• Journal of Biosystems Engineering
• /
• 제12권1호
• /
• pp.45-52
• /
• 1987

엔진의 점화시기(點火時期)를 제어(制御)하는 데에 마이크로컴퓨터를 이용(利用)하고자 여러 종류(種類)의 제어장치(制御裝置)를 설계(設計) 제작(製作)하여 가동시험한 결과를 요약하면 다음과 같다. 가. 제어장치(制御裝置)의 제작시(製作時) 고압방전(高壓放電)에 의한 잡음(雜音), 서어지, 전자파(電磁波)로부터 디지탈회로와 컴퓨터의 기능(技能)이 교란되는 것을 방지하기 위하여는 고압회로(高壓回路)와 여타 회로와의 분리 및 고압회로의 기생발진 억제와 차폐가 완전하여야 할 것이며, 또한 양질의 점화용(點火用) 도선(導線)을 사용하여야 할 것으로 생각된다. 나. 본 실험의 범위내에서는(컴퓨터시스템) (써어보 기구에 의한 점화신호발생(點火信號發生) 및 제어(制御) - (트랜지스터 스위칭) - (고압회로) 로 구성(構成)시킨 점화시기제어장치가 컴퓨터 등의 기능교란을 일으키지 않고 가장 잘 작동(作動)되었다. 다. 본 실험의 결과(結果)를 기초(基礎)로 마이크로컴퓨터를 이용한 엔진의 최적점화진각제어(最適點火進角制御)에의 응용(應用)이 가능(可能)할 것으로 사료(思料)된다.

• 한국농공학회논문집
• /
• 제57권5호
• /
• pp.19-27
• /
• 2015

The results of Saemangeum seadike field inspection and material testing of armor stones in order to analyze causes of abrasion according to material characteristics of seaside armor stones in Saemangeum seadike are in the following: 1. The armor stones in Saemangeum seadike have been constructed by using internal stones (mainly, sinsi stones) and external stones, which had less strength (77.3 %) and more abrasion rate (133.3 %) compared with sinsi stones. 2. The compressive strength and abrasion rate were compared between ordinary wave section and high wave section for the purpose of analyzing the influence of waves. In compressive strength, sinsi stones were 4.0 % stronger and external stones were 0.6 % stronger in ordinary wave section than those of high wave section in average. In the case of abrasion rate, sinsi stones were 3.0 % higher and external stones were 8.2 % higher in the high wave section than those in the ordinary section. 3. The result of comparing compressive strength according to a zone is that the compressive strength in the Intertidal area was less strong in most of the zones. 4. Considering that deviated stones are moving around over the surface of armor stones in situ, it is important to compare material characteristics. So the comparison test about this factor showed that deviated sinsi stones were stronger than armor stones in situ in terms of compressive strength and resistance to abrasion. Based on these results, abraded armor stones may have resulted from their durability. Therefore it is assumed that armor stones are likely to be abraded when deviated stones which are more durable are moving around over armor stones which are less durable.

• 한국자동차공학회논문집
• /
• 제5권2호
• /
• pp.50-59
• /
• 1997

When a front head of train enters a tunnel at a high speed, compression wave is generated at tunnel entrance due to the confinement effect and propagated along the tunnel with sound of speed. The propagated compression wave is reflected at tunnel exit due to abrupt pressure change at passage. The reflected wave is expansion pressure wave. And when the rear head of train goes through the tunnel entrance, another expansion pressure wave is generated and propagated along the tunnel. The pressure drop occurs seriously around train when the two expansion pressure waves come cross on train in the tunnel. In order to reduce the pressure drop, the compression wave front must be controlled because the intensity and magnitude of pressure drop is nearly proportional to that of compression wave at tunnel entrance. This study relates to reduction of the pressure wave gradient with respect to tunnel entrance shape change with various kind of angle and rounding. The results show characteristics of wave propagation in tunnel, usefulness of characteristic curve to estimate proper time domain size in numerical study and measuring time in actual experiment. Also rounding is contributed to improve pressure wave front even if its radius is very small at tunnel entrance. In order to improve of pressure wave front at tunnel entrance, proper angle is prefered to rounding with big radius and an angle of around 14$^{\circ}$ is recommended according to this simulations, And it is expected to reduce additional pressure drop in tunnel when the location and the size of the internal space for attendant equipment are considered in advance.

