• Proceedings of the KWS Conference
• /
• 2009.11a
• /
• pp.38-38
• /
• 2009

36 percent nickel-iron alloy possesses a useful combination of low thermal expansion, moderately high strength and good toughness at temperatures down to that of liquid helium, $-269^{\circ}C$. These propeties coupled with good weldability and desirable physical properties make this alloy attractive for many cryogenic applications such as the cargo containment system in Liquefied Natural Gas carriers and pipes for low temperature. Generally, welding method of the 36% nickel-iron is applied with the manual and autogeneous GTAW. Lately white spots have been observed on the some autogeneous GTA welds of them. But the white spot formation have not been studied yet. This paper covers the analysis results of the white spots formation as changing welding variables.

• Corrosion Science and Technology
• /
• v.10 no.5
• /
• pp.175-179
• /
• 2011

The transportation and deposition of iron corrosion products are important elements that affect both the steam generator (SG) integrity and secondary system in pressurized water reactor (PWR) nuclear power plants. Most of iron corrosion products are generated on carbon steel materials due to flow accelerated corrosion (FAC). The several parameters like water chemistry, temperature, hydrodynamic, and steel composition affect FAC. It is well established that the at-temperature pH of the deaerated water system has a first order effect on the FAC rate of carbon steels through nuclear industry researches. In order to reduce transportation and deposition of iron corrosion products, increasing pH(t) tests were applied on secondary system of A, B units. Increasing pH(t) successfully reduced flow accelerated corrosion. The effect of increasing pH(t) to inhibit FAC was identified through the experiment and pH(t) evaluation in this paper.

• Resources Recycling
• /
• v.17 no.3
• /
• pp.29-34
• /
• 2008

Solvent extraction behaviors of iron(III) from chloride solution at high ionic strength condition between Alamine336 and TBP were compared by using MaCabe-Thiele diagram. Extraction isotherms of iron by the two extractants were obtained by calculating the equilibrium concentrations of iron in both phases from the initial extraction conditions. In calculating the equilibrium concentration of iron, chemical equilibria in the aqueous phase and mass balance together with the solvent extraction reaction were considered. MaCabe-Thiele diagram of iron by 1M Alamine336 indicated that two extraction stages could lead to complete extraction of 0.5M iron from 3M HCl solution at an A/O ratio of 6/5. The extraction power of 1M Alamine336 was found to be the same as 2-3M TBP. MaCabe-Thiele diagram together with the physical properties of the two extractants indicated that Alamine336 is superior to TBP in extracting ferric iron from chloride solution.

• 한국연소학회:학술대회논문집
• /
• 2004.11a
• /
• pp.33-40
• /
• 2004

Combustion of coke/anthracite in an iron ore sintering bed is characterized quantitatively by introducing newly defined parameters related to propagation and thickness of combustion zone and maximum temperature. The parameters are obtained by sintering pot experiment and I-D, unsteady numerical model which treats solid material as multiple solid phases. Experiments and calculations are performed for various major operating parameters: air inlet velocity, different type of fuels which have different reactivity and diameter of the solid fuel. Effects of the operating parameters on the productivity and quality of the sintering process are investigated and evaluated quantitatively and the results show that optimized air supply rate and diameter of anthracite for replacement of coke can be obtained. This approach can be applied to other kinds of combustors for characterization of the combustion in the solid fuel beds.

• Proceedings of the KIEE Conference
• /
• 2001.07b
• /
• pp.708-710
• /
• 2001

In this paper, back commutation phenomena for iron chute chamber in AC low testing. For this experimental we used high speed camera and carried out with same prospective currents up to 10kA RMS. Hybrid arc quenching chambers which are composed with iron plate and insulating materials tested for reducing back commutation phenomena in interrupting process. It is shows that hybrid chambers which are various narrow slot path width reduces back commutation. As a result, a new type arc quenching chamber is to force the arc rapidly into a narrow insulating slot with iron plate. By this means the arc is lengthened and squeezed between insulating walls. Using this model, the behavior of the arc squeezed in the hybrid chamber and characteristics of arc voltage are also investigated.

