• Membrane and Water Treatment
• /
• v.1 no.4
• /
• pp.297-316
• /
• 2010

Membrane fouling is one of the major operational concerns of membrane processes which results in loss of productivity. This paper investigates the ultrafiltration (UF) results of synthetic oil-in-water (o/w) emulsion using flat sheets of polysulfone (PSf) membrane synthesized with four different compositions. The aim is to identify the mechanisms responsible for the observed permeate flux reduction with time for different PSf membranes. The experiments were carried out at four transmembrane pressures i.e., 68.9 kPa, 103.4 kPa, 137.9 kPa and 172.4 kPa. Three initial oil concentrations i.e., 75 $mgL^{-1}$, 100 $mgL^{-1}$ and 200 $mgL^{-1}$ were considered. The resistance-in-series (RIS) model was applied to interpret the data and on that basis, the individual resistances were evaluated. The significances of these resistances were studied in relation to parameters, namely, transmembrane pressure and initial oil concentration. The total resistance to permeate flow is found to increase with increase in both transmembrane pressure and initial oil concentration while for higher oil concentration, resistance due to concentration polarization is found to be the prevailing resistance. The applicability of the constant pressure filtration models to the experimental data was also tested to explain the blocking process. The study shows that intermediate pore blocking is the dominant mechanism at the initial period of UF while in the later period, the fouling process is found to approach cake filtration like mechanism. However, the duration of pore blocking mechanism is different for different membranes depending on their morphological and permeation properties.

• Korean Chemical Engineering Research
• /
• v.57 no.1
• /
• pp.28-41
• /
• 2019

We carried out performance analysis of Sodium-Water Reaction Pressure Relief System of Prototype Generation-IV Sodium-Cooled Fast Reactor. We analyzed transient-dynamic behavior of fluids inside the steam generator to vent into a sodium dump tank or a water dump tank when tubes in the steam generator were broken to cause a large-water-leak accident. Accordingly, we preliminarily evaluated design requirements of our system. Our results showed that sodium in the shell side of the steam generator and in Intermediate Heat Transport System was completely vented within 50 s and feed water in the tube side of the steam generator was completely vented within 2.5 s. It was analyzed that pressure of the tube side of the steam generator was higher than pressure of the shell side of the steam generator, which showed that sodium in the shell side did not flow into the tube side. Our results are expected to be used as basis information to performance analysis of Sodium-Water Reaction Pressure Relief System of Prototype Generation-IV Sodium-Cooled Fast Reactor.

• Journal of Coastal Disaster Prevention
• /
• v.5 no.4
• /
• pp.183-192
• /
• 2018

In recent years, coastal areas have been suffering from coastal erosion, such as destruction of coastal roads and military facilities. In this study, the Delft3D model was used to analyze the sediment transport pattern due to seasonal characteristics of summer and winter waves in Anmok beach of the East coast. Typhoon and high waves are mainly are coming from ENE direction in the summer season and the flows occur in the northward. In winter, high waves are incident from NE and the flows occur in the southward. These seasonal patterns were simulated by using Delft3D model. As for model input, reanalysis wave data of the past 38 years were used, and the seasonal patterns were analyzed by dividing the whole year into summer and winter season. The grid point of the 38 year reanalysis data is far from the Anmok beach, so the three model grid systems (wide grid -> intermediate grid -> detailed grid) are constructed. Most of the flows in the NW direction occurred in summer, but erosion and deposition was alternated along the coastline. In winter, sediment was deposited near Gangnung Port due to the southern flow and the southern port. Strong winter waves compared to summer tend to cause deposition around Gangnung Port throughout the year.

• Journal of Korea Trade
• /
• v.23 no.7
• /
• pp.96-112
• /
• 2019

Purpose - "Trade Facilitation" aims the easier flow of trade across borders, driven not only by effective customs administration, the efficiency of appropriate authorities, but also by telecommunications, the quality of infrastructures and competent logistics. Facilitating trade will help lower trade development costs as well as improve economic development and enhance economic benefits for emerging economies at a time when imports and exports are sent in and out across borders several times in the form of intermediate and final products. Not only that, globalization is being accelerated, which in turn increases competitiveness and this makes logistics one of the key factors when it comes to international trade. Highly efficient logistics services promote product movement, ensure product safety and delivery speed, and reduce trade costs between countries. The purpose of this study is, by using the LPI indices based on gravity model estimates, to analyze the impact of each LPI component on trade with the 20 biggest exporting countries of Northeast Asian countries-Korea, Japan, and China-which account for 19.05% of global exports. Design/methodology - Also, this study statistically analyzes the impact of trade on Northeast Asian countries' top 20 exporting countries, using the LPI indices relevant to Trade Facilitation based on the gravity model estimates. Findings - As a result, it was turned out that the distance, GDP, and the LPI components have relevant impact on the trade exports of all three countries but demonstrated little relation to the demographic perspective. Originality/value - The study also found we can increase the trade volume by improving three countries' trade partners' LPI indices since Korea, Japan, and China share most of their 20 biggest trade partners.

