• 동력기계공학회지
• /
• 제11권2호
• /
• pp.64-71
• /
• 2007

The main purpose of this study is to analyze the characteristics of toluene removal by plasma, photocatalyst, and plasma/photocatalyst system with the major parameters such as flow rate, inlet toluene concentration and applied voltage, etc., experimentally. In the combined plasma/photocatalyst process, rates of toluene conversion are represented as 99% at flow rate 250, 500 mL/min while, below 97% at flow rate 1000 mL/min due to the low residence time(reaction time) at the same applied voltage 4173 voltage and toluene inlet concentration 50 ppm. The intermediate products are detected by GC/MS analysis showing the small amounts of benzoic acid, benzyl alcohol and residual ozone concentration $0.04{\sim}0.05$ ppm generated by plasma process in the present system.

• 기술사
• /
• 제18권2호
• /
• pp.1-5
• /
• 1985

In the flood prediction research, it is pointed out that the difficulty of flood prediction is the frequently experienced overestimation of flood peak. That is caused by the rainfall prediction difficulty and the nonlinearity of hydrological phenomena. Even though the former reason will remain still unsolved, but the latter one can be possibly resolved the method of the AMRA (Auto Regressive Moving Average) model for each runoff component as developed by Dr. Hino and Dr. Hasebe. The principle of the method consists of separating though the numerical filters the total runoff time series into long-term, intermediate and short-term components, or ground water flow, interflow, and surface flow components. As a total system, a hydrological system is a non-linear one. However, once it is separated into two or three subsystems, each subsystem may be treated as a linear system. Also the rainfall components into each subsystem a estimated inversely from the runoff component which is separated from the observed flood. That is why flood prediction can be done without rainfall data. In the prediction of surface flow, the Kalman filter will be applicable but this paper shows only impulse function method.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집B
• /
• pp.386-391
• /
• 2001

In this paper, the vibration characteristics of IHTS(Intermediate Heat Transfer System) piping system of LMR(Liquid Metal Reactor) conveying hot liquid sodium are investigated to eliminate the pipe supports for economic reasons. To do this, a 3-dimensional straight pipe element and a curved pipe element conveying fluid are formulated using the dynamic stiffness method of the wave approach and coded to be applied to any complex piping system. Using this method, the dynamic characteristics including the natural frequency, the frequency response functions, and the dynamic instability due to the pipe internal flow velocity are analyzed. As one of the design parameters, the vibration energy flow is also analyzed to investigate the disturbance transmission paths for the resonant excitation and the non-resonant excitations.

• 설비공학논문집
• /
• 제24권2호
• /
• pp.111-120
• /
• 2012

In this study, to present the data in the internal thermal condition of Double skin facade were measured internal temperature and inlet and outlet openings wind speed of double skin facade. Measurements were similar to temperatures in the upper double skin facade. Especially in summer, temperature stratification is through to be unfulfilled seamlessly despite inlet and outlet openings open. Double skin facade inlet and outlet openings of the air flow rate was slower outlet openings of the air flow rate than inlet openings of the air flow rate.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.373-378
• /
• 2003

It is important that overheat protection of super heated tube in boiler operation and maintenance. The overheat of super heat tube can make damage and rupture of tube material, which causes accidental shutdown of boiler. The super heated tube overheat is almost due to the lack of uniformity of gas temperature distribution. There are two ways to protect overheat of super heated tube. The one is to control hot gas operation pattern which is temperature or flow distribution. the other is to control super heated steam flow distribution. The former is difficult than the later, because of control device design. In this paper steam flow control method which uses orifices is proposed to protect overheat of super heat tube.

• 대한조선학회논문집
• /
• 제34권1호
• /
• pp.41-49
• /
• 1997

작은 파 기울기(Ak=0.01)를 갖는 Stokes 파/평판의 경계층 및 반류에 대하여 엄밀 및 근사 자유표변 경계조건을 적용하여 Navier-Stokes 식을 수치해석하였다. 거시유동에서는 외부 흐름 압력 변화가 유선방향의 속도 성분을 가속 혹은 감속시키며 교차 유동의 방향 변화를 야기시킨다. 특히 반류는 역(逆)압력기울기 영역에서보다 순(順)압력기울기 영역에서 그 반응이 크며 정수 중에서의 값을 평균치로 하지 않고 편향되는 반류 편향 특성을 갖는다. 미시유동에서는 자유표면 경계조건이 경계층 및 근접/중간 반류영역에서 큰 영향을 미친다. 차수크기 추정은 계산 결과와 잘 일치하였으며 근사 자유표변 경계조건은 상당한 오차를 유발시킴을 알 수 있다.