• 한국철도학회논문집
• /
• 제17권2호
• /
• pp.100-105
• /
• 2014

해중철도 부근에서 테러나 사고에 의해 수중폭발이 발생하였을 경우, 함체에 치명적인 손상을 가할 수 있으므로, 충분한 강도를 확보해야 한다. 본 연구에서는 설계 목적으로 해중철도 인근에서 수중폭발이 발생한 경우, 경험에 기초한 공식을 이용하여 충격압을 추정하고, 충격압에 의한 해중철도의 응답을 해석할 수 있는 간이 해석 방법을 제안하였다. 해중철도 함체를 탄성 지지된 보로 이상화하고, 초기 최대 충격압이 작용하는 보에 대해 정적 유한요소해석을 실시한 후, 동하중 계수와 조합함으로 최대 변위 및 굽힘 모멘트를 계산한다. 간이해석 결과는 상용 유한요소해석 소프트웨어를 이용한, 시간에 따른 과도응답해석 결과와 비교하여 양호한 일치를 보임을 확인하였다.

• Structural Engineering and Mechanics
• /
• 제66권1호
• /
• pp.45-59
• /
• 2018

The bi-material elastic system consisting of the pre-stressed hollow cylinder and pre-stresses surrounding infinite elastic medium is considered and it is assumed that the mentioned initial stresses in this system are caused with the compressing or stretching uniformly distributed normal forces acting at infinity in the direction which is parallel to the cylinder's axis. Moreover, it is assumed that on the internal surface of the cylinder the ring load which moves with constant velocity acts and within these frameworks it is required to determine the influence of the aforementioned initial stresses on the critical velocity of the moving load. The corresponding investigations are carried out within the framework of the so-called three-dimensional linearized theory of elastic waves in initially stresses bodies and the axisymmetric stress-strain state case is considered. The "moving coordinate system" method is used and the Fourier transform is employed for solution to the formulated mathematical problem and Fourier transformation of the sought values are determined analytically. However, the originals of those are determined numerically with the use of the Sommerfeld contour method. The critical velocity is determined from the criterion, according to which, the magnitudes of the absolute values of the stresses and displacements caused with the moving load approaches an infinity. Numerical results on the influence of the initial stresses on the critical velocity and interface normal and shear stresses are presented and discussed. In particular, it is established that the initial stretching (compressing) of the constituents of the system under consideration causes a decrease (an increase) in the values of the critical velocity.

• 한국전자파학회논문지
• /
• 제28권2호
• /
• pp.155-158
• /
• 2017

전자, 통신 기술의 발달로 대부분의 장소에서 전자기기가 존재한다. 자동차, 열차, 항공기 등 다양한 장소에서 전자기기의 활용이 증가된 만큼 고출력 전자기파로 인한 오작동과 하드웨어의 치명적인 손상을 확인할 수 있는 안전성을 연구하는 것이 중요하게 되었다. 구조물 내부에 전자기기 및 여러 센서를 연결하는 케이블은 전자기파에 의한 오작동을 초래할 수 있는 원인 중 하나이기 때문에 전자파 영향에 대한 해석이 필수적이다. 본 논문에서는 상관관계 함수와 전송이론을 이용하여, 전기적으로 큰 공진기 내부에 존재하는 케이블에 유기되는 전류를 계산해 외부 전자기파에 의한 영향을 해석하였다.

• Journal of Mechanical Science and Technology
• /
• 제20권8호
• /
• pp.1256-1265
• /
• 2006

The supersonic flows around tandem cavities were investigated by two-dimensional and three-dimensional numerical simulations using the Reynolds-Averaged Navier-Stokes (RANS) equation with the k- ω turbulence model. The flow around a cavity is characterized as unsteady flow because of the formation and dissipation of vortices due to the interaction between the freestream shear layer and cavity internal flow, the generation of shock and expansion waves, and the acoustic effect transmitted from wake flow to upstream. The upwind TVD scheme based on the flux vector split with van Leer's limiter was used as the numerical method. Numerical calculations were performed by the parallel processing with time discretizations carried out by the 4th-order Runge- Kutta method. The aspect ratios of cavities are 3 for the first cavity and 1 for the second cavity. The ratio of cavity interval to depth is 1. The ratio of cavity width to depth is 1 in the case of three dimensional flow. The Mach number and the Reynolds number were 1.5 and $4.5{\times}10^5$, respectively. The characteristics of the dominant frequency between two- dimensional and three-dimensional flows were compared, and the characteristics of the second cavity flow due to the first cavity flow was analyzed. Both two dimensional and three dimensional flow oscillations were in the 'shear layer mode', which is based on the feedback mechanism of Rossiter's formula. However, three dimensional flow was much less turbulent than two dimensional flow, depending on whether it could inflow and outflow laterally. The dominant frequencies of the two dimensional flow and three dimensional flows coincided with Rossiter's 2nd mode frequency. The another dominant frequency of the three dimensional flow corresponded to Rossiter's 1st mode frequency.

