• Nuclear Engineering and Technology
• /
• v.55 no.8
• /
• pp.3017-3029
• /
• 2023

In the late in-vessel phase of a nuclear reactor severe accident, the internal heat transfer and crust evolution during the debris bed melting process have important effects on the thermal load distribution along the vessel wall, and further affect the reactor pressure vessel (RPV) failure mode and the state of melt during leakage. This study coupled the phase change model and large eddy simulation to investigate the variations of the temperature, melt liquid fraction, crust and heat flux distributions during the debris bed melting process in the hypothetical severe accident of HPR1000. The results indicated that the heat flow towards the vessel wall and upper surface were similar at the beginning stage of debris melting, but the upward heat flow increased significantly as the development of the molten pool. The maximum heat flux towards the vessel wall reached 0.4 MW/m². The thickness of lower crust decreased as the debris melting. It was much thicker at the bottom region with the azimuthal angle below 20° and decreased rapidly at the azimuthal angle around 20-50°. The maximum and minimum thicknesses were 2 and 90 mm, respectively. By contrast, the distribution of upper crust was uniform and reached stable state much earlier than the lower crust, with the thickness of about 10 mm. Moreover, the sensitivity analysis of initial condition indicated that as the decrease of time interval from reactor scram to debris bed dried-out, the maximum debris temperature and melt fraction became larger, the lower crust thickness became thinner, but the upper crust had no significant change. The sensitivity analysis of in-vessel retention (IVR) strategies indicated that the passive and active external reactor vessel cooling (ERVC) had little effect on the internal heat transfer and crust evolution. In the case not considering the internal reactor vessel cooling (IRVC), the upper crust was not obvious.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2003.03a
• /
• pp.789-796
• /
• 2003

A reliability analysis is performed to investigate the influence of the uncertainty from the limited in-situ samples and the inherent heterogeneity of the ground on the probability of piping for the marine embankment near shore. The result are compared with those of the deterministic piping stability analysis performed using the fininte element flow analysis. The random variables used are hydraulic conductivity of the ground subsurface and embankment, and the water level of both internal and external side of the embankment. The probability of piping is most sensitive to the mean and standard deviation of internal water level of the embankment among the random variables included in the reliability analysis. It is found that the lower limits of internal water level which satisfies the allowable proability of piping failure for the embankment studied were E.L(-) 1.83m and E.L(-) 1.48m during and after the construction of the embankment, respectively.

• Proceedings of the SAREK Conference
• /
• 2008.11a
• /
• pp.157-164
• /
• 2008

The temperature-entropy diagram of water or vapor displays graphically the thermophysical properties, so it is very conveniently used in various thermal systems. On general T-s chart of water, there are temperature, pressure, quality, specific volume, specific enthalpy, specific entropy. However, various state and process values besides above properties can be plotted on T-s diagram. In this study, we developed the software drawing twenty six kinds of properties, that is temperature, pressure, quality, specific volume, specific internal energy, specific enthalpy, specific entropy, specific exergy, exergy ratio, density, isobaric specific heat, isochoric specific heat, ratio of specific heat, coefficient of viscosity, kinematic coefficient of viscosity, thermal conductivity, prandtl number, ion product, static dielectric constant, isentropic exponent, velocity of sound, joule-thomson coefficient, pressure coefficient, volumetric coefficient of expansion, isentropic compressibility, and isothermal compressibility. Also, this software can analyze and print the system values of mass flow rate, volume flow rate, internal energy flow rate, enthalpy flow rate, entropy flow rate, exergy flow rate, heat flow rate, power output, power efficiency, and reversible work. Additionally, this software support the functions such as MS-Power Point.