• Membrane and Water Treatment
• /
• 제12권1호
• /
• pp.37-41
• /
• 2021

This paper presents the multiscale calculation results of the very fast volume transport in micro/nano cylindrical tubes with the wall slippage. There simultaneously occurs the adsorbed layer flow and the intermediate continuum fluid flow which are respectively on different scales. The modeled fluid is water and the tube wall is somewhat hydrophobic. The calculation shows that the power loss on the tube no more than 1.0 Watt/m can generate the wall slippage even if the fluid-tube wall interfacial shear strength is 1 MPa; The power loss on the scale 104 Watt/m produces the volume flow rate through the tube more than one hundred times higher than the classical hydrodynamic theory calculation even if the fluid-tube wall interfacial shear strength is 1 MPa. When the wall slippage occurs, the volume flow rate through the tube is in direct proportion to the power loss on the tube but in inverse proportion to the fluid-tube wall interfacial shear strength. For low interfacial shear strengths such as no more than 1 kPa, the transport in the tube appears very fast with the magnitude more than 4 orders higher than the classical calculation if the power loss on the tube is on the scale 104 Watt/m.

• 대한화학회지
• /
• 제58권6호
• /
• pp.560-568
• /
• 2014

단백질 폴딩 반응에서 정전기적 상호작용의 역할을 라이신 29를 알라닌으로 치환한 변이 유비퀴틴을 사용하여 탐색하였다. 유비퀴틴의 입체구조에서 라이신 29의 곁사슬은 글루탐산 16과 아스파르산 21의 곁사슬과 근접한 거리에 있어서 곁사슬끼리 정전기적 상호작용을 통하여서 삼차원 입체구조를 안정화시킬 것으로 예측되었다. 라이신을 알라닌으로 치환하여 정전기적 상호작용을 제거하였을 때 유비퀴틴의 native state의 구조적 안정성이 ~20% 감소한 점은 라이신 29에 의한 정전기적 상호작용이 단백질 삼차구조의 안정성에 상당히 기여하고 있다는 점을 시사하였다. 폴딩 반응의 진행 과정을 stopped-flow 장치로 측정한 folding kinetics 실험은 이전에 관찰된 것과 마찬가지로 unfolded state에서 native state로 진행하는 과정에 중간단계를 거치는 three-state on-pathway 메커니즘을 따르는 것으로 나타났다. 더욱이 라이신 29에 의한 정전기적 상호작용이 중간단계의 구조적 안정성에 기여하는 정도가 native state의 구조적 안정성에 기여하는 정도의 ~55%인 것으로 나타났다. 이는 유비퀴틴 폴딩의 중간단계의 구조도 라이신 29에 의한 정전기적 상호작용에 의하여 상당히 안정화 된다는 것을 의미하며 따라서 정전기적 상호작용이 단백질 삼차원 입체구조의 골격이 완성된 폴딩의 마지막 단계에 형성되어 단백질 native state의 안정성에만 기여하는 것이 아니라 중간단계가 형성되는 폴딩 반응의 초기에도 형성되어 폴딩 반응을 이끌어가는데도 기여한다는 것을 의미한다.

• 대한기계학회논문집B
• /
• 제38권11호
• /
• pp.881-887
• /
• 2014

본 연구에서는 micro-gap 판형 열교환기 내부의 열유동 특성에 대한 수치해석을 수행하였다. 특히 유량 조건에 따라 열교환기의 주 채널로부터 각 micro-gap 으로의 유동분배에 대한 유동관성의 영향에 대하여 조사하였다. 열교환기 주 채널의 유동을 레이놀즈 수 100 부터 10000 까지 변화시키며 그에 따른 각 micro-gap 으로의 유동분배와 온도분포의 불균일 정도를 평가하였다. 수치해석 결과 유동분배는 유동관성에 의해 크게 영향을 받는 것으로 나타났으며, 관성 효과를 감소시킬 수 있는 헤더 설계를 통해 유동분배 불균일 정도를 줄일 수 있었다. 또한 micro-gap 을 통과한 유체의 온도분포의 불균일 정도는 주유량이 증가함에 따라 증가 후 감소 추세를 나타냈다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 추계종합학술대회 논문집(1)
• /
• pp.21-24
• /
• 2000

End-to-end congestion control mechanism have been critical to the robustness and stability of the Internet. Most of today's Internet traffic is TCP, and we expect this to remain so in the future. TCP/IP is the intermediate transport layer candidate for today's applications. TCP uses an adaptive window-based flow control. The congestion avoidance and control algorithms deployed by TCP aims at using the available network bandwidth. This paper compares different congestion control policies, and proposes the new design mechanism for future public networks