• Korean Journal of Heritage: History & Science
• /
• v.46 no.3
• /
• pp.134-149
• /
• 2013

The Sudang-ri Site in Geumsan is considered the historic site where Baekje dominated the inland traffic route to Gaya through Geumsan and Jinan in the 5th Century. This study identified the production techniques of iron by conducting an analysis of metallographical microstructure of the artifacts such as an iron sword and an iron sickle that were excavated in Sudang-ri Site, Geumsan, one of the regions ruled by Baekje, and tried to figure out the characteristics and the technical systems of Baekje's ironmaking around the 5th Century by comparing them with other iron artifacts produced around the same time. The analysis showed that various production techniques were applied to the artifacts excavated in Sudang-ri Site, Geumsan. Depending on the production techniques, they can be divided largely into three methods: the simple shape-forging method, the steel manufacture method after forging, and the steel manufacture & heat-treatment method after forging. The iron sickle from the stone chamber tomb No. 1, which was produced only through forging, is mostly composed of soft ferrite at both edges of the blade and at the rear making the use of the weapon impractical. From this fact, it is presumed that they were produced as burial objects or ceremonial accessories for the person buried. The iron axe from the outer stone coffin tomb No. 1 and the iron swords and sickle from the outer stone coffin tomb No. 12, which were produced through the steel manufacture method after forging such as carburizing, did not go through the heat treatment such as quenching, but applied different production processes to each part. Therefore, it is deemed that they were produced as daily tools for cultivation rather than burial objects or ceremonial accessories. The production techniques following the forging process - carburizing and heat treatment - can be found on the iron swords from the outer stone coffin tomb No. 5 and the outer stone coffin tomb No. 12. The sturdy structure of the blade part and the durable structure of the rear processed with heat are deemed to have been produced as weaponry and used by the person buried. Based on the analysis of the iron artifacts excavated from Sudang-ri Site in Geumsan, the characteristics of iron production techniques were investigated by comparing them with the artifacts from Yongwon-ri Site in Cheonan, Bongseon-ri Site in Seocheon, and Bujang-ri Site in Seosan that were made around the same time as the cluster of Baekje tombs examined by the metallographical microstructure analysis of this study. For the iron artifacts analyzed here, the changes in the techniques were investigated using the iron swords common in all of the tombs. In the case of the iron swords, it was identified the heat treatment technique called tempering was applied from the 4th Century.

• Journal of Conservation Science
• /
• v.35 no.4
• /
• pp.317-329
• /
• 2019

Slag was collected from the iron-producing furnace site in Saengsoegol, Baegun mountain, where iron was manufactured by a righteous army against Japan in the Gwangyang region; then, the iron-manufacturing technique of the early modern period was investigated through scientific analysis. In the microstructure analysis results of the selected samples, iron bloom was mainly observed together with magnetite and fayalite. In the component analysis results of the compounds, it was confirmed that the furnace was built by using gangue of alkali feldspar or plagioclase series, and the ironmaking work was performed at a high temperature of at least 1050℃, because mullite was identified together with cristobalite and hercynite. Based on the chemical composition, it was speculated that low-grade iron ores were used as raw materials, and it seemed that the yield was low, because the total Fe content of the smelting slag samples was 37.72-49.93%. It was difficult to confirm whether a slag former was used, and it seemed that materials easily obtained nearby were used when the furnace was built, without considering the corrosion resistance. It appeared that the ironmaking work was performed at the Gwangyang Saengsoegol iron-producing furnace based on the direct ironmaking method in an environment that could escape the vigilance of the Japanese Empire to produce weapons that would be used for the resistance against Japan. It seemed that there was neither an advanced ironware production system nor a mass production system, and small-scale works were performed in short periods of time.