• Journal of the Semiconductor & Display Technology
• /
• v.10 no.1
• /
• pp.1-6
• /
• 2011

In this paper, the air flow induced by the rotating flat disk is numerically investigated in a hope to better understand the air flow structures inside the wax spin coater for a silicon wafer polishing station. Due to the complex inner geometry of actual spin coater such as the casing around the rotating ceramic block and servo motor, recirculation of air flow is inevitably found on the coating target if the internal space of spin coater is closed at the bottom and it could be the possible source of contamination on the wax coating. By numerical flow simulation, we found that it is necessary to install the air vent at the bottom and to apply the sufficient air suction in order to control the path of air flow and to eliminate the air recirculation zone above the spinning surface of coating target.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.8
• /
• pp.1201-1207
• /
• 2008

Numerical analysis information will be very useful to improve fluid system. General information about an internal gas flow is presented by numerical analysis approach. Relating with hydrogen compressing system, which have an important role in hydrogen energy utilization, this should be a useful tool to observe the flow quickly and clearly. Flow characteristic analysis, including pressure and turbulence kinetic energy distribution of hydrogen gas coming to the cylinder of a reciprocating compressor are presented in this paper. Suction-passage model is designed based on real model of hydrogen compressor. Pressure boundary conditions are applied considering the real condition of operating system. The result shows pressure and turbulence kinetic energy are not distributed uniformly along the passage of the Hydrogen system. Path line or particles tracks help to demonstrate flow characteristics inside the passage. The existence of vortices and flow direction can be precisely predicted. Based on this result, the design improvement, such as reducing the varying flow parameters and flow reorientation should be done. Consequently, development of the better hydrogen compressing system will be achieved.

• The Journal of Korean Medicine
• /
• v.20 no.1 s.37
• /
• pp.91-105
• /
• 1999

The effects of Yinjin and Yinjinsaryongsangagambang on a DNA damaging agent, etoposide-induced apoptosis, cell viability, cell cycle progression, and mRNA expression of apoptosis-related genes of human hepatocyte cell line HepG2 were investigated using tryphan blue exclusion assay, MTT assay, flow cytometry, immunocytometric analysis of PCNA, and quantitative RT-PCR analysis. MTT assay showed that Yinjin and Yinjinsaryongsangagambang increases cellular viability of HepG2 cells in a dosage-dependent manner. Stimulation of cell cycle progression by Yinjin or Yinjinsaryongsangagambang was detected by flow cytometric analysis of the DNA content and immunocytometric analysis of PCNA expression. A significant reduction of a DNA-damaging agent, etoposide-induced apoptosis were found in both Yinjin and Yinjinsaryongsangagambang-treated cells in dosage-dependent manner. In overall, 3-fold reduction of apoptosis was recognized in $10.0\;{\mu}g/ml$ of Yinjin or Yinjinsaryongsangagambang-treated cells compared to untreated cells. Although the difference is not significant, Yinjinsaryongsangagambang showed slightly higher effect on the inhibition of apoptosis than Yinjin. From flow cytometric analysis of apoptosis, while 39.9% of untreated cells showed etoposide-induced apoptotic cell death, only 19.6% or 17.4% of Yinjin or Yinjinsaryongsangagambang-treated cells were fond at apoptotic sub G1 phase, respectively. Interestingly, strong induction of Gadd45-mRNA was observed from Yinjin or Yinjinsaryongsangagambang-treated cells. However, no changes in expression levels of p53 and Waf1 were detected, demonstrating that induction of Gadd45 mRNA expression by Yinjin or Yinjinsaryongsangagambang occurs by p53-independent mechanism. Marked mRNA inductions of two apoptosis-inhibiting genes, Bcl-2 and Bcl- XL, were found in both Yinjin or Yinjinsaryongsangagambang-treated HepG2 cells while no changes was detected in expression levels of an apoptosis-promoting gene, Bax.

