of error and less accurate measurement since it is based upon the premise that this free space is not affected by reflected waves or obstacles caused by the ground and electronic jamming engendered by the environment. Therefore, the purpose of this study is to reduce the margin of errors between the distances and to measure the proximity values with the ideal type of graph by suggesting the way to revise the received RSSI values in the light of these reflected waves or obstacles and the electronic jamming. In conclusion, this study proves that errors are reduced by comparing the proposed deviation correction method to the revised RSSI value.

• 한국정밀공학회지
• /
• 제2권3호
• /
• pp.28-40
• /
• 1985

In this study, to check up on the effect of the components of cutting resistance upon friction between drill and inside wall of hole in drilling, the experiment was performed with individual specimen of carbon steel, cast iron, aluminium alloy under various cutting conditions: depth of hole, cutting speed, feed rate, shape and material of specimen. On the basis of the experimental results, the following conclusions are drawn; 1. The components of cutting resis- tance were increased in proportion to the increase of depth of hole owing to frictional resistance of drill margin and chip-jamming. 2. As feed rates increase, torque and thrust were increased. When comparing to the increasing rate for these components respecitively, thrust is higher tendency than torque. 3. As drill diameter increase, torque and thrust were increased. When comparing to the increasing rate for these components respectively, torque is higher tendency than thrust. 4. In the case of torque, the frictional resistance between drill margin and inside wall of drilled hole accounts for about 20 percent of carbon steel, 14 of cast iron, 10 aluminium alloy in drilling. But the effect of thrust force could be negligible. 5. Comparison between the theoretical and experimental results showed a close agreement so far as depth of hole is about three times of drill diameter. But there was a wide difference between them beyond the rane of three times, because of characteristics of the drilling process.

• 항공우주시스템공학회지
• /
• 제11권3호
• /
• pp.16-21
• /
• 2017

본 논문에서는 drag-sail의 수납 효율을 높이기 위해 새로운 접기 방법인 blossom method를 제안하였다. 가항력 돛을 접을수록 두께가 늘어남에 따라 발생하는 문제점을 해결하기 위해 접히는 라인에 여유 공간(offset)을 주고, offset film 라인이 교차하는 지점에는 구멍을 뚫어 film의 일그러짐을 방지하였다. 또한, blossom method의 적용 가능성을 확인하기 위해 mylar film으로 제작하여 전개 실험을 수행하였다. Blossom method를 적용할 경우, 수납부피 대비 전개면적 비인 수납비는 1: 68.64로 기존의 가항력 돛 접기 방법인 z-fold method보다 약 1.88배 향상되었으며, 전개 실험 결과 구멍이나 jamming에 의한 손상이 없는 것을 확인하였다.