• 폴리머
• /
• 제29권6호
• /
• pp.588-592
• /
• 2005

자외선을 차단할 목적으로, 단일 모재를 사용함으로써 기존 방법이 갖고 있는 차단제의 적층에 따른 두께 증가와 접착제의 반응 온도에 따른 변형 등의 단점을 개선하고자 하였다. 화장품 용기 및 옥외용으로 사용 가능한 고분자 필름(폴리카보네이트) 표면에 이온 조사를 통하여 고분자 표면을 개질하였다. 표면 개질된 필름의 280$\∼$400 nm 사이 자외선 차단 특성, 표면의 화학 및 형태 변화 특성, 자외선에 대한 저항성을 W분광기, FTIR(ATR)과AFM, UV 촉진 내광성 시험기를 이용하여 측정하였다. 분석 결과, 개질된 고분자 필름은 자외선 전 영역을 차단할 수 있었고 이온의 주입량에 따라 차단율을 자유롭게 변화시킬 수 있었다. 이는 이온들의 주입으로 인한 고분자의 표면 화학 변화에 기인한다. 개질된 고분자 표면은 nm수준으로, 별도의 차단제가 필요없는 하나의 모재로, 자외선 차단을 위해 활용 할 수 있으리라 판단된다. 또한 자외선 조사에 따른 고분자의 색 변화 및 자외선 투과 특성 변화가 없음을 확인하여 일상 생활환경에서 지속적인 자외선 차단 방법으로 사용 가능하리라 기대할 수 있었다.

• 한국태양에너지학회 논문집
• /
• 제27권3호
• /
• pp.149-154
• /
• 2007

It is essential to know the heat transfer characteristics at the absorber plate of Flat-plate solar collector for optimum design. For flat-plate solar collector, it is difficult to experimentally study the effect for the Reynolds number of riser considering low mass flow rate being applied into the collector with one riser tube. So, this study were performed to show the heat transfer characteristics of flat-plate solar collector with single absorber plate and riser for various Reynolds number at riser using commercial code FLUENT 6.0. The base collector size is chosen with $0.4m^2$ as 0.2m by 2m with single riser in this study, Reynolds number at riser is from 200 to 1200 including about 530 at typical flat-plate collector with 10 risers considering the mass flow rate of 0.02kg/s per collector area for the certificate test Through the simulation, the results were presented as the temperature distribution at the absorber plate for various flow rate and solar irradiance conditions, then showed the effective length scale of the absorber plate The real solar irradiation condition is assumed as the constant heat flux condition of $500w/m^2$ considering the annual average solar irradiance in Korea.

• Journal of Periodontal and Implant Science
• /
• 제45권2호
• /
• pp.38-45
• /
• 2015

Purpose: The purpose of this study was to evaluate the effect of photodynamic therapy (PDT) using erythrosine and a green light emitting diode (LED) light source on biofilms of Aggregatibacter actinomycetemcomitans attached to resorbable blasted media (RBM) and sandblasted, large-grit, acid-etched (SLA) titanium surfaces in vitro. Methods: RBM and SLA disks were subdivided into four groups, including one control group and three test groups (referred to as E0, E30, E60), in order to evaluate the effect of PDT on each surface. The E0 group was put into $500{\mu}L$ of $20{\mu}M$ erythrosine for 60 seconds without irradiation, the E30 group was put into erythrosine for 60 seconds and was then irradiated with a LED for 30 seconds, and the E60 group was put into erythrosine for 60 seconds and then irradiated with a LED for 60 seconds. After PDT, sonication was performed in order to detach the bacteria, the plates were incubated under anaerobic conditions on brucella blood agar plates for 72 hours at $37^{\circ}C$, and the number of colony-forming units (CFUs) was determined. Results: Significant differences were found between the control group and the E30 and E60 groups (P<0.05). A significantly lower quantity of CFU/mL was found in the E30 and E60 groups on both titanium disk surfaces. In confocal scanning laser microscopy images, increased bacterial death was observed when disks were irradiated for a longer period of time. Conclusions: These findings suggest that PDT using erythrosine and a green LED is effective in reducing the viability of A. actinomycetemcomitans attached to surface-modified titanium in vitro.

