• The Korean Journal of Ecology
• /
• v.13 no.4
• /
• pp.321-329
• /
• 1990

An investigation was performed to elucidate wave character of the timber line on the middle slope of the west side of Paektusan. The Betula ermanii forest, which composes the timber line on about 2, 060m elevation of sea level, is the pure community of B. ermanii. Diffraction pattern of wave distribution of B. eramnii due to boundary condition of alpine temperature gradient was found out on the timber line. Interference patterns of waves of B. ermanii communities produced by environment conditions such as soil layers, whids, snow and relief were shown on a specific area. These facts indicate that the B. ermanii individuals have wave and particle duality, the complementarity principle.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.723-726
• /
• 2002

This paper describes the design, fabrication, and measurement of a sequential-rotation microstrip-array antenna for the Electronic Toll Collection System (ETCS). The ETCS is made possible by using roadside equipment with radiation pattern that can accurately pinpoint the designated communication area, without interference from other lanes. The sequential-rotation microstrip-array antenna was applied to the absorber to reduce the side lobe level (SLL). Results showed that the antenna yields a return loss at a center frequency of -20.675 dB, an axial ratio of 1.15 dB, and a gain of 20.26 dBi.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.1354-1357
• /
• 2002

In this paper, we propose a suboptimal receiver combining adaptive array antenna and orthogonal decision-feedback detector in DS/CDMA system. Adaptive array antenna can cancel out undesired signal using beamforming scheme. However, if there are interfering signals from undesired users with the same incident angle as that of a desired user, an adaptive array antenna cannot suppress them. The proposed receiver can cancel out remaining interference from users having nearly the same beam pattern. And we employ Orthogonal Decision-Feedback Detector (ODFD) as multiuser detection. The ODFD performs as good as the decorrelating decision -feedback detector (DDD) with much less complexity. Simulation results show that the proposed system provides a significantly enhanced performance.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.59-62
• /
• 2000

As the density of memories increases, unwanted interference between cells and coupling noise between bit-lines are increased and testing high density memories for a high degree of fault coverage can require either a relatively large number of test vectors or a significant amount of additional test circuitry. From now on, conventional test algorithms have focused on faults between neighborhood cells, not neighborhood bit-lines. In this paper, a new algorithm for NPSFs, and neighborhood bit-line sensitive faults (NBLSFs) based on the NPSFs are proposed. Instead of the conventional five-cell and nine-cell physical neighborhood layouts to test memory cells, a three-cell layout which is minimum size for NBLSFs detection is used. To consider faults by maximum coupling noise by neighborhood bit-lines, we added refresh operation after write operation in the test procedure(i.e., write \longrightarrow refresh \longrightarrow read). Also, we present properties of the algorithm, such as its capability to detect stuck-at faults, transition faults, conventional pattern sensitive faults, and neighborhood bit-line sensitive faults.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.11
• /
• pp.2723-2729
• /
• 1993

Moire principles are applied to the measurement of the spindle radial error motion. As opposed to conventional techniques, no master cylinder or ball is needed in the measurement so that the offset and out-of-roundness errors of the master can be inherently eliminated. Two periodic circular gratings are used, one is made on the spindle and the other is held stationary on the reference frame. When the two gratings are seen superimposed during spindle rotation, an interference fringe pattern is observed from which the information on the eccentricity between the two gratings can be extracted with high precision. The optical design and fringe analysis techniques of a prototype measurement system are described in detail with exemplary measurement results.

• The korean journal of orthodontics
• /
• v.16 no.2
• /
• pp.31-41
• /
• 1986

The purpose of this study is to examine the initial reaction of craniofacial complex to the traction of headgears which are frequent used in dinical practice by using holographic interference method. Changes in the fringe pattern according to the traction conditions (outer bow length, load amount, direction) were compared. Human dry skull was used as experimental material, the results were as follows. 1. The density of fringes increased with an increase in load. 2. Maxillary headgear affected circummaxillary bones-temporal bone, zygomatic bone, nasal bone, frontal bone, sphenoid bone as well as maxilla. 3. The most upward-backward displacement was observed in a high pull head gear $(30^{\circ})$, this is though to be a optimal direction for supressing the growth of the maxilla.

• Proceedings of the KSME Conference
• /
• 2003.11a
• /
• pp.950-955
• /
• 2003

The fluid propulsion mechanism of two oscillating flat plates is studied numerically using a discrete vortex method. Presently, the flat plates are assumed to be rigid. To analyze the closely coupled aerodynamic interference between the flat plates, a core addition scheme and a vortex core model are combined together. A calculated wake pattern for a flat plate in heaving oscillation motion is compared with the flow visualization. The effect of wake shapes on the aerodynamic characteristics of the flat plate in pitching oscillation is investigated. The velocity profiles behind the flat plates in pitching oscillations are plotted to investigate the possible thrust generation mechanism.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.414-417
• /
• 2002

This paper describes the possibility of analyzing gait pattern from the variation of the lower leg electrical impedance. This impedance is measured by the four-electrode method. Two current electrodes are applied to the thigh and foot., and two potential electrodes are applied to the lateral aspect, medial aspect, and posterior position of lower leg. We found the optimal electrode position for knee and ankle joint movements based on high correlation coefficient, least interference, and maximum magnitude of impedance change. From such features of the lower leg impedance, it has been made clear that different movement patterns exhibit different impedance patterns and impedance level.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.5A
• /
• pp.688-695
• /
• 2000

We present a multi-view autostereoscopic display system based on volume holographic storage technique. In this proposed system, the interference pattern of spatial multiplexed plane reference and angular multiplexed plane object beams are recorded into a photorefractive crystal, which plays a role of guiding object beams of multi-view images into the desired persfective directions. For reconstruction, object beams containing the desired multi-view image information, which satisfy Bragg matching condition, are illuminated in the time-division multiplexed manner onto the crystal. Then multiple stereoscopic images are Projected to the display plane for autostereoscopic 3D viewing.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.128-131
• /
• 2002

Three Dimensional measuring system using optical interference is greatly needed for semiconductor surface or optical surface. The application of this system are : MEMS product, semiconductor surfaces, optical components, precise machined surface, etc. In this paper, Interferometry based measurement system is introduced, which is nondestructive and noncontact inspection system. This system have relatively many advantage, compared with AFM/STM, SEM, Stylus, etc. The developed system can measure the surface topography with high precision and resolution, and with few seconds. And the associated software algorithm is also developed for the ultra precision 3D measuring surface. Various samples that is measured using this system is showed in the latter of this paper.