• 한국대기환경학회지
• /
• 제17권6호
• /
• pp.475-485
• /
• 2001

The presence of airborne particles in the earth atmosphere expert important controls on the global climate because of their effects on the radiative balance. However, there are major uncertainties associated with the direct and indirect radiative effects of aerosols. In addition, their physicochemical properties cannot only the decline of air quality but also damage human health. Airborne particles were collected by two different commercial air samples, high volume sampler(for TSP) and low volume sampler(for P $M_{10}$ ) at the campus of Kunsan National University during February to September, 2000. In most cases, TSP and P $M_{10}$ were sampled once a week for the duration of 24 hours from 9:00 a.m. In addition samples were collected more intenisve, when the yellow dust was expected. Each sample was analyzed for pH and major ions concentration (C $l^{[-10]}$ , S $O_4$$^{2-}$, N $O_3$$^{[-10]}$ , N $a^{+}$, N $H_4$$^{+}$, $K^{+}$, $Mg^{2+}$, $Ca^{2+}$) by ion chromatography and atomic absorption spectrophotometry. Acidity (pH) of TSP and P $M_{10}$ ranged from 5.09 to 8.51 and from 6.22 to 7.54, respectively. The concentrations of airborne particles were found to satisfy both the short and long-term air quality standards during the sampling period. If the ratio of ionic concentrations originating from None sea salt(Nss) to sea salt(ss) in aerosol samples was concerned, it was found that the ionic concentrations from marine environment contributed dominantly in total mass concentration in the airborne particles. When seasonal trends were examined, the TSP concentrations in spring were higher than those of other seasons. It may result form frequent occurrences of yellow dust and during the spring season. The concentration ratio of P $M_{10}$ to TSP ranged from 0.78 to 1 during the sampling period. pH in the airborne particle was highest during spring, but the other seasons maintained almost same level. These results suggest that alkaline species in yellow dust can directly neutralize aerosol acidity. During spring season, yellow dust could be a positive factor that can defer the acidification of surface soil and water by neutralizing acidic aerosols in the atmosphere.osphere.

• 센서학회지
• /
• 제7권1호
• /
• pp.31-38
• /
• 1998

ISFET을 측정할 때 다채널 센서를 이용하면 신뢰도를 향상시킬 수 있고 노이즈를 제거할 수 있다. 향후 하나의 소자를 이용하여 여러 가지 이온을 측정할 수 있는 센서를 제조하기 위해서도 다채널 센서는 반드시 필요한 과정이다. 그러나 다채널 센서를 개발시 각 센서에 개별적으로 바이어스를 인가한다면 센서의 개수만큼 바이어스 회로가 필요하다. 본 논문에서는 영전위회로에 스위칭방식을 도입하여 4개의 pH-ISFET을 바이어스 하는 방식을 제안하였다. 제안된 회로는 4개의 센서에 대해 단지 하나의 바이어스 회로가 필요하므로 개별적인 바이어스 인가방식에 비해 전력을 적게 소모하며 적은 면적에 구현할 수 있다. 제안된 회로는 이산소자를 이용하여 성능을 검증하였다. 또한 최근 센서시스템이 휴대화 되어지는 경향에 따라 검증된 바이어스 회로를 CMOS를 이용하여 집적화 하였다. 설계된 바이어스 회로의 마스크 면적은 $660{\mu}m{\times}500{\mu}m$이다. ISFET은 반도체 집적회로 공정에 의해 제조되므로 향후 CMOS를 이용한 신호처리 회로와 함께 하나의 칩에 집적화 하여 다기능, 다채널, 그리고 지능형의 스마트센서 시스템으로 개발되어져야 바람직할 것이다.