• Journal of Radiation Protection and Research
• /
• 제34권1호
• /
• pp.9-14
• /
• 2009

High density polyethylene (HDPE) is degraded due to a radiation-induced oxidation when it is used as a neutron moderator in a neutron counter for a nuclear material accounting of spent fuels. The HDPE exposed to the gamma-ray emitted from the fission products in a spent nuclear fuel results in a radiation-induced degradation which changes its original molecular structure to others. So a neutron moderating power variation of HDPE, irradiated by a gamma radiation, was investigated in this work. Five HDPE moderator structures were exposed to the gamma radiation emitted from a $^{60}Co$ source to a level of $10^5-10^9$ rad to compare their post-irradiation properties. As a result of the neutron measurement test with 5 irradiated HDPE structures and a neutron measuring system, it was confirmed that the neutron moderating power for the $10^5$ rad irradiated HDPE moderator revealed the largest decrease when the un-irradiated pure one was used as a reference. It implies that a neutron moderating power variation of HDPE is not directly proportional to the integrated gamma dose rate. To clarify the cause of these changes, some techniques such as a FTIR, an element analysis and a densitometry were employed. As a result of these analyses, it was confirmed that the molecular structure of the gamma irradiated HDPEs had partially changed to others, and the contents of hydrogen and oxygen had varied during the process of a radiation-induced degradation. The mechanism of these changes cannot be explained in detail at present, and thus need further study.

• 한국재료학회지
• /
• 제26권12호
• /
• pp.714-720
• /
• 2016

We performed this study to understand the effect of a single-crystalline anode on the mechanical properties of as-deposited films during electrochemical deposition. We used a (111) single- crystalline Cu plate as an anode, and Si substrates with Cr/Au conductive seed layers were prepared for the cathode. Electrodeposition was performed with a standard 3-electrode system in copper sulfate electrolyte. Interestingly, the grain boundaries of the as-deposited Cu thin films using single-crystalline Cu anode were not distinct; this is in contrast to the easily recognizable grain boundaries of the Cu thin films that were formed using a poly-crystalline Cu anode. Tensile testing was performed to obtain the mechanical properties of the Cu thin films. Ultimate tensile strength and elongation to failure of the Cu thin films fabricated using the (111) single-crystalline Cu anode were found to have increased by approximately 52 % and 37 %, respectively, compared with those values of the Cu thin films fabricated using apoly-crystalline Cu anode. We applied ultrasonic irradiation during electrodeposition to disturb the uniform stream; we then observed no single-crystalline anode effect. Consequently, it is presumed that the single-crystalline Cu anode can induce a directional/uniform stream of ions in the electrolyte that can create films with smeared grain boundaries, which boundaries strongly affect the mechanical properties of the electrodeposited Cu films.

• 한국항공우주학회지
• /
• 제42권8호
• /
• pp.629-639
• /
• 2014

강성이 우수하고, 경량으로 제작이 가능한 격자강화 복합재 구조체를 다기능 구조체의 기층구조로 적용함으로써, 전기전자회로를 용이하게 내장할 수 있으며 방사차폐 특성을 갖춘 다기능 구조체에 대한 설계 및 제작을 수행하였다. 피치계열 탄소섬유 복합재료의 적용을 통해 열전달특성을 향상시키고, 전자회로의 하우징 구조물이 없어도 우주방사환경에 충분한 내구성을 갖도록 경량 국부 강화 방사차폐 방법을 제안하고, 양성자 조사시험을 통하여 선택적 방사차폐의 효과를 검증하였다.

• Toxicological Research
• /
• 제27권3호
• /
• pp.153-160
• /
• 2011

To evaluate the whitening effect of black tea water extract (BT), BT was topically applied to artificially hyperpigmented spots on the back skins of brown guinea-pigs (weight: 450~500 g) induced by 1,500 mJ/$cm^2$ of ultraviolet B (UVB) irradiation. The test compounds of 30 ${\mu}l$ were applied twice a day, six days a week, for four weeks. The artificially hyperpigmented spots were divided into 5 groups: control (UVB + saline, C), vehicle control [UVB + propylene glycol: ethanol: water (5 : 3 : 2), VC], positive control (UVB + 2% hydroquinone, PC), experimental 1 (UVB + 1% BT), experimental 2 (UVB + 2% BT). After 4-week application, the spots were removed by biopsy punch under anesthetic condition and used as specimens for the histological examination. The total polyphenol and flavonoid contents of BT were 104 and 91 mg/g, respectively. The electron-donating ability of BT revealed a dose-dependent response, showing the excellent capacities of 86% at 800 ${\mu}g$/ml. The artificially hyperpigmented spots treated with the PC and BT were obviously lightened compared to the C and VC groups. At the fourth week, the melanin indices for the PC and BT groups were significantly lower (p < 0.001) than those of the C and VC groups. In histological examination, PC and BT groups were significantly reduced in the melanin pigmentation, the proliferation of melanocytes and the synthesis of melanosomes compared to the C and VC groups. It is found that BT inhibits the proliferation of melanocytes and synthesis of melanosomes in vivo using brown guinea pigs, thereby showing a definite skin whitening effect.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2002년도 Proceedings of the International Welding/Joining Conference-Korea
• /
• pp.187-192
• /
• 2002