• Tribology and Lubricants
• /
• v.20 no.6
• /
• pp.299-305
• /
• 2004

The wear properties of clutch facing materials with two different copper amounts were evaluated against the fly-wheel materials used in clutch system, such as gray cast iron and spheroidal graphite cast iron. Sliding wear tests were carried out for four different combinations with these clutch facing materials and flywheel materials at different speeds and applied loads. Results showed that the clutch facing material contained a higher copper amount had the better wear resistance. And using the gray cast iron as the counter material, clutch facing material resulted in the much lower wear rate, regardless of the copper amount. It is obvious that the wear properties of clutch facing material are influenced from the thermal conductivities of the clutch facing material and the counter material.

• Proceedings of the KIPE Conference
• /
• 2006.06a
• /
• pp.158-162
• /
• 2006

A lot of pieces of iron plate are used to build a ship. The states of cutting surface of iron are however bended or ununiformly cuttled by cutting machine. These may cause bad Quality of painting, and shorter lifetime of iron by rust. In this paper, a new approach of grinding force control method which teaching of robot is not required is proposed to avoid long preparation time of robot and to improve the productivity. The way used in this paper is just like a blind man works through the road with stick only.

• Resources Recycling
• /
• v.17 no.5
• /
• pp.37-43
• /
• 2008

Stripping experiments of iron from the loaded Alamine336 by sulfurous, chloric and sulfuric acid solutions have been performed by varying the concentration of acid and stripping conditions. The stripping percentage of iron decreased with the increase of HCl and $H_{2}SO_4$ concentration, while that increased with the increase of $H_{2}SO_3$ concentration up to 3 M. Stripping temperature had adverse effect on the stripping percentage of iron in the stripping by $H_{2}SO_3$ solution, while the stripping percentage of iron by HCl solution increased with the increase of temperature. Stripping isotherm of iron by 0.1 M HCl and 0.1 M $H_{2}SO_4$ solution indicated that three and four stripping stages could result in a solution containing 0.05 M iron at an O/A ratio of 1/10 from the loaded Alamine336 phase where iron concentration was 0.5 M.

• Clinical and Experimental Pediatrics
• /
• v.53 no.5
• /
• pp.661-665
• /
• 2010

Anemia caused by vitamin B12 deficiency resulting from inadequate dietary intake is rare in children in the modern era because of improvements in nutritional status. However, such anemia can be caused by decreased ingestion or impaired absorption and/or utilization of vitamin B12. We report the case of an 18-year-old man with short stature, prepubertal sexual maturation, exertional dyspnea, and severe anemia with a hemoglobin level of 3.3 g/dL. He had a history of small bowel resection from 50 cm below the Treitz ligament to 5 cm above the ileocecal valve necessitated by midgut volvulus in the neonatal period. Laboratory tests showed deficiencies of both vitamin B12 and iron. A bone marrow examination revealed dyserythropoiesis and low levels of hemosiderin particles, and a cytogenetic study disclosed a normal karyotype. After treatment with parenteral vitamin B12 and elemental iron, both anemia and growth showed gradual improvement. This is a rare case that presented with short stature and delayed puberty caused by nutritional deficiency anemia in Korea.

• Journal of Korea Foundry Society
• /
• v.14 no.1
• /
• pp.45-51
• /
• 1994

The possibility of using bulk talc as molding material was reviewed and tested with the measurement of thermal properties and computer simulations. The measured thermal conductivity and heat diffusivity($k{\rho}c$) of talc were $2.4W/m^{\circ}C$ and $6.6{\times}10^6J^2/m^4^{\circ}C^2s$, respectively. Thermal properties of talc could be ranked between those of sand mold and iron mold. Talc transforms into cristobalite and enstatite at $910^{\circ}C$, During the transformation volume and structure change, cracks appear on the surface and distortion occurs. Therefore talc can be used for molding material below $910^{\circ}C$ if carefully treated. Computer simulation was carried out to test whether talc insert could promote directional solidification in sand mold and iron mold. In sand mold, it was possible to achieve directional solidification of thin plate casting with the length to thickness ratio of 15, if both iron insert and talc insert were used. In iron mold, it was possible to achieve directional solidification only with talc insert.