• 대한조선학회논문집
• /
• 제28권1호
• /
• pp.60-68
• /
• 1991

비압축성 유체유동에 대한 Navier-Stokes 방정식과 충돌 접촉면 조건으로 특징지어지는 강체-유체 충돌문제를 Lagrangian 유한요소법에 의해 해석하였으며, 계산의 편의상, 속도장을 점성및 중력항과 압력항으로 나누어 수행하는 소위 fractional step method를 도입하였다. 유체영역은 4절점의 4각형 요소로 분할하였으며, 충분히 작은 시간간격의 도입을 전제로 하여 explicit time marching법으로 수치해석하였다. 매 시간 step의 초기에 우선 운동량-충격량 법칙으로 강체의 수면충돌후 속도를 구했으며, 그 속도로 표현되는 충돌 접촉면의 경계조건과 완전한 형태의 자유표면조건 그리고 운동방정식 및 연속 방정식을 모두 만족하는 속도장을 구하였다. 본 논문에서 제시하는 수치해석법에 의하면, 유체충격문제에 있어 매우 중요하다고 알려져 있는 tip splash를 포함하는 자유표면의 형상을 쉽게 추적해 갈 수 있다. Lagrangian 유한요소법의 적용의 타당성을 확인하기 위하여 대칭형 2차원 쐐기 모양의 강체가 수면충돌하는 경우를 예로하여 시간의 경과에 따른 충격수압의 분포 및 충격외력 등을 추정한 결과, 본 방법의 적용의 유효성과 아울러 몇가지 유용한 결론을 유도할 수 있었다.

• Bulletin of the Korean Chemical Society
• /
• 제23권8호
• /
• pp.1121-1126
• /
• 2002

Two anhydrous crystal structures of fully dehydrated Cd2+ - and Cs+ -exchanged zeolite X, Cd32Cs28Si100Al92O384 (Cd32Cs28-X: a = 24.828(11) $\AA)$ and fully dehydrated Cd,sup>2+ - and Rb+ -exchanged zeolite X, Cd28Rb36Si100Al92O384 (Cd28Rb36-X: a = 24.794(2) $\AA$), have been determined by single-crystal X-ray diffraction techniques in the cubic space group Fd3 at $21(1)^{\circ}C.$ The structures were refined to the final error indices, R1 = 0.058 and R2 = 0.065 with 637 reflections for Cd32Cs28-X and R1 = 0.086 and R2 = 0.113 with 521 reflections for Cd28Rb36-X for which I > $3\sigma(I)$. In the structure of Cd,sub>32Cs28-X, 16 Cd2+ ions fill the octahedral sites I at the centers of the double six rings (Cd-O = $2.358(8)\AA$ and O-Cd-O = $90.8(3)^{\circ}$ ). The remaining 16 Cd2+ ions occupy site II (Cd-O = $2.194(8)\AA$ and O-Cd-O = $119.7(4)^{\circ})$ and six Cs+ ions occupy site II opposite to the single six-rings in the supercage; each is $2.322\AA$ from the plane of three oxygens (Cs-O = 3.193(13) and O-Cs-O = $73.0(2)^{\circ}).$ Aboutten Cs+ ions are found at site II', $1.974\AA$ into the sodalite cavity from their three oxygen plane (Cs-O = $2.947(8)\AA$ and O-Cs-O = $80.2(3)^{\circ}).$ The remaining 12 Cs+ ions are distributed over site III' (Cs-O = 3.143(9) and O-Cs-O= $59.1(2)^{\circ})$. In the structure of Cd28Rb36-X, 16 Cd2+ ions fill the octahedral sites I at the center of the double-sixrings (Cd-O = 2.349(15) and O-Cd-O = $91.3(5)^{\circ}$ ). Another 12 Cd2+ ions occupy two different II sites (Cd-O = $2.171(18)/2.269(17)\AA$ and O-Cd-O = $119.7(7)/113.2(7)^{\circ}).$ Fifteen Rb+ ions occupy site II (Rb-O = $2.707(17)\AA$ and O-Rb-O = $87.8(5)^{\circ}).$ The remaining 21 Rb+ ions are distributed over site III' (Rb-O = $3.001(16)\AA$ and O-Rb-O = $60.7(4)^{\circ})$. It appears that the smaller and more highly charged Cd2+ ions prefer sites I and Ⅱ in that order, and the larger Rb+ and Cs+ ions, which are less able to balance the anionic charge of the zeolite framework, occupy sites II and II' with the remainder going to the least suitable site in the structure, site III'.The maximum Cs+ and Rb+ ion exchanges were 30% and 39%, respectively. Because these cations are too largeto enter the small cavities and their charge distributions may be unfavorable, cation-sieve effects might appear.

