• Journal of Ocean Engineering and Technology
• /
• v.23 no.3
• /
• pp.20-29
• /
• 2009

This study investigated the shear strength characteristics of waste tire powder-added lightweight soil (WTLS), which were developed to recycle dredged soil, bottom ash, and waste tires. The WTLS used in this experiment consisted of dredged soil, bottom ash, waste tire powder, and cement. Test specimens were prepared with various contents of waste tire powder ranging from 0% to 100% at 25% intervals and bottom ash contents of 0% or 100% by the weight of the dry dredged soil. In this study several series of direct shear tests were carried out, which indicated that the shear properties of WTLS were strongly influenced by the mixing conditions, such as the waste tire powder content and bottom ash content. The unit weight, as well as the shear strength of the WTLS, decreased with an increase in waste tire powder content. The shear strength of WTLS with bottom ash was 1.34 times greater than that of WTLS without bottom ash. An average increase in cohesion of 30 kPa was obtained in WTLS with the inclusion of bottom ash due to the bond strength induced from the pozzolanic reaction of the bottom ash. In this test, the maximum value of the internal friction angle was obtained with a 25% content of waste tire powder.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.5
• /
• pp.68-75
• /
• 2010

The one of the major problems in the development of PEMFC was regarding to the assurance of sealing on stack. The failure on the sealing creates the problems of fuel leakage, mixing, internal combustion, damage on parts and can be a direct reason for the degrading the efficiency of fuel cell. This paper studies on the analytical approach for improving the contacting pressure distribution on the gasket at the evaluation on the sealing of fuel cell stack. So, the assembly analysis on multi layered fuel cell stack was performed. The research on the simplification of finite element model was performed for three dimensional analysis at the multi layered state. The improved contact pressure distribution was obtained through the case studies on gasket for better sealing. In addition, the number of the cell was determined for the effective analysis and the structural characteristics were evaluated based on this research.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.22 no.6
• /
• pp.120-127
• /
• 2014

Robustness and controllability are the key factors in internal combustion engine commercialization. This study focuses on the combustion strategy to commercialize the low temperature diesel combustion technology. Various LTC combustion methods such as PPCI, MK and highly diluted mixing controlled LTC were conducted on 6.0L heavy duty diesel engine. To find the best feasible LTC strategy, emission level, fuel consumption and combustion safety during the combustion mode change were considered. Experiments were carried out under various engine operating conditions; engine speed & load, EGR level, injection timing. Finally, this study suggests realizable LTC combustion strategy; moderate EGR level and slight early injection are possible to considerably lower PM, NOx emission and expand LTC operating range up to 50% load without CO and HC emission.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.7
• /
• pp.529-535
• /
• 2008

The characteristics of combustion process in an internal combustion engine are affected by the mixing process between injected fuel and ambient gas. Therefore, it is necessary to understand the mixture formation process of diesel spray. In this study, the spray structure was visualized by the exciplex fluorescence method, which can provide the simultaneous 2-D images of vapor and liquid phase in inner spray. For accurate investigation, the liquid-phase images were recorded with a 35mm still camera and CCD camera. Consequentially, it could be confirmed that the high-concentration vapor phase is formed in the region of spray tip and the edge of the liquid phase where droplets exist in the evaporating diesel spray, and the formed vapor is spread by diffusion. Also, the distribution of vapor is determined by the motion of droplets that exist in the edge of the liquid phase and the spray-tip region.

• Fashion & Textile Research Journal
• /
• v.15 no.4
• /
• pp.493-503
• /
• 2013

This study analyzes expression methodology and aesthetic meanings in modern hair ornaments that adopt maximalism. Maximalism has appeared in various hair ornaments throughout history. Hair dresses are used for many reasons related to class, social position, religious beliefs, and occupation throughout the Eastern and Western hemispheres. A higher class and social position was often denoted by a fancier and bigger hairdress. In modern society maximalism is expressed in literature, expressionism, maxi-marketing, exaggerative advertisements, and symbolic architecture. Formative expression methodologies in modern hair ornaments that adopt maximalism are transform, overlapping & exaggeration, and mixing & edition. The aesthetic meanings of maximalism in hair ornaments are the reinterpretation of retro ornaments, the exaggeration of internal self-expression, humorous symbolic objects, and the conveyance of a social critical message. The advantages of maximalism help people communicate and co-provide an abundant life. These are expected to create significant and numerous positive impacts in society. In addition, the continued efforts on the investment in hair ornaments that express Maximalism well as a fashion trend shows that further study on the persistence, practicality and recognized design inconvenience in the aesthetic value are needed.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.2
• /
• pp.136-142
• /
• 2015

