• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2008.10a
• /
• pp.249-252
• /
• 2008

Micro V-notching process has been used to manufacturing the safety component in Li-Ion battery. These kinds of safety component in Li-Ion battery plays an important role in the explosion from excessive overheating. Therefore, it is very crucial to estimate accurately the working pressure range of the safety component with micro V-notch. In this study, the relationship with the working internal pressure in Li-Ion battery and fracture phenomenon in micro V-notch was investigated through the numerical analysis. The numerical analysis is especially adopted the finite element method with ductile fracture criteria.

• Journal of the Semiconductor & Display Technology
• /
• v.14 no.1
• /
• pp.39-43
• /
• 2015

This paper is to derive information about the optimal shape of the pack has a minimum temperature range of a Li-ion battery equipped with a module. We selected the shape of the pack in order to reduce the temperature deviation between the batteries as a variable. And we derived the experimental points with a minimum of DOE by D-optimal. We analyzed the temperature and the flow within the battery pack by using a numerical analysis verified in previous studies. We derive the equation for the temperature variation in the objective function using the RSM and performed optimization. As a result, it was confirmed that with the variation in the $1.706e-4^{\circ}C$ when to apply an optimized shape.

• Journal of environmental and Sanitary engineering
• /
• v.14 no.1
• /
• pp.80-87
• /
• 1999

According to the fact that algae, which is usually used as a biosorbent, contains chlorophyll, we used the chlorophyll as an adsorbent. In this study, chlorophyll is immobilized by agar, which was made of platan, oak, ginkgo and pine. We investigated the removing capacity of biosorbents to toxic heavy metals (Pb, CU, Cd, Zn) in the single ion solution. Then the experimental parameters were pH, reaction time and concentration of heavy metal ions.The optimum conditions for the adsorption of heavy metals were as follows : pH range was 4~5, reaction time was 40mon, and the highest ratio of the removing rate was 50~70 ppm. The order of the amount of Pb, Cu and Cd removed was specified as oak > ginkgo > pine > platan in these conditions and as pine > ginkgo > oak > platan at Zn. Fro the results of the desorption experiments, we found that the heavy metal with the highest ratio of desorption in the single ion adsorbent was Cu.

• Proceedings of the Korean Institute of Navigation and Port Research Conference
• /
• 2000.11a
• /
• pp.17-20
• /
• 2000

This study is about a retrograde triple well employed in the Cell tr. of next DRAM and flash memory. triple well structure is formed deep n-well under the light p-well using MeV ion implantation. MeV P implanted deep n-well was observed to show greatly improved characteristics of electrical isolation and soft error. Junction leakage current, however, showed a critical behavior as a function of implantation and annealing conditions. {311} defects were observed to be responsible for the leakage current. {311} defects were generated near the R$\sub$p/ (projected range) region and grown upward to the surface during annealing. This is study on the defect behavior in device region as a function of implantation and annealing conditions.

• Analytical Science and Technology
• /
• v.12 no.6
• /
• pp.583-586
• /
• 1999

The quantitative analysis of nitrate and nitrite in rain, milk and infant formula was done by Ion Chromatography. The nitrite was not detected(<0.1 mg/L) in all the samples. However, the nitrate was detected in the range of 0.1~4.9 mg/L in rain, 9.8~19.8 mg/L in milk, and 80~300 mg/L in infant formula, respectively. Some content of nitrate is close to the maximum contaminant level(MCL) which is 10 mg/L as $NO_3-N$, 44.3 mg/L as $NO_3$.

• Journal of Pharmaceutical Investigation
• /
• v.14 no.3
• /
• pp.131-135
• /
• 1984

The effect of pH and magnesium ion on the hydrolysis of dicyclomine HCl was investigated by comparing the rate constant and activation energy. The hydrolysis of dicyclomine HCl was acid-base catalytic reaction and the most stable range of pH was $3{\sim}5$. The magnesium ion accelerated the hydrolysis of dicyclomine HCl in aqueous solution.

• Journal of the Korean Applied Science and Technology
• /
• v.9 no.2
• /
• pp.119-126
• /
• 1992

The kinetics of the hydrolysis of indolylacrylophenone derivatives(IA) was investigated by ultraviolet spectrophotometry in 30% dioxane-$H_2O$ at 25$^{\circ}C$ Rate equations were obtained over a wide pH range. On the basis of rate equation, general base catalysis and Hammett's plot, the mechanism of hydrolysis to the (IA) were proposed: Below pH 3.0, the hydrolysis of (IA) was proportional to hydronium ion concentration, between pH 4.0${\sim}$9.0 neutral water molecule and hydroxide ion were added to carbon-carbon double bond and over pH 10.0 hydrolysis of (IA) was proportional to hydroxide ion concentration.

• Proceedings of the Korean Environmental Sciences Society Conference
• /
• 2003.11a
• /
• pp.109-112
• /
• 2003

A method to determine As(V) ions in aqueous solution by chemiluminescence method has been studied using a stopped flow system. The method is based on the increased chemiluminescence intensity with the addition of As(V) ion to a solution of lucigenin and hydrogen peroxide. The effects of KOH concentration, $H_2O_2$ concentration and flow rate of reagents on the chemiluminescence intensity have been investigated. The calibration curve for As(V) was linear over the range from $1.0{\times}l0^{-6}$M to $1.0{\times}l0^{-4}$M, the coefficient of correlation was 0.997 and the detection limit was $3.3{\times}l0^{-7}$M under the optimal experimental conditions.

• Proceedings of the KIEE Conference
• /
• 1995.11a
• /
• pp.472-474
• /
• 1995

A Sputter ion Plating(SIP) system with a r.f. coil electrode and the Facing Target Sputter(FTS) source was designed for high-quality thin film formation. The rf discharge was combined with DC facing target sputtering in order to enhance ionization degree of a sputtered atoms. The energy of ions incident on the substrate depended on the health potential of DC biased substrate. The mean impact ion energy increased with negative bias voltage and rf power. The adhesive force of the TiN film formed was in the range of 30$\sim$50N, and markedly influenced by substrate bias voltage.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.2 s.179
• /
• pp.97-103
• /
• 2006

In this paper, effect of temperature in TiN-coating by arc ion plating on surface characteristics of a TiN coated high speed steel is investigated by experiments. Hardness, surface roughness, TiN-coating thickness and adsorption force are measured in order to evaluate the effects. For evaluation of the experimental data, one-way ANOVA method is used. It is concluded that the furnace temperature in the range $400^[\circ}C\~500^{\circ}C$ in AIP processing has a little influence on the TiN coating of the SKH51 steels.