Applicability of laser micro welding process to the fabrication of medical devices was investigated. Austenitic stainless steel wire (SUS304) was spot melted and crosswise welded, which is one of the most possible welding process for the fabrication of medical devices, by using a Nd-YAG laser. Effects of welding parameters on the microstructure, tensile strength and corrosion resistance were discussed. In the spot melting, melted metal width decreased with decreasing the input energy and pulse duration. Controlling the laser wave to reduce laser noise which occurred in the early stage of laser irradiation made reasonable welding condition wider in the welding condition of small pulse duration such as 2ms. The microstructure of the melted metal was a cellular dendrite structure and the cell size of the weld metal was about 0.5~3.5 ${\mu}{\textrm}{m}$. Tensile strength increased with the decrease of the melted metal width and reached to a maximum about 660MPa, which is comparable with that for the tempered base metal. Even by immersion test at 318K for 3600ks in quasi biological environment (0.9% NaCl), microstructure of the melted metal and tensile strength hardly changed from those for as melted material. In the crosswise welding, joints morphologies were classified into 3 types by the melting state of lower wire. Fracture load increased with input energy and melted area of lower wire, and reached to a maximum about 80N. However, when input energy was further increased and lower wire was fully melted, fracture load decreased due to the burn out of weld metal.

• 한국해양공학회지
• /
• 제19권4호
• /
• pp.28-34
• /
• 2005

In the study application of volcanic scoria concrete to artificial reefs is investigated. Volcanic scoria is a natural volcanic product that shows light weight, mil/i-porous, and far-infrared irradiation characteristics. The properties of volcanic scoria concrete using Jeju scoria aggregate are evaluated by conducting a comprehensive series of tests on strength and void ratio. It is concluded that the volcanic scoria concrete has the sufficient strength of 4MPa-13MPa and adequate void ratio of $12\%-35\%$ to be accepted as artificial reef concrete. The field experiments are performed through observation by scuba diver's at the Seogwipo coast. Porous specimen and plane concrete specimen are prepared for comparison purposes. Seasonal changes of soft coral on the two series of test specimens were have been observed from Apr. 9, 2004 to Mar. 18, 2005. The soft coral is well grown on the porous specimen however there are no significant changes on the conventional plain concrete specimen. Thus it is concluded that the volcanic scoria concrete is highly suitable as artificial reef concrete.

• The Journal of Korean Physical Therapy
• /
• 제21권1호
• /
• pp.1-7
• /
• 2009

Purpose: The aim of this study was to determine the effect of proprioceptive neuromuscular facilitation (PNF) leg patterns on muscle activation of paretic and nonparetic arm in post-stroke hemiparetic subjects. Methods: Eighteen hemiparetic patients participated in this study. Each subject was asked to perform four PNF leg patterns against maximal manual resistance on nonparetic leg. EMG data were collected from biceps and triceps on the paretic and nonparetic side. The measured EMG data was digitized and processed to root mean square (RMS) and expressed as percentage maximal voluntary isometric contraction (％MVIC). The data were analyzed using paired t-test and one-way analysis of variance (ANOVA) with repeated measures to determine the statistical significance. Results: The results of this study were summarized as follows: Firstly, during four PNF patterns application, all of the ％MVIC values of biceps and triceps in paretic and nonparetic arms increased significantly compared with resting condition (p<0.05). Secondly, there was a significant difference in ％MVIC of paretic biceps between PNF leg pattern 1 and 4 (p<0.05). Conclusion: In conclusion, regardless of the kinematic components of PNF leg patterns, all of the muscle activation of biceps and triceps in paretic and nonparetic arm was significantly increased. The finding of this study indicates that irradiation effect caused by PNF leg patterns is beneficial for increased muscle activation of both paretic and nonparetic arms in post-stroke patients.