The shell and tube heat exchanger is an essential part of a power plant for recovering transfer heat between the feed water of a boiler and the wasted heat. The baffles are also an important element inside the heat exchanger. Internal materials influence the flow pattern in the bed. The influence of baffles in the velocity profiles was observed using a three-dimensional PIV (Particle Image Velocimetry) around baffles in a horizontal circular tube. The velocity of the particles was measured before the baffle and between them in the test tube. Results show that the velocity vectors near the front baffle flow along the vertical wall, and then concentrate on the upper opening of the front baffle. The velocity profiles circulate in the front and rear baffle. These profiles are related to the Reynolds number (Re) or the flow intensity. Velocity profiles at lower Re number showed complicated mixing to obtain the velocities and concentrate on the lower opening of the rear baffle as front wall. Numerical simulations were performed to investigate the effects of the baffle and obtain the velocity profiles between the two baffles. In this study, a commercial CFD package, Fluent 6.3.21 with the turbulent flow modeling, k-${\epsilon}$ are adopted. The path line and local axial velocities are calculated between two baffles using this program.

• 한국신재생에너지학회:학술대회논문집
• /
• 2009.06a
• /
• pp.731-734
• /
• 2009

KIER has been developed a compact and highly efficient fuel processor which is one of the key component of the residential PEM fuel cells system. The fuel processor uses methane steam reforming to convert natural gas to a mixture of water, hydrogen, carbon dioxide, carbon monoxide and unreacted methane. Then carbon monoxide is converted to carbon dioxide in water-gas-shift reactor and preferential oxidation reactor. A start-up time of the fuel processor is about 1h and CO concentration among the final product is maintained less than 5 vol. ppm. To achieve high thermal efficiency of 80% on a LHV basis, an optimal thermal network was designed. Internal heat exchange of the fuel processor is so efficient that the temperature of the reformed gas and the flue gas at the exit of the fuel processor remains less than $100^{\circ}C$. A compact design considering a mixing and distribution of the feed was applied to reduce the reactor volume. The current volume of the fuel processor is 17L with insulation.

• Journal of the Korean Professional Engineers Association
• /
• v.18 no.2
• /
• pp.6-15
• /
• 1985

A new process disregraded the H$_2$SO$_4$ treatment process heretofore in use, was developed and substituted for mineral base engine used oil of homemade SAE-30 grade H.V.I., which was used covering 4,500km, as samples, and the following results in research, was obtained. (1) A good quality of rerefinded base oil was obtained through roughly a course of developed processes of vacuum distillation process, solvent extraction process, neutralization treatment process and clay treatment process. (2) Through vacuum distillation process, the size of fine grains of insoluble colloid carbon that is, colloid carbon which was produced by burning of internal combustion engine oil and fuel, could be brought up and precipitated (3) The insoluble matters and admixtures could be easily dispersed and dissolved by mixing and extracting solvent disregarded the H$_2$SO$_4$ treatment process heretofore in use (4) waste matter heretofore called acid sludge in consequence of the process, did not appear at all. accordingly, the environmental pollution could be removed. (5) The troubles of corrosion to copper strip which was faults of the usual used oil refined products and peculiar offensive odor of the rerefined oil, could be solved through the neutralization process. (6) The yield of rerefined oil obtained through a course of processes was over 86 percent, and it is of practical use, not to speak of commercial value.

• International Journal of Automotive Technology
• /
• v.1 no.2
• /
• pp.95-100
• /
• 2000

The droplet and the turbulent characteristics of a counterflowing internal mixing pneumatic nozzle mainly focused. The measurements were made using a Phase Doppler Particle Analyzer under the different air pressures. The nozzle with tangential-drilled holes at an angle of 30 to the central axis has been designed. The spatial distributions of velocities, fluctuating velocities, droplet diameters and SMD were quantitatively and qualitatively fluctuating velocities were substantially higher than the radial and the tangential ones. This implies that the disintegration process is enhanced with the higher air pressure. The larger droplets were detected near the spray centerline at the upstream while the smaller ones were generated at the downstream. This was attributed to the lower rates of spherical particles which were not subject to instantaneous breakup. However, substantial increases in SMD from the central part tower spray periphery were predictable in downstream regions.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.197-201
• /
• 2006

In the development process of a fuel-rich gas generator using kerosene and LOx for a 30 tonf class liquid rocket engine, a heat damage occurred at the LOx post of swirl coaxial injectors used in the gas generator and the problem has been examined. To prevent the heat damage, injectors are redesigned to have an increased recess while maintaining internal mixing, which minimizes recirculation region to prevent anchoring of the flame in the recirculation region. The combustion test results of the sub-scale gas generator showed that this scheme can prevent heat damage of the LOx post in the swirl coaxial injectors of the fuel-rich gas generator.