• Journal of Conservation Science
• /
• v.38 no.1
• /
• pp.33-44
• /
• 2022

The study, iron-making process was examined through the scientific analysis of six by-products that were obtained during iron making at the Songdu-ri site in Jincheon. The total Fe content of the slags excavated from the Songdu-ri site was 36.29-54.61 wt%, whereas the deoxidation agent was 26.48-49.08 wt%. The compound analysis result indicated that fayalite and wüstite are the main compounds in slag. Furthermore, the microstructure analysis result confirmed the presence of fayalite and wüstite in the slag. It can be inferred from the flat shape in a bright matrix structure of the hammer scales that forging was performed in the latter stage. The Raman micro-spectroscopy results confirmed that the surface was hematite (Fe₂O₄), middle layer was magnetite (Fe₃O₄), and inner layer was wüstite (FeO). The presence of smelting and smithing slags, spheroid hammer scales, and flake hammer scales suggests that at the Songdu-ri site, iron-making process is carried out by division of labor into producing iron bloom through direct smelting, refining and forge welding, and ingot production.

• Journal of Conservation Science
• /
• v.34 no.4
• /
• pp.273-281
• /
• 2018

$Ji{\check{u}}di{\grave{a}}n$ iron production site in China is a relic smelting site, which in the past produced pig iron. In this study, scientific analysis of the smelting furnace and collected slag was conducted to reveal some aspects of the ancient Chinese smelting technique. A 3D model of the smelting furnace showed a narrow lower part and an upper section which increased in diameter upwards. Although the smelting furnace relic does not include the upper part and its complete shape cannot be predicted, the remaining part suggests that the furnace had a larger diameter in the central part compared to the upper and lower parts. Most of the collected slag was completely vitrified. Long prismatic fayalite was observed in the matrix of some samples. The iron particles contained phosphorus, which could not be discharged during smelting work. In addition, as the $CaO/SiO_2$ ratio was 0.42 or lower in the results of the content analysis, no CaO slag former had been added. However, the ratio of $CaO/SiO_2$ to $Al_2O_3/SiO_2$ did not have a constant trend. This needs to be investigated in a further study.

• Journal of Conservation Science
• /
• v.29 no.2
• /
• pp.139-147
• /
• 2013

This study focused on iron making related information through analyzing slags and furnace wall collected from iron production site of Suryong-ri Wonmorongi, Chungju. Total Fe content of slags were from 36.98% to 44.47% and this range was general recovery rate of iron in ancient. Compounds of calcium included slags was supposed to add intentionally during smelting process as deoxidation agent in order that these helped to separate iron from impurities. Furnace wall didn't make of high alumina clay because of low $Al_2O_3$. Microstructure and main components of slags show that No. 1 to 3 slags with fayalite and wustite were products of iron ore smelting. However, No.4 slag is more likely to smelt by iron sand because of ulvospinel with $TiO_2$ in No. 4 slag. Therefore, iron ore were not only used but iron sand in smelting and furnace wall made of general clay with low $Al_2O_3$ content in this area.

• Journal of Conservation Science
• /
• v.36 no.2
• /
• pp.143-151
• /
• 2020

In the present article, we have analyzed five slags excavated from the Unified Silla period iron smelting site, i.e., location 4-2 of the Inje Bupyeong-ri site, to investigate the iron smelting process. The total Fe content of the slag excavated from the Inje Bupyeong-ri site ranged between 3.65 and 23.78 wt%, lower than that of typical slag, and deoxidation agent of the slag ranged between 65.92 and 88.96 wt%, higher than that of typical slag. These results suggest that the recovery rate of iron was significantly high. Furthermore, cristobalite was detected in most of the samples, and the furnace temperature, estimated by substituting the analyzed data into the FAS and FCS state diagrams, was confirmed as 1,600℃ or more. These results suggest that the operation at the Inje Bupyeong-ri site was performed at a temperature capable of producing cast iron by completely melting the carbon-containing iron. Observation of the microstructure showed that the iron fragments excavated at the Inje Bupyeong-ri site were identified as white cast iron. Steadite from the ternary iron-carbon-phosphorus system was observed in the white cast iron structure. These results show that indirect smelting was performed when the iron smelting by-products were produced. Based on the analysis results, it was confirmed that the Inje Bupyeong-ri site was the indirect smelting site in the Unified Silla period.