• 한국추진공학회지
• /
• 제22권2호
• /
• pp.52-58
• /
• 2018

유체 유동 시스템에서 히스테리시스 현상은 다양한 산업 및 공학 응용 분야에서 발생하며, 최근 이에 대한 많은 연구가 수행되어 왔다. 이러한 현상은 주로 압력비가 일시적으로 변화하는 과정에서 발생하며 초음속 풍동에 영향을 미칠 것으로 예상되나, 이에 대한 연구는 찾아보기 힘들다. 본 연구에서는 초음속 풍동 내부에서 발생하는 히스테리시스 현상을 수치해석으로 조사하였다. 비정상, 축대칭, 압축성 N-S 방정식을 유한 체적법으로 이산화 하였으며, 난류모델은 Spalart-Allmaras을 적용하였다. 본 연구의 결과로 전압의 증감에 따라, 동일한 압력비에서 발생하는 충격파의 위치가 다르게 나타났으며, 이를 통해 초음속 풍동을 효율적으로 작동시킬 수 있는 최적의 압력비를 찾을 수 있음을 알았다.

• 대한조선학회논문집
• /
• 제31권4호
• /
• pp.73-81
• /
• 1994

선박 내항성능의 3차원적 해석을 위하여 3차원 판넬 방법을 이용한 쏘오스 분포법과 쏘오스-다이폴 분포법이 널리 이용되어 왔다. 그러나, 이 방법들을 이용하는 경우에는 내부 유동에 의한 자유표면의 공진현상에 의해 특이파수(irregular frequency)라고 불리는 파주파수에서 동유체력 계산에 큰 오차가 발생하게 되며 이런 현상을 제거하는 것은 정확한 내항성능 해석에 필수적이라 할 수 있다. 본 논문에서는 전진동요하는 선박의 운동 해석을 위하여 Wu등이 유도한 전진하면서 동요하는 Green 함수를 이용하였다. Green함수의 계산을 위하여는 어뎁티브(adaptive) 적분방법과 스트레칭(stretching) 변환 및 정류위상(stationary phase) 적분 방법을 사용하였으며 선체의 표면과 선체 내부 수선면에 특이점을 분포한 적분방정식을 도출하였다. 또한 2차원 문제를 다룬 Ohmatsu의 제안에 따라 내부 수선면에서 법선속도가 0이라는 조건을 이용하여 동요하는 문제의 불규칙파수 현상을 제거할 수 있었다. 계산은 Series 60($C_B=0.7$)에 대하여 수행되었으며 부가질량 계수, 감쇠 계수 및 파랑강제력에 대하여 기존의 연구 결과 및 실험 결과와 비교하였다.

• 한국어학
• /
• 제71권
• /
• pp.1-22
• /
• 2016

The early 20th century is a period of time when Korea confronted with the surging waves of modernization, and made a variety of internal reactions. The Korean language, not immune to the upheaval, also experienced new changes and gradually gained characteristics of today's Korean. Although scholars have not yet fully agreed upon the time division of Korean, Gabo reformation (1896) is usually considered to be the beginning of modern Korean. Thus, the early 20th century was also the beginning of modern Korean. Phonological, lexical, and grammatical characteristics of modern day Korean began to appear during this period of time. Phonologically, the 10 vowel system was established, glottal sounds and aspirated sounds increased, vowel harmony declined. Phenomena such as vowel raising, front-vowelization, monophthongization, and the word-initial rule appeared. Meanwhile, hangul-Chinese mix writing became common practice, and hangul-only writing also started to take place in narrative writing, and elements of spoken language began to reflect in written language. All those pointed to the unification of written and spoken language. Under the influence of modernization, a great amount of new words appeared. Especially, Japanese and other foreign words flooded in in great quantities. Grammatically, '-eos-(-엇-), -neun-(-는-), -ges-(-겟-)' trichotomy system of tenses was established, and hearer-oriented honorific system also formed a binary system of 'hasoseo(하소서), hasibsio(하십시오), hao(하오), hage(하게), haera(해라)' and 'hae (해), haeyo(해요)'. In word formation and sentence construction, the use of '-gi(-기)' became more frequent than '-eum(-음)', while '~geot(~것)' also significantly increased. In negative, causative and passive expressions, the use of long form, which has fewer restrictions than the short form, became more frequent. A tendency towards simplicity appeared. In the same vain, long and complex sentences with several clauses tend to be avoided. Instead, short simple sentences became more favorable. Korean linguistics scholars should pay closer attention to the modernization period, which includes the early 20th century. In order to fully understand today's Korean language, more thorough research on this immediately preceding period is necessary.