• Journal of The Korean Society of Agricultural Engineers
• /
• v.57 no.2
• /
• pp.1-13
• /
• 2015

The Coupled Model Intercomparison Project Phase 5 (CMIP5), coordinated by the World Climate Research Programme in support of the Intergovernmental Panel on Climate Change (IPCC) AR5, is the most recent, provides projections of future climate change using various global climate models under four major greenhouse gas emission scenarios. There is a wide selection of climate models available to provide projections of future climate change. These provide for a wide range of possible outcomes when trying to inform managers about possible climate changes. Hence, future agrometeorological indicators estimation will be much impacted by which global climate model and climate change scenarios are used. Decision makers are increasingly expected to use climate information, but the uncertainties associated with global climate models pose substantial hurdles for agricultural resources planning. Although it is the most reasonable that quantifying of the future uncertainty using climate change scenarios, preliminary analysis using reasonable factors for selecting a subset for decision making are needed. In order to narrow the projections to a handful of models that could be used in a climate change impact study, we could provide effective information for selecting climate model and scenarios for climate change impact assessment using maximum/minimum temperature, precipitation, reference evapotranspiration, and moisture index of nine Representative Concentration Pathways (RCP) scenarios.

• Journal of Biosystems Engineering
• /
• v.11 no.1
• /
• pp.52-63
• /
• 1986

This study was performed to find out drying characteristics and develop drying model for the design of an efficient dryer or drying system of red peper. The basic model which describes drying phenomenon of red pepper was firstly established, and drying tests were conducted at 14-different drying conditions. In this test, the effects of drying air temperature and relative humidity on the rate of drying were undertaken. Finally, a new drying model based on these experimental results was developed to describe the drying characteristics of red pepper. The results from this study may be summarized as follows. 1. Drying constant of the basic model established from Lewis' experimental model and diffusion equation was theoretically deduced as a function of moisture content and inner-temperature of red pepper. 2. From the results of drying tests, drying air temperature was found to have the greatest effect on the rate of drying. However, the effect of temperature was small for the condition of high relative humidity, and for low temperature, the effect of relative humidity was found to be large even though the range of relative humidity was low. 3. Modified Henderson equation was found to be better than Chung equation as the EMC model for the estimation of the equilibrium moisture content of red Pepper. 4. Constant-rate drying period did not exist in the red pepper drying test. And falling-rate drying period was divided into three distinct phases. Drying rate was dependent on the moisture content, the inner-temperature of red pepper and the change of physical property due to drying. 5. Drying constant increased with decrease of free moisture content, but it decreased at the end of the drying period. Also, drying constant was dependent on the drying air temperature and relative humidity. 6. The new drying model developed in this study was found to be most suitable in describing the drying characteristics of red pepper. Therefore, it may be concluded that drying time could be accurately estimated by the new drying model.

• Asian-Australasian Journal of Animal Sciences
• /
• v.28 no.8
• /
• pp.1061-1065
• /
• 2015

Data collected from 690 purebred Duroc pigs from 2009 to 2012 were used to estimate the heritability, and genetic and phenotypic correlations between production and meat quality traits. Variance components were obtained through the restricted maximum likelihood procedure using Wombat and SAS version 9.0. Animals were raised under the same management in five different breeding farms. The average daily gain, loin muscle area (LMA), backfat thickness (BF), and lean percent (LP) were measured as production traits. Meat quality traits included pH, cooking loss, lightness ($L^*$), redness ($a^*$), yellowness ($b^*$), marbling score (MS), moisture content (MC), water holding capacity (WHC), and shear force. The results showed that the heritability estimates for meat quality traits varied largely from 0.19 to 0.79. Production traits were moderate to highly heritable from 0.41 to 0.73. Genotypically, the BF was positively correlated (p<0.05) with MC (0.786), WHC (0.904), and pH (0.328) but negatively correlated with shear force (-0.533). The results of genetic correlations indicated that selection for less BF could decrease pH, moisture content, and WHC and increase the shear force of meat. Additionally, a significant positive correlation was recorded between average daily gain and WHC, which indicates pork from faster-growing animals has higher WHC. Furthermore, selection for larger LMA and LP could increase MS and lightness color of meat. The meat quality and production traits could be improved simultaneously if desired. Hence, to avoid further deterioration of pork characteristics, appropriate selection of traits should be considered.

• International Journal of Automotive Technology
• /
• v.5 no.3
• /
• pp.215-219
• /
• 2004

A vehicle structure needs to be more precisely analyzed because of complexities and varieties. Structural fatigue which is generated by fluctuations of stresses during the service life of a mechanical system is the primary concern in the structural design for safety. A fatigue life is difficult to obtain in structural components during the service life of mechanical systems since the fluctuating stress contributes to fatigue. This study introduces new procedures to measure the lethargy coefficient and to predict the fatigue life of a mechanical structure by using molecular dynamic simulation. A lethargy coefficient is the total defect-estimating coefficient, which was obtained by using the results of a simple tensile test in this study. With this lethargy coefficient, fatigue life was estimated. The proposed method will be useful in predicting the fatigue life of a structurally-modified vehicle design. The effectiveness of the proposed method using lethargy coefficient measurement to predict the fatigue life of a structure was examined by applying this method to predict the fatigue life of SS41 steel, used extensively as material of vehicle structures. Two types of specimen such as pre-cracked plate and simple plate is discussed. equation of fatigue life using the lethargy coefficient and failure time, both obtained from a simple tensile test, will be useful in engineering. This measurement and prediction technology will be extended for use in analysis of any geometric shapes of modified automotive structures.