• 생태와환경
• /
• 제41권1호
• /
• pp.73-80
• /
• 2008

본 연구에서는 고탁도의 사육조건에서 탁수가 어류의 조직과 생리에 미치는 영향을 조사하기 위하여 참갈겨니의 아가미와 신장을 사용하였다. 탁도가 높고 사육기간이 길어질수록 아가미에서는 이차 새변의 간격이 불규칙해지고, 곤봉화, 부종, 상피세포의 박리가 나타났으며 새변 사이에는 이물질의 부착이 두드러지게 관찰되었다. 신장조직에서도 탁도의 증가에 따라 사구체가 수축되고 있으며 보우만 주머니의 공간이 넓게 관찰되었다. 고탁도의 탁수가 아가미와 신장 조직 내 항산화효소의 활성에 미치는 영향을 조사해 보면 SOD활성은 아가미와 신장 조직에서 고탁수로 감에 따라 활성이 증가하였으나 CAT와 GPX의 활성은 주로 신장에서 높은 활성을 나타내었다. 즉 고탁수의 스트레스에 의해 생성되는 유해한 라디칼은 주로 신장 조직의 항산화효소에 의해 제거하는 것으로 사료된다. 탁도 변화에 따라 어체에 축적되는 미량 중금속 농도의 경우 탁도가 매우 높은 1,000 NTU에서는 대조실험군 어류에 비해 중금속의 함량이 급격히 증가되는 경향을 보이고 있다. 이러한 결과로 보아 장기간 고탁도가 유지된다면 아가미와 신장 조직은 비정상적인 형태로 변형되고 중금속은 체내에 급격히 축적됨으로 치명적인 유해 작용을 나타낼 수 있을 것으로 생각된다.

• 자원환경지질
• /
• 제51권6호
• /
• pp.509-520
• /
• 2018

알칼리도(alkalinity)는 물의 화학적 특성을 결정하고, 각종 오염물질의 거동에 직간접적인 영향을 주는 중요한 기본 변수이다. 그러나, 적지 않은 실험실과 연구자들이 적절하지 못한 분석법으로 지하수의 알칼리도를 분석하고 있으며, 이것이 불량한 이온균형오차를 야기하는 큰 이유가 되고 있다. 본 연구는 현재까지 보고된 알칼리도분석법들을 조사하고 그 장단점을 분석함으로써, 지하수 알칼리도 분석을 수행하는 실험실이나 분석자들에 도움을 주기 위한 목적으로 수행되었다. 본 연구를 통하여 pH적정곡선의 변곡점으로 알칼리도 적정 종점(end point)를 찾는 방법이 가장 정확도가 높음을 알 수 있었다. 그 중에서도 Gran적정법이 종점까지 적정한 용액의 부피를 정확히 산출하는데 가장 적절한 것으로 조사되었다. 반면, 현재에도 여전히 많이 이용하고 있는 pH지시약을 이용하여 적정하는 방법이나 미리 정해진 pH를 종점으로 하여 적정하는 방법은 묽거나 알칼리도가 낮은 지하수의 분석에는 문제가 있는 것으로 판단된다.

• Journal of Ginseng Research
• /
• 제43권2호
• /
• pp.272-281
• /
• 2019

Background: Diabetic sensorineural damage is a complication of the sensory neural system, resulting from long-term hyperglycemia. Red ginseng (RG) has shown efficacy for treatment of various diseases, including diabetes mellitus; however, there is little research about its benefit for treating sensorineural damage. Therefore, we aim to evaluate RG efficacy in alloxan-induced diabetic neuromast (AIDN) zebrafish. Methods: In this study, we developed and validated an AIDN zebrafish model. To assess RG effectiveness, we observed morphological changes in live neuromast zebrafish. Also, zebrafish has been observed to have an ultrastructure of hair-cell cilia under scanning electron microscopy. Thus, we recorded these physiological traits to assess hair cell function. Finally, we confirmed that RG promoted neuromast recovery via nerve growth factor signaling pathway markers. Results: First, we established an AIDN zebrafish model. Using this model, we showed via live neuromast imaging that RG fostered recovery of sensorineural damage. Damaged hair cell cilia were recovered in AIDN zebrafish. Furthermore, RG rescued damaged hair cell function through cell membrane ion balance. Conclusion: Our data suggest that RG potentially facilitates recovery in AIDN zebrafish, and its mechanism seems to be promotion of the nerve growth factor pathway through increased expression of topomyosin receptor kinase A, transient receptor potential channel vanilloid subfamily type 1, and mitogen-activated protein kinase phosphorylation.