• 보존과학연구
• /
• s.27
• /
• pp.165-180
• /
• 2006

The research was conducted to understand type of iron used by those who lived at dwelling site of Yangsoo-ri in between the first century B.C. and the first century A.D. to make steel products and their technique such as steel making process and heat treatment, based on micro structure information obtained through microscopic metallographic structure analysis with SEM-EDS of six steel productsexhumed at the site. Key findings are summarized as below. In the sense that Si-Ca-Al style and less than 0.5% of Ti were found in the non-metallic inclusion, the material used for forged iron ware was magnetite resolved in that. It is, however, unclear whether magnetite was resolved at high temperature or at low temperature. Microscopic structure analysis revealed that forged steel products were made through repeated hot working, the technique of molding by hitting after heating in the process of resolving and molding iron. As a result, the iron used here for the products was not the iron ore which was produced through resolution from discarded cast iron axe, ingot iron. It is probable that to make those steel products, disposed-of cast iron was reused after being molded by decarburizing. Although a few of relics were analyzed for the research, they were of critical importance in defining the process of ironware production from the first century B.C. and the first century A.D. at the Yangsoo-ri region. Judging from the iron from A-19 dwellingsite, it is possible to conclude that the iron was manufactured from cast iron decarburized and yet more research has to be done into relics yetto be exhumed in order to ascertain the finding. All of these findings are believed to play a critical role in further studies to define the steel-manufacturing technique used on the central Korean peninsular in the ancient times.

• Journal of architectural history
• /
• v.25 no.5
• /
• pp.27-40
• /
• 2016

The purpose of this study was to comprehend the procurement system of iron materials and the production process of ironwork in royal tombs constructions in the later Joseon period. For this purpose, sixteen Sanneung-uigwes were analyzed. The following conclusions have been reached through the study. First, it was procuring five types of iron materials in constructions of royal tombs. Sincheol had been supplied up to the mid-18th century. On the other hand, the amount of jeongcheol was increased rapidly. Because of the procurement system of initial tools was changed from bokjeong(a kind of tribute) to self-production in the Noyaso. Second, the government stockpiles were utilized as much as possible than bokjeong to manage the limited construction period and sudden construction start. Third, before moving the site of tombs, the melting furnace was installed in the Gungisi(armament factory). The amount of the melting furnace was increased from 5 to 8 since producing the initial tools in the Noyaso. Fourth, six kinds of master artisans were worked in the field of producing ironwork. Metal worker was assigned to one person per melting furnace. Fifth, the quality of final iron materials was controlled by use. Since the 19th century, it had been produced enhanced ironwork.

• Journal of Conservation Science
• /
• v.31 no.4
• /
• pp.411-427
• /
• 2015

The purpose of the present study is to examine the objects excavated from the archaeological site of the Nogye Village in terms of their relationships with the iron production facilities such as 1ho smithing hearth and 2ho smelting furnace. 32 samples including slags, iron ores, and wall were analyzed to identify the mineralogical and chemical characterization. In addition, in the case of the 1ho smithing hearth slag, differing points of the cross-section were analyzed to examine its formation in depth. The analysis results suggest that the slags from the each site adjacent to the 1ho smithing hearth and 2ho furnace are related to smithing and smelting process respectively. Furthermore, it is possible to draw some conclusions that the aspects of the increased contents of nonferrous elements such as CaO in the slags in comparison with those of the iron ores are due to various factors such as charcoal ash and analytical reasons rather than an addition of CaO as flux.

• Bulletin of the Korean Chemical Society
• /
• v.32 no.1
• /
• pp.95-99
• /
• 2011

$CaTi_{1-x}Fe_xO_3(0{\leq}x{\leq}0.4)$ solid solution photocatalysts were synthesized by iron doping during the conventional solid state reaction at $1100^{\circ}C$ for 5 h and characterized by ultraviolet-visible (UV-vis) absorption spectroscopy, X-ray diffraction, morphological analysis. We found that $CaTi_{1-x}Fe_xO_3$ samples not only absorb UV but also the visible light photons. This is because the Fe substitution at Ti-site in $CaTi_{1-x}Fe_xO_3$ lattice induces the band transition from Fe3d to the Fe3d + Ti3d hybrid orbital. The photocatalytic activity of Fe doped $CaTiO_3$ samples for hydrogen production under UV light irradiation decreased with the increase in the Fe concentration. There exists an optimized concentration of iron in $CaTiO_3$, which yields a maximum photocatalytic activity under visible light ($\lambda\geq420nm$) photons.