• 대한기계학회논문집A
• /
• 제20권8호
• /
• pp.2524-2539
• /
• 1996

A design process and an axisymmetric boundary integral equation method for precise structural analysis of the aircraft gas turbine rotor disk were developed. This axisymmetric boundary integral equation method for stress and steady-state thermal analysis was improved in solution accuracy by appling an implicit technique for Cauchy principal value evaluation, a subelement technique for weak singular integral evaluation and a double exponentical integral technoque for internal point solution near boundary surfaces. Stresses, temperatures, low cycle fatigue lifes and critical speeds for the turbine rotor disk of the thrust 1421 N class turbojet engine were analysed in a pratical calculation model problem.

• 소음진동
• /
• 제9권2호
• /
• pp.401-408
• /
• 1999

A method is presented for the vibration analysis of steam turbine-generator rotor system based on the component mode synthesis method. The motion of each component of the system is described by superposing constraint mode associated with boundary coordinates and constrained normal modes associated with internal coordinates. This method using real fixed-interface modes allows for significant reduction in system model size while retaining the essential dynamic characteristics of the lower modes. The capability of this method is demonstrated in the natural frequency and unbalance response analysis of the steam turbine-generator rotor system in which the dynamics of the pedestal is considered. The results by the present method are compared with finite element method and trnasfer matrix method in terms of the accuracy and computing time.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.1715-1720
• /
• 2004

This paper presents the characteristics of internal clearances for the interstage of blades and shaft gland seals on the steam turbine which are installed in tandem compound. Internal clearances was changed when the rotor turned in the cylindrical sleeve bearing due to the generation of oil film wedge. This presented concern is very useful to prevent the rubbing damage of seal edge between the fixed and moving parts in steam turbine due to the misalignment at the rotating and stationary parts. This method is applied for the unbalanced clearances distribution to the left and right sides in the turbine casing. A considerable amount of unbalanced clearances distribution trend is determined according to the rotating speed of rotor, size and type of proceeding bearing, oil viscosity, surface roughness of bearing and shaft, oil temperature, oil pressure and bearing load.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권6호
• /
• pp.687-693
• /
• 2007

It has been known that one of the main obstacles of improving the performance of positive displacement hydraulic turbine is pressure pulsation which occurs at the regions upstream and downstream of the turbine. In order to suppress the pressure pulsation. occurrence reason of the pressure pulsation should be understood in detail Therefore. this study aims to establish a CFD analysis method by which the phenomena of unsteady pressure pulsation can be examined with high accuracy. Internal flow field of the turbine is modeled simply to generalize the relation between the pressure pulsation and internal flow. The results show that the Present CFD method adopting unsteady calculation can be applied successfully to the analysis of the Phenomena of Pressure Pulsation. Occurrence of the Pressure pulsation is due to the difference of the rotational speed of turbine rotors When driving rotor rotates by uniform speed and fellowing rotor rotates by variable speed, very large Pressure pulsation occurs within the turbine periodically.

• 한국수소및신에너지학회논문집
• /
• 제23권6호
• /
• pp.688-695
• /
• 2012

The present study represents the effects of boundary condition on the performance of a centrifugal blower at the interference plane between rotational and stationary domains using three dimensional compressible Navier-Stocks equations. Two boundary conditions, frozen-rotor and stage, are compared to analyze the blower performance. Installation angle between the cutoff of a volute casing and a impeller blade is also introduced to evaluate the blower performance and to understand the internal flow inside the blower. Throughout numerical simulation, it is found that the frozen rotor interface method at the interference plane represents well the variations of flow field inside the blower compared to stage interface method. However, pressure has maximum two percent error according to the installation angles while pressure is almost constant for the stage interface method. And stage interface method can relatively well predict the blower performance. Detailed internal flows of the centrifugal blower are compared and analyzed by numerical simulation.