• 한국항해학회지
• /
• 제13권1호
• /
• pp.21-53
• /
• 1989

In the past twenty years, there has been a rapid increase in the volume of traffic in Korea due to the Korean great growth of the Korean economy. Since transformation provides an infrastructure vital to economic growth, it becomes more and more an integral part of the Korea economy. The importance of coastal shipping stands out in particular, not only because of the expansion limit on the road network, but also because of saturation in the capacity of rail transportation. In spite of this increase and its importance, coastal shipping is falling behind partly because it is givenless emphasis than ocean-going shipping and other inland transportation systems and partly because of overcompetition due to excessive ship tonnage. Therefore, estimating and planning optimum ship tonnage is the first take to develop Korean coastal shipping. This paper aims to estimate the optimum coastal ship tonnage by computer simulation and finally to draw up plans for the ship tonnage balance according to supply and demand. The estimation of the optimum ship tonnage is peformed by the method of Origin -Destimation and time series analysis. The result are as follows : (1) The optimum ship tonnage in 1987 was 358, 680 DWT, which is 54% of the current ship tonnage (481 ships, 662, 664DWT) that is equal to the optimum ship tonnage in 1998. this overcapacity result is in excessive competition and financial difficulties in Korea coastal shipping. (2) The excessive ship tonnage can be broken down into ship types as follows : oil carrier 250, 926 DWT(350%), cement carrier 9, 977 DWT(119%), iron material/machinery carrier 25, 665 DWT(117%), general cargo carrier 17, 416DWT(112%). (3) the current total ship crew of 5, 079 is more than the verified optimally efficient figure of 3, 808 by 1271. (4) From the viewpoint of management strategy, it is necessary that excessive ship tonnage be reduced and uneconomic outdated vessels be broken up. And its found that the diversion into economically efficient fleets is urgently required in order to meet increasing annual rate in the amounts of cargo(23, 877DWT). (5) The plans for the ship tonnage balance according to supply and demand are as follows 1) The establishment of a legislative system for the arrangement of ship tonnage. This would involve; (a) The announcement of an optimum tonnage which guides the licensing of cargo vessels and ship tonnage supply. (b) The establishment of an organization that substantially arrangement tonnage in Korea coastal shipping. 2) The announcement of an optimum ship tonnage both per year and short-term that guides current tonnage supply plans. 3) The settlement of elastic tariffs resulting in the protect6ion of coastal shipping's share from other tonnage supply plans. 4) The settlement of elastic tariffs resulting in the protection of coastal shipping's share from other transportation systems. 4) Restriction of ocean-going vessels from participating in coastal shipping routes. 5) Business rationalization of coastal shipping company which reduces uneconomic outdated vessels and boosts the national economy. If we are to achieve these ends, the followings are prerequisites; I) Because many non-licensed vessels are actually operating and threatening the safe voyage of the others in Korea coastal routes, it is necessary that those ind of vessels be controlled and punished by the authorities. II) The supply of ship tonnage in Korean coastal routes should be predently monitored because most of the coastal vessels are to small to be diverted into ocean-going routes in case of excessive supply. III) Every ship type which is engaged in coastal shipping should be specialized according to the characteristics of its routes as soon possible.

