• Journal of Advanced Marine Engineering and Technology
• /
• 제28권7호
• /
• pp.1055-1062
• /
• 2004

As for the Production of internal combustion engines there has been further movement toward development of high Performance engines with improved fuel efficiency as well as a lightweight and a small size. These tendencies help to solve the problems in engines for example, such as thermal load. abnormal combustion and so on. In order to investigate these Problems, a thin film-type probe for measuring instantaneous temperature has been suggested. A method for manufacturing such a probe was established in this study The instantaneous surface temperature of a constant volume combustion chamber was measured by using this probe and the heat flux was obtained through Fourier analysis In order to thoroughly understand the characteristics of combustion. authors measured wall temperature of combustion chamber and calculated heat flux through a cylinder wall while varying the protrusion height of probe. For these Purposes, the instantaneous surface temperature probe was developed. thereby making possible the analysis of instantaneous temperature of wall surface and the detection of unsteady heat flux in the constant volume combustion chamber.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2006년도 제33회 KOSCO SYMPOSIUM 논문집
• /
• pp.36-41
• /
• 2006

A simplified model of plastic layer and internal gas pressure In a coke oven is presented. We calculate internal gas pressure using presented model. And results are compared with calculated results using experimental data. Results show the difference of internal gas pressure by coal composition. The model is used to show that the permeability at the resolidification end of the plastic layer is a key determinant of the magnitude of the internal gas pressure.

• 한국수소및신에너지학회논문집
• /
• 제23권3호
• /
• pp.227-235
• /
• 2012

Finding an alternative fuel and reducing environmental pollution are the main goals for future internal combustion engines. The purpose of this study is to obtain low-emission and high-efficiency by hydrogen enriched LPG fuel in constant volume chamber. An experimental study was carried out to obtain fundamental data for the combustion and emission characteristics of pre-mixed hydrogen and LPG in a constant volume chamber (CVC) with various fractions of hydrogen-LPG blends. To maintain equal heating value of fuel blend, the amount of LPG was decreased as hydrogen was gradually added. Exhaust emissions were measured using a HORIBA exhaust gas analyzer for various fractions of hydrogen-LPG blends. The results showed that the rapid combustion duration was shortened, and the rate of heat release elevated as the hydrogen fraction in the fuel blend was increased. Moreover, the maximum rate of pressure rise also increased. These phenomena were attributed to the burning velocity which increased exponentially with the increased hydrogen fraction in the $H_2$-LPG fuel blend. Exhaust HC and $CO_2$ concentrations decreased, while NOX emission increased with an increase in the hydrogen fraction in the fuel blend. Our results could facilitate the application of hydrogen and LPG as a fuel in the current fossil hydrocarbon-based economy and the strict emission regulations in internal combustion engines.

• 한국추진공학회지
• /
• 제21권1호
• /
• pp.63-71
• /
• 2017

메탄($CH_4$)/산소($O_2$) 액체이원추진제는 친환경성, 무독성, 경제성, 우수한 성능 등의 장점으로 최근 들어 차세대 친환경 이원추진제로서 관심을 받고 있다. 본 연구에서는 연소실 내 압력 변화에 따른 기체 메탄/산소 비예혼합 동축 화염의 연소안정한계를 측정하고, 화염 및 유동의 가시화를 통해 분사 조건 및 압력 변화에 따른 화염의 구조와 특성을 파악하였다. 연구 결과 연료과농 조건에서 연소실 내 압력이 증가할 경우 연소안정한계가 확장되고 반응 영역이 증가하는 것을 확인할 수 있었다.

• 대한기계학회논문집
• /
• 제8권6호
• /
• pp.544-552
• /
• 1984

본 연구에서는 Chiu et al.의 집단연소이론에 대한 비정상집단연소모델(non- steady group combustion model)을 개발, 정지된 액적군에서 초기 액적들의 분포상태, 즉 초기액적들의 크기, 수밀도 및 액적군의 크기에 따른 연소시간, 연소형태 및 특성 과 화염의 성질등을 비정상 상태하에서 이론적인 모델을 통하여 고찰한다.