• Journal of Magnetics
• /
• 제21권2호
• /
• pp.249-254
• /
• 2016

Recently, electric vehicles have got significant attention because it is more eco-friendly and efficient than internal combustion engine vehicles. Instead of an internal combustion engine, the electric vehicle has a motor for propulsion. The permanent magnet synchronous motor which has permanent magnet instead of field winding in the rotor has especially higher efficiency and power density than other types of motor. When the irreversible demagnetization is occurred, drivers are exposed to high risk of accident by the fault operation of motor. Therefore, the irreversible demagnetization of permanent magnet should be detected to reduce the risk of accident. In this study, the demagnetization diagnosis method based on the result of locked rotor test is proposed. Based on short measurement time, the proposed diagnosis method aims to detect the demagnetization fault when an electric vehicle is at a complete standstill. The proposed method is verified through the finite element analysis.

• 한국유체기계학회 논문집
• /
• 제14권5호
• /
• pp.18-23
• /
• 2011

A CFD analysis method is developed and applied for investigating the gas flow and the byproduct particle trajectory in Roots type vacuum pump. The internal fluid flow and thermal fields between the rotors and the housing of vacuum pump are analyzed by using the dynamic mesh, the numerical methods for unsteady 2-D Navier-Stokes equation and the standard k-$\varepsilon$ turbulence model of the Fluent code. Coupled with the flow simulation results, the particle trajectory of the byproduct flowing into the pump with gas stream is analyzed by using discrete phase modeling technique. The CFD analysis results show the pressure, the velocity and the temperature distributions in pump change abruptly due to the rotation of rotors, and back flows are produced due to the strong reverse pressure gradients at rotor/rotor and rotor/housing clearances. The predicted byproduct particle trajectory results also show the particles impinge on the clearance surfaces between the housing and the rotor of pump and then may form the deposit layer causing the failure of pump.

• 대한기계학회논문집A
• /
• 제39권2호
• /
• pp.169-177
• /
• 2015

내접형 기어펌프에 사용되는 지로터의 경우, 소결 공정기술의 발달로 복잡한 형상의 가공이 용이하며 내구성과 소형화의 장점이 있으나, 자동차의 연비효율 개선을 위한 유량증대 및 소음저감을 위한 연구가 요구되고 있다. 본 논문에서는 기존의 병진이동에 의한 지로터 치형의 형상조합 알고리즘이 가지는 형상 불연속성을 개선하기 위하여 회전이동 및 병진이동을 이용한 형상조합 알고리즘을 개발하였으며, 이를 토대로 개발된 설계 프로그램을 이용하여 3-타원이 조합된 경우와 타원 1-인벌루트-타원 2 이조합된 경우에 대해 치형형상을 도출하고, 형상에 따른 로터의 주요성능(유량, 유량맥동, 미끄럼률 및 압력각)을 계산하였다. 해석결과를 토대로 조합된 치형형상에 대한 최적설계를 수행하였으며, 기존 치형과의 성능 비교를 통하여 설계의 타당성을 검증하였다.

• Tribology and Lubricants
• /
• 제12권3호
• /
• pp.100-106
• /
• 1996

Gerotor pumps and motors are widely used in lubrication and hydraulic actuator systems. Compared with internal gear pumps and motors, they have many advantages. However, the gerotor profiles have not been suff'lciently analyzed theoretically. Therefore, it is very difficult for designer to decide the specifications of the gemtor profiles, and calculation of flow rate and minimum distance of clearance in the contact point of inner and outer rotor is not yet confirmed. In this paper, when we design inner and outer rotor concurently, we have analyzed the gerotor profiles and displayed the calculated results such as flow rate, minimum distance between inner and outer rotor and gerotor profiles.

• 대한전기학회논문지
• /
• 제36권10호
• /
• pp.703-712
• /
• 1987

A position detection method for 2 phase bifilar permanent magnet step motors is proposed. The back emfgenerated on 2 phase windings by rotor permanent magnet is calculated using motor terminal voltage and current by analog circuit, and the rotor position output is obtained from tese back emf signals through some logical manipulation circuit. This position detector functionally acts like a 2 channel optical incremental encoder, and it is also shown by experimental results that it works well over wide range of speed or under resonant condition where the rotor rings around the detent position. Its resolution is twice of the number of steps per revolution. Bu software implemented on micro-processor, the reliability of position output is enhanced, detecting and correcting error dut to external and/ or internal noise.