• 대한환경공학회지
• /
• 제30권3호
• /
• pp.302-313
• /
• 2008

본 연구는 포항지역 대기 중 PM$_{2.5}$의 물리 화학적 성분들의 농도분포특성을 파악하여 PM$_{2.5}$에 대한 배출원 기여도를 정량적으로 추정하고 PM$_{2.5}$농도 변동에 영향을 미치는 배출원을 알아보고자 하였다. 시료채취지점은 포항지역 내의 대조적인 두 지점인 공업지역과 주거지역에서 각 1개 지점을 선정하였다. 시료채취는 2003년 3월부터 12월에 걸쳐서 계절별 10$\sim$15일 동안 고용량공기시료채취기를 이용하여 24시간 연속 채취였다. PM$_{2.5}$ 시료에 함유된 화학성분들은 산추출하여 ICP와 이온크로마토그래피로 분석하였다. PM$_{2.5}$의 전체평균은 공업지역이 36.6 $\mu$g/m$^3$, 주거지역에서 30.6 $\mu$g/m$^3$로 나타났다. 계절별로는 두 지점 모두 봄철에 가장 높은 농도를 보이고 있으며 다음으로 겨울철, 가을철, 여름철의 순으로 나타났다. 두 측정지점에서 PM$_{2.5}$ 중 가장 많이 함유된 화학성분들은 이차생성입자를 형성하는 성분인 NO$_3^-$, SO$_4^{2-}$으로 나타났으며 각각의 농도는 공업지역에서 4.2 및 8.6 $\mu$g/m$^3$, 주거지역에서 3.7 및 6.9 $\mu$g/m$^3$로 나타났다. 반면, 공업지역에서는 Fe, Mn, Cr 등의 금속성분 농도가 주거지역에 비해 상당히 높게 나타나 공업지역이 철강산업의 영향을 반영하고 있는 것으로 추측된다. 포항지역 대기 중 PM$_{2.5}$의 농도 변동에 미치는 주요 영향인자를 파악하기 위하여 주성분 분석 및 다중회귀분석을 실시한 결과, 공업지역과 주거지역에서 가장 중요한 변수는 도로 비산먼지와 이차생성입자인 것으로 나타났으며, 이들 변수의 변동이 전체 PM$_{2.5}$ 농도변동에 가장 큰 영향을 미친다는 것을 알 수 있었다. 또한 포항지역 PM$_{2.5}$에 대한 주요 발생원의 기여도를 평가하기 위하여 CMB 모델링을 수행한 결과 공업지역의 경우 기여도가 큰 발생원은 토사 및 도로상의 비산먼지로 나타났고 그 다음으로 이차생성입자, 자동차, 해염입자, 금속산업의 순을 보였으며 주거지역도 이와 유사한 양상을 보였다. 이와 같은 결과를 토대로 국내에서 측정된 먼지시료를 대상으로 CMB 모델링 수행 시 그 적용한계성과 문제점 등을 고찰하였다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2012년도 제43회 하계 정기 학술대회 초록집
• /
• pp.80-81
• /
• 2012

Recently, one of the critical issues in the etching processes of the nanoscale devices is to achieve ultra-high aspect ratio contact (UHARC) profile without anomalous behaviors such as sidewall bowing, and twisting profile. To achieve this goal, the fluorocarbon plasmas with major advantage of the sidewall passivation have been used commonly with numerous additives to obtain the ideal etch profiles. However, they still suffer from formidable challenges such as tight limits of sidewall bowing and controlling the randomly distorted features in nanoscale etching profile. Furthermore, the absence of the available plasma simulation tools has made it difficult to develop revolutionary technologies to overcome these process limitations, including novel plasma chemistries, and plasma sources. As an effort to address these issues, we performed a fluorocarbon surface kinetic modeling based on the experimental plasma diagnostic data for silicon dioxide etching process under inductively coupled C4F6/Ar/O2 plasmas. For this work, the SiO2 etch rates were investigated with bulk plasma diagnostics tools such as Langmuir probe, cutoff probe and Quadruple Mass Spectrometer (QMS). The surface chemistries of the etched samples were measured by X-ray Photoelectron Spectrometer. To measure plasma parameters, the self-cleaned RF Langmuir probe was used for polymer deposition environment on the probe tip and double-checked by the cutoff probe which was known to be a precise plasma diagnostic tool for the electron density measurement. In addition, neutral and ion fluxes from bulk plasma were monitored with appearance methods using QMS signal. Based on these experimental data, we proposed a phenomenological, and realistic two-layer surface reaction model of SiO2 etch process under the overlying polymer passivation layer, considering material balance of deposition and etching through steady-state fluorocarbon layer. The predicted surface reaction modeling results showed good agreement with the experimental data. With the above studies of plasma surface reaction, we have developed a 3D topography simulator using the multi-layer level set algorithm and new memory saving technique, which is suitable in 3D UHARC etch simulation. Ballistic transports of neutral and ion species inside feature profile was considered by deterministic and Monte Carlo methods, respectively. In case of ultra-high aspect ratio contact hole etching, it is already well-known that the huge computational burden is required for realistic consideration of these ballistic transports. To address this issue, the related computational codes were efficiently parallelized for GPU (Graphic Processing Unit) computing, so that the total computation time could be improved more than few hundred times compared to the serial version. Finally, the 3D topography simulator was integrated with ballistic transport module and etch reaction model. Realistic etch-profile simulations with consideration of the sidewall polymer passivation layer were demonstrated.