• Journal of Advanced Marine Engineering and Technology
• /
• 제18권1호
• /
• pp.81-91
• /
• 1994

Combustion noise involved with chemical heat release and turbulent process in turbopropulsion systems, gasturbine, industrial furnaces and internal engines is indeed noisy. The experimental study reported in this paper is made to identify a dominant combustion noise in jet flames. Gaseous propane and kerosene fuel have been used with air as the oxidizer in a different jet combustion systems. Combustion and aerodynamic noise are studied through far field sound pressure measurements in an anechoic chamber. And also mean temperature and velocities and turbulent intensities of both isothermal and reacting flow fields were measured. It is shown that axial mean velocity of reacting flow fields is higher about 1 to 3m/sec than that of cold flow in a gaseous combustor. As the gaseous fuel flow rate increases, the acoustic power increases. But the sound pressure level for the spray flame decreases with increasing equivalence ratio. The influence of temperature in the combustion fields due to chemical heat release has been observed to be a dominant noise source in the spray flame. The spectra of combustion noise in gaseous propane and kerosene jet flame show a predominantly low frequency and a broadband nature as compared with the noise characteristics in an isothermal air jet.

• 한국자동차공학회논문집
• /
• 제5권1호
• /
• pp.27-37
• /
• 1997

Internal combustion engine is the main source of environmental pollutants and therefore better technology is required to reduce harmful elements from the exhaust gases all over the world. Especially, harmful elements from the exhaust gases are caused by incomplete combustion of mixture inside the engine cylinder and this abnormal combustion like misfire or partial burning is the direct cause of the air pollution and engine performance degradation. the object of this research is to detect abnormal combustion like misfire and to keep the engine performance in the optimal operating state. Development of a new system therefore could be applied to a real car. To realize this, the spark-plug in a conventional ignition system is used as a misfire detection sensor and breakdown voltage is analyzed. In this research, bias voltage(about 3kV) was applied to the electrodes of spark-plug and breakdown voltage signal is obtained. This breakdown voltage signal is analyzed and found that a combustion phenomena in engine cylinder has close relationship with harmonic coefficient K which was introduced in this research. Newly developed combustion diagnostic method( breakdown voltage signal analysis) from this research can be used for the combustion diagnostic and combustion control system in an real car.

• 한국추진공학회지
• /
• 제11권5호
• /
• pp.31-36
• /
• 2007

연소 압력이 70 bar인 고압 축소형 연소기의 연소성능 특성을 알아보았다. 모든 연소시험은 하드웨어의 손상 없이 성공적으로 이루어졌다. 분사기의 혼합특성과 분사기 배열이 연소성능에 큰 영향을 미치는 요소임을 파악하였다. 연소기의 특성속도는 외부 혼합보다 내부 혼합 분사기에서 더 크게 나타났으며 단위분사기당 추진제의 유량이 감소함에 따라 특성속도도 증가하였다. 추진제 매니폴드 및 연소실에서 측정된 압력 섭동은 평균 연소압력의 3% 이하로 연소안정성 기준치 보다 낮은 값을 보여 안정적인 연소기임을 보였다.

• 열처리공학회지
• /
• 제16권4호
• /
• pp.216-223
• /
• 2003

In the production of internal combustion engines, there have been trends to develop the high performance engines with improved fuel efficiency, lighter weights and smaller sizes. This trends help to answer problems related to thermal load and abnormal combustion, etc. in these engines. In order to investigate these problems, a thin film-type probe and its manufacturing method for instantaneously measuring surface-temperatures have been proposed in this study, Instantaneous surface temperature of a constant volume combustion chamber was measured by this probe and heat flux was obtained by Fourier analysis. In order to thoroughly understand the characteristics of combustion, the authors measured the wall temperature of the combustion chamber and computed heat flux through a cylinder wall while varying the protrusion height of the probe have been measured. To achieve the above goals, a instantaneous temperature probe was developed, thereby making possible the analysis of the instantaneous temperature of wall surface and the detection of unsteady heat flux in the constant volume combustion chamber.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 2014년도 제49회 KOSCO SYMPOSIUM 초록집
• /
• pp.339-342
• /
• 2014

Rotary kiln produces lime from limestone through thermal decomposition. Ring formation in kiln internal wall is known issue that decreases productivity. The cause of ring formation is temperature imbalance as flame leans toward upper wall. Therefore, burner nozzle geometry was changed to improve air-fuel mixing state which leads to prevention of ring formation. CFD simulation and experimental test were performed in this study to investigate the effect of air-fuel mixing on flame structure, temperature and $NO_X$ concentration. It is shown that combustion efficiency has been enhanced and $NO_X$ concentration has been decreased by using swirl flow for secondary combustion air. It's also shown that flame has been straightened by using straight flow for secondary combustion air.