• Geomechanics and Engineering
• /
• v.4 no.4
• /
• pp.281-294
• /
• 2012

Filtration using granular media such as quarried sand, anthracite and granular activated carbon is a well-known technique used in both water and wastewater treatment. A relatively new pre-filtration method called pebble matrix filtration (PMF) technology has been proved effective in treating high turbidity water during heavy rain periods that occur in many parts of the world. Sand and pebbles are the principal filter media used in PMF laboratory and pilot field trials conducted in the UK, Papua New Guinea and Serbia. However during first full-scale trials at a water treatment plant in Sri Lanka in 2008, problems were encountered in sourcing the required uniform size and shape of pebbles due to cost, scarcity and Government regulations on pebble dredging. As an alternative to pebbles, hand-made clay pebbles (balls) were fired in a kiln and their performance evaluated for the sustainability of the PMF system. These clay balls within a filter bed are subjected to stresses due to self-weight and overburden, therefore, it is important that clay balls should be able to withstand these stresses in water saturated conditions. In this paper, experimentally determined physical properties including compression failure load (Uniaxial Compressive Strength) and tensile strength at failure (theoretical) of hand-made clay balls are described. Hand-made clay balls fired between the kiln temperatures of $875^{\circ}C$ to $960^{\circ}C$ gave failure loads of between 3.0 kN and 7.1 kN. In another test when clay balls were fired to $1250^{\circ}C$ the failure load was 35.0 kN compared to natural Scottish cobbles with an average failure load of 29.5 kN. The uniaxial compressive strength of clay balls obtained by experiment has been presented in terms of the tensile yield stress of clay balls. Based on the effective stress principle in soil mechanics, a method for the estimation of maximum theoretical load on clay balls used as filter media is proposed and compared with experimental failure loads.

• Asian-Australasian Journal of Animal Sciences
• /
• v.18 no.9
• /
• pp.1221-1225
• /
• 2005

The peroxisome proliferator-activated receptors (PPARs) are members of a superfamily of nuclear hormone receptors. Lots of studies in rodents and humans have shown that PPARs were involved in lipid metabolism and adipocyte differentiation. The main objective of this work was to detect the single nucleotide polymorphisms (SNPs) in whole coding regions of peroxisome proliferator-activated receptor alpha (PPAR-$\alpha$) and gamma (PPAR-$\gamma$) genes with approach of single strand conformation polymorphism (SSCP) in the chicken population of Arber Acres broiler, Hyline layer and three Chinese native breeds (Shiqiza, Beijing You, Bai'r). Two SNPs of C1029T and C297T were found in chicken PPAR-$\alpha$ and PPAR-$\gamma$ genes respectively and each SNP found three genotypes in the experimental populations. The results showed that the distribution frequency of 3 genotypes in Arber Acres broiler, Hyline layer and Chinese native breeds had significant differences on the PPAR-$\alpha$ and PPAR-$\gamma$ gene respectively (p<0.01). Furthermore, in the PPAR-$\alpha$ gene, the results of least square estimation for genotypes and body composition traits showed the BB genotype birds had higher abdominal fat weight (AFW) and percentage of abdominal fat (AFP) than AA genotype birds (p<0.05). From these we conjecture the PPAR-$\alpha$ and PPAR-$\gamma$ genes were suffered intensive selection during the long term commercial breeding and the PPAR-$\alpha$ gene may be a major gene or linked to the major genes that impact chicken fat metabolism and the SNPs could be used in molecular assistant selection (MAS) as a genetic marker for the chicken fatness traits.

• Journal of Microbiology and Biotechnology
• /
• v.20 no.7
• /
• pp.1134-1139
• /
• 2010

This study explored the chronic effects of different doses of the triazole fungicide tebuconazole on the growth, and metabolic and enzymatic functions of the filamentous paddy field cyanobacterium, Westiellopsis prolifica Janet. The growth of the cyanobacterium was determined by an estimation of the change in pigment contents. Chlorophyll-a, carotenoids, and accessory pigments such as phycocyanin, allophycocyanin, and phycoerythrin were shown to decline over a 16-day period by a factor of 92%, 93%, 83%, 95%, and 100%, respectively, with increasing doses of the fungicide. Metabolic and enzymatic activities were also adversely affected. Over the 16 days, a gradual rise in total phenol content was recorded when Westiellopsis prolifica Janet was treated with 60 ppm of the fungicide, despite the reduction in carbohydrates, proteins, and amino acids by 96%, 92%, and 90%, respectively. Moreover, the enzymes nitrate reductase (NR), glutamine synthetase (GS), and succinate dehydrogenase (SDH) also registered reductions of 93%, 90%, and 98%, respectively. This study indicates that tebuconazole, although an important fungicide used extensively in rice fields, exhibits an inhibitory effect on the growth and metabolic activities of Westiellopsis prolifica Janet and hence possibly on other varieties as well.