• Korean Journal of Veterinary Service
• /
• v.45 no.3
• /
• pp.243-248
• /
• 2022

The HPLC conditions for analysis of ivermectin in solutions dosage forms of commercial anthelmintics are different for each product. The purpose of this study was to establish a standardized chromatographic method for the quantification of ivermectin in solution. The separation was achieved on Waters Xbridge C18 column (4.6×150 nm, 5 ㎛) using different kinds of mobile phase composed of water/methanol/acetonitrile (15/34/51, v/v and 19.5/27.5/53, v/v), with UV detection at wavelengths 245 nm and 254 nm. A total of five commercial ivermectin in solution samples were analyzed. In this study, the optimal chromatographic conditions for analysis of ivermectin in solution were mobile phase of water/methanol/acetonitrile (15/34/51, v/v) at a flow rate of 1.0 mL/min and a detection wavelength of 245 nm using a Waters Xbridge C18 column (4.6×250 nm, 5 ㎛) at a column temperature of 25℃. The linearity was observed in the concentration range of 50~150 ㎍/mL, with a correlation coefficient, r²= 0.99999. The limit of detection and the limit of quantification were 0.88 and 2.68 ㎍/mL, respectively. The accuracy (% recovery) was found to be 98.9 to 100.3%. Intra-day and Intermediate precisions with relative standard deviations were less than 1.0%. The content of ivermectin for five market samples ranged 91.2~102.7%. The proposed method was also found to be robust, therefore, the method can be used for the routine analysis of ivermectin in solutions dosage forms.

• Nuclear Engineering and Technology
• /
• v.55 no.1
• /
• pp.71-79
• /
• 2023

Air ingress incidents are major safety accidents in very-high-temperature reactors (VHTRs). Air containing a high volume fraction of oxygen may cause severe oxidation of core components at the VHTR, especially for the significantly thin alloy tube wall in the intermediate heat exchanger (IHE). The research objects of this study are Inconel 617 and Incoloy 800H, two candidate alloys for IHE in VHTR. The air ingress accident scenario is simulated with high-temperature air flow at 950 ℃. A continuous oxide scale was formed on the surfaces of both the alloys after the experiment. Because the oxide scale of Inconel 617 has a loose structure, whereas that of Incoloy 800H is denser, Inconel 617 exhibited significantly more severe internal oxidation than Incoloy 800H. Further, Inconel 617 showed a significant decrease in ultimate tensile strength and plasticity after aging for 200 h, whereas Incoloy 800H maintained its tensile properties satisfactorily. Through control experiment under vacuum, we preliminarily concluded that serious internal oxidation is the primary reason for the decline in the tensile properties of Inconel 617.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.26 no.1B
• /
• pp.15-25
• /
• 2006

Using kinematic wave equation, the influence of moving storms to runoff was analysised with a focus on watersheds. Watershed shapes used are the oblong, square and elongated shape, and the distribution types of moving storms used are uniform, advanced and intermediate type. The runoff hydrographs according to the rainfall distribution types were simulated and the characteristics were explored for the storms moving down, up and cross the watershed with various velocity. The shape, peak time and peak runoff of a runoff hydrograph are significantly influenced by spatial and temporal variability in rainfall and watershed shapes. A rain storm moving in the cross direction of channel flow produces a higher peak runoff than in the downstream direction and upstream direction. A peak runoff from a storm moving downstream exceeds that from a storm moving upstream. For storms moving downstream peak time was more delayed than for other storm direction in the case of elongated watershed. The runoff volume and time base of the hydrograph decreased with the increasing storm speed.

• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.17 no.1
• /
• pp.38-46
• /
• 2024

In general, EEG signal analysis has been the subject of several studies due to its ability to provide an objective mode of recording brain stimulation, which is widely used in brain-computer interface research with applications in medical diagnosis and rehabilitation engineering. In this study, we developed EEG reception hardware to measure electroencephalograms and implemented a processing system, classifying it into server and data processing. It was conducted as an intermediate-stage research on the implementation of a brain-computer interface using electroencephalograms, and was implemented in the form of predicting the user's arm movements according to measured electroencephalogram data. Electroencephalogram measurements were performed using input from four electrodes through an analog-to-digital converter. After sending this to the server through a communication process, we designed and implemented a system flow in which the server classifies the electroencephalogram input using a convolutional neural network model and displays the results on the user terminal.

• Journal of the Korean Institute of Gas
• /
• v.21 no.5
• /
• pp.16-26
• /
• 2017

In chemical industry plants, the raw material, intermediate and final products can leak from unstable joints of flanges and valves as well as cracks of storage tanks. From the safety and economic standpoints, it is very important to understand whether leaks or not and leakage rate. The OGI(optical gas image) technique can tell gas leakages, but cannot give the leakage rate. Some special OGI devices can show the kind of gas in different color concentration in different darkness. Therefore the research on quantification of OGI is necessary. In this research, we have developed the practical method to quantify OGI of methane leakage. To estimate 3-dimensional gas leakages distribution from 2-dimensional OGI, the Monte Carlo Probability technique was applied. First the number of points in the area of width(2.54 cm) and length(2.54 cm) in OGI was counted. Total no of each experiment was compared with the measured flow rate. The correlation average between total points and measured flow rate was found to be 0.980. Reversely we estimated the leakage rate of OGI by use of the correlation table. The results showed good agreement between the estimation value and the measured value.

• Journal of Korea Water Resources Association
• /
• v.39 no.7 s.168
• /
• pp.605-615
• /
• 2006

In order to analyze movement of soil moisture, Time Domain Reflectometry(TDR) with multiplex system has been installed at the Bumreunsa hillslope of Sulmachun Watershed to configure spatial-temporal variation pattern considering seasonal characteristic. An intensive surveying was performed to build a refined digital elevation model(DEM) and flow determination algorithms with inverse surveying have been applied to establish an efficient soil moisture monitoring system. Soil moisture data were collected through an intensive and long term monitoring 380 hrs in November of 2003 and 1037 hrs in May and June of 2004. Soil moisture data shows corresponding variation characteristics of soil moisture on the up slope, buffer, main channel zones of the hillslope which were classified from terrain analysis. Measured soil moisture data were discussed in conjunction with flow characteristic through terrain analysis. Regardless season, immediate responses of soil moisture about rainfall looks similar but recession and recharge are primary characteristics of intermediate soil moisture variation for spring to summer and fall to winter season, respectively.