• Journal of Energy Engineering
• /
• v.22 no.1
• /
• pp.28-37
• /
• 2013

Stirred tank is widely used in various industries for mixing operations and chemical reactions for single- or multi-phase fluid systems. For designing agitator of high performance, quantity data of internal flow characteristics influenced by mixing performance are definitely confirmed but quantity analysis about the transient flow characteristics of complicate structure is recognized as difficult problem in the present. In this study, two models of commercial CFD code Fluent 6.3 used to propose suitable for the tank analysis. Agitation of Stirred tank is analyzed using a mixed model and the flow in the stirred tank is analyzed using a standard k-${\varepsilon}$ model. Multiple reference frame(MRF) and Sliding mesh(SM), the analysis techniques were used For compare a result of CFD with a visualization experiment result, to grasp internal flow and mixing characteristic in stirred tank and to present fundamental analysis method.

• Transactions of the Society of Information Storage Systems
• /
• v.8 no.2
• /
• pp.72-77
• /
• 2012

The demand for the laptop computer has been increased day by day and most of users ask quiet computer and devices to work in comfortable environment. One of the devices which generate acoustic noise is an external ODD. Unlike the internal ODD, the external ODD is easy to emit noise because it runs outside of the computer and also it is packed with a thin plastic covers. As the disk rotates, vortex flow is generated inside of the cavity due to various and complicated mold parts of the cover. In addition, there is a gap between the disk tray and the upper/lower cases, through which the air flows as well as the noise leaks. In this study, we have proposed how to reduce the acoustic noise of an external ODD using numerical and experimental analysis. The pressure fluctuations and turbulent kinetic energy distributions are calculated for the developed model. The results show that the sound pressure level is reduced by 2.3dB through simple modifications of ribs of the top cover, which remove or suppress flow instabilities inside of the cavity.

• Journal of computational fluids engineering
• /
• v.7 no.3
• /
• pp.9-16
• /
• 2002

Most of modem aerospace gas turbines must be operated at a gas temperature which is several hundreds of degrees higher than the melting temperatures of the materials used in their construction. Complicated cooling schemes need to be employed in the combustor walls and in the high pressure turbine stages. Internal passages are cast or machined into the hot sections of aero-gas turbine engines and air from the compressor is used for cooling. In many cases, the cooling system is engineered to utilize jets of high velocity air, which impinge on the internal surfaces of the components. They are categorized as 'Impinging Cooling Method' and 'Vortex Cooling Method'. Specially, research of new cooling system(Vortex Cooling Method) that overcomes inefficiency of film cooling and limitation of space. The focus of new cooling system that improves greatly cooling efficiency using less amount of cooling air on surface heat transfer elevation. Therefore, in this study, a numerical analysis has been peformed for characteristics of flow and heat transfer in the swirl chamber and compared with the flow measurements by LDV. Especially, for understanding high heat transfer efficiency in the vicinity of wall, we considered flow structure, vortex mechanism and heat transfer characteristics with variation of the Reynolds number.

• The Journal of Korean Medicine Ophthalmology and Otolaryngology and Dermatology
• /
• v.28 no.2
• /
• pp.54-65
• /
• 2015

Objective : This Study was conducted in order to develop the Learning Satisfaction (LS)and Learning Flow Scale(LFS) for Korean Medical Ophthalmology & Otolaryngology & Dermatology and to investigate the reliability and validity. Methods : LF and LFS were administered to 44 students and 20 resident physicians . We examined the test-retest reliability, internal consistency and perfomed factor analysis. Result : 1. Test-retest reliability were reliable on LS and LFS for Korean Medical Ophathalmology & Otolaryngology.2. Test-retest reliability were unreliable comparatively on LS and LFS for Korean Medical Dermatology.3. internal consistency were all reliable in LS and LFS Korean Medical Ophthalmology & Otolaryngology & Dermatology.4. factor analysis were reliable only LS of Korean Medical Dermatology. Conclusions : LS and LFS has reliability to measure learning satisfaction and learning flow of Korean Medical students. But there is no evidence about validity of LS and LFS for Korean Medical Ophthalmology & Otolaryngology & Dermatology.