• Proceedings of the KIEE Conference
• /
• 2005.11b
• /
• pp.3-5
• /
• 2005

21세기의 무한 경쟁 환경에서 기업의 생존은 고객 만족에 의해 좌우된다고 해도 과언이 아니다. 한편, 고객 만족을 달성하기 위해서는 고객의 욕구가 어떻게 변화하고 있는가를 충실히 파악하여야 한다. 헌재의 고객은 제품의 기본 기능과 가격 똥의 요소뿐만 아니라, 제품의 품질, 특히 신뢰성에 매우 민감한 반응을 보이고 있으며, 각 기업은 이러한 추세를 반영하여 제품의 보증기간을 경쟁적으로 연장하고 있다. 신뢰성이란 제품이 얼마나 오랫동안 고장 없이 의도한 기능을 발휘할 수 있는가를 나타낸다. 즉, 신뢰성이란 시간적 품질을 의미하며 제품이 충분한 신뢰성을 가지고 있지 못할 경우, 과도한 클레임으로 인한 보증비용의 증가와 같은 단기적인 손해뿐만 아니라, 고객 불만족, 고객 이탈, 기업 경쟁력 상실 통으로 야기되는 장기적인 손실에 이르기까지 매우 큰 피해를 감수해야 한다. 따라서 제품의 신뢰성은 기업의 생존과 경쟁력 우위를 확보하기 위한 중요한 전략적 요소로 다루어 져야 한다. 신뢰성 활동은 크게 신뢰성 평가와 신뢰성 설계 두 가지로 나눌 수 있다. 전자는 현재 개발 또는 양산 중인 제품의 신뢰성 수준이 어느 정토인가를 파악하자 하는 활동이며, 후자는 제품에 신뢰성을 높이기 위한 일련의 활동을 포함한다. 한편, 신뢰성 평가는 모든 신뢰성 업무에서 앞서 선행적으로 이루어 져야 하는 기초적 활동이며, 본 과제에서는 자사의 전자식 전력량계(LSEW12)와 디지털 보호계전기(GIPAM2200)를 대상으로 신뢰성 평가에 관한 연구를 수행하였다.

• The Bulletin of The Korean Astronomical Society
• /
• v.42 no.2
• /
• pp.66.2-66.2
• /
• 2017

The Korea Astronomy and Space Science Institute plans to develop a coronagraph in collaboration with National Aeronautics and Space Administrative (NASA) and install it on the International Space Station (ISS). The coronagraph is an externally occulted one stage coronagraph with a field of view from 2.5 to 15 solar radii. The observation wavelength is approximately 400 nm where strong Fraunhofer absorption lines from the photosphere are scattered by coronal electrons. Photometric filter observation around this band enables the estimation of 2D electron temperature and electron velocity distribution in the corona. Together with the high time cadence (< 12 min) of corona images to determine the geometric and kinematic parameters of coronal mass ejections, the coronagraph will yield the spatial distribution of electron density by measuring the polarized brightness. For the purpose of technical demonstration, we intend to observe the total solar eclipse in 2017 August for the filter system and to perform a stratospheric balloon experiment in 2019 for the engineering model of the coronagraph. The coronagraph is planned to be installed on the ISS in 2021 for addressing a number of questions (e.g. coronal heating and solar wind acceleration) that are both fundamental and practically important in the physics of the solar corona and of the heliosphere.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.30 no.8 s.251
• /
• pp.931-940
• /
• 2006

Defect assessment of a weld zone is important in fitness-for-service evaluation of plant components. Typically a J and $C^*$ estimation method for a defective homogeneous component is extended to a mismatched component, by incorporating the effect due to the strength mismatch between the weld metal and the base material. The key element is a mismatch limit load. For instance, the R6/R5 procedure employs an equivalent material concept, defined by a mismatch limit load. A premise is that if a proper mismatch limit load solution is available, the same concept can be used for any defect location (either a weld centre defect or a heat affected zone (HAZ) defect) and for any material combination (either two-material or multi-material combinations; either similar or dissimilar joints). However, validation is still limited, and thus a more systematic investigation is needed to generalise the suggestion to any geometry, any defect location and any material combination. This paper describes the effect of structural geometry on the $C^*$ integral for defective similar welds, based on systematic elastic-creep 2-D and 3-D finite element (FE) analyses, to attempt to elucidate the questions given above. It is found that the existing 'equivalent material' concept is valid only for limited cases, although it provides conservative estimates of $C^*$ for most of cases. A modification to the existing equivalent material concept is suggested to improve accuracy.