• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2014년도 전력전자학술대회 논문집
• /
• pp.213-214
• /
• 2014

This paper compares two instantaneous reactive power definitions in DFIG wind turbine with a back-to-back three-level neutral-point clamped voltage source converter under unbalanced grid conditions. In general, conventional definition of instantaneous reactive power is obtained by taking an imaginary component of complex power. The other definition of instantaneous reactive power can be developed based on a set of voltages lagging the grid input voltages by 90 degree. A complex quantity referred as a quadrature complex power is defined. Proposed definition of instantaneous reactive power is derived by taking a real component of quadrature complex power. The characteristics of two instantaneous reactive power definitions are compared using the ripple-free stator active power control algorithm in DFIG. Instantaneous reactive power definition based on quadrature complex power has a simpler current reference calculation control block. Ripple of instantaneous active and reactive power has the same magnitude unlike in conventional definition under grid unbalance. Comparison results of two instantaneous reactive power definitions are verified through simulation.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1994년도 가을 학술발표회 논문집
• /
• pp.145-151
• /
• 1994

Welded connections have been designed on basis of allowable stresses, wherein the response to loading is assumed to be totally elastic. This is the vector analysis method, which resolves the stresses determined from the direct stress formula and the torsion formula into a vector combination to obtain a solution. It has been known that this method gives conservative answers and typically a very high factor of safety. An analytical method based on the Instantaneous Center of Rotation has been developed which predicts the ultimate strength of an eccentically loaded fillet welded connection. The method of Instantaneous Center of Rotation results in weld resistance capacities greater than the vector analysis method, by recognizing the variation in fillet weld strength with respect to the direction of the applied loading and actual load-deformation response of elemental fillet welds. The procedure of numerical analysis is iterative and complex. The relations between vector analysis method and the method of Instantaneous Center of Rotation on eccentrical distance subjected to variation of load direction are presented in this paper. Considering of the effects on configuration of weld groups, the method of Instantaneous Center of Rotation are provided a more exact results of the numerical analysis.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.92-98
• /
• 2006

In this paper, a planar car model with 3 degrees of freedom was analyzed using the concept of the roll center. To avoid ambiguity, force components which require experimental data were excluded. Only kinematic approach was used to find the position and orientation of the vehicle body and the position of the roll center. The roll center was found by the pole with infinitesimal movement and Kennedy-Aronhold theorem. Centrodes, which are the loci of instantaneous centers of planar motion, were constructed with analyzed results to show characteristics of vehicle body motion. To verify the presented analysis method in this paper, the locus of the roll center and the motion of a 3 D.O.F. planar car model were compared with those of the 1 D.O.F. model.

• Journal of Electrical Engineering and Technology
• /
• 제1권3호
• /
• pp.279-286
• /
• 2006

A method for estimating the instantaneous phasor of a fault current signal is proposed for high-speed distance protection that is immune to a DC-offset. The method uses a modified notch filter in order to eliminate the power frequency component from the fault current signal. Since the output of the modified notch filter is the delayed DC-offset, delay compensation results in the same waveform as the original DC-offset. Subtracting the obtained DC-offset from the fault current signal yields a sinusoidal waveform, which becomes the real part of the instantaneous phasor. The imaginary part of the instantaneous phasor is based on the first difference of the fault current signal. Since a DC-offset also appears in the first difference, the DC-offset is removed trom the first difference using the results of the delay compensation. The performance of the proposed method was evaluated for a-phase to ground faults on a 345kV 100km overhead transmission line. The Electromagnetic Transient Program was utilized to generate fault current signals for different fault locations and fault inception angles. The performance evaluation showed that the proposed method can estimate the instantaneous phasor of a fault current signal with high speed and high accuracy.

• 한국운동역학회지
• /
• 제19권4호
• /
• pp.779-791
• /
• 2009

본 연구의 목적은 원위지점에서 움직이는 실험 데이터를 이용하여 그 점들의 회전운동 순간 중심점을 분석하는 프로그램(Centering 1.0)을 개발하는 것이다. 이를 위해 수학적인 알고리즘을 정의하고, 물체의 운동에 대한 실험 데이터를 입력하여 회전운동 순간 중심점을 찾아내는 컴퓨터 프로그램을 구현하였다. 프로그램을 검증하기 위한 실험 데이터는 한명의 숙련된 여성골퍼의 피칭(40m 캐리)과 퍼팅(4m) 스트로크 시 클럽의 움직임으로 수집하였다. 그리고 이 데이터를 본 연구를 통해 개발된 회전운동 순간 중심점 분석 프로그램에 적용하여 클럽의 움직임 시 회전의 중심점을 찾고, 그 위치의 크기를 반지름으로 나타내었다. Centering 1.0 프로그램은 구간을 크게 정의할 때 반지름의 오차가 약간 있었으나, 구간을 작게 나눌수록 매우 근사치의 값을 제시하여주었다. 피칭과 퍼팅을 비교할 경우에 피칭의 반지름이 퍼팅보다 매우 작게 나타났으며, 퍼팅의 경우 중심의 위치는 인체 내에 있지 않고 최고 3m 외부에 위치하는 것으로 나타났다. Centering 1.0 프로그램은 회전운동에서 구한 데이터의 최소 3개만 입력하면 반지름 값을 알 수 있으며, 이것이 누적되면 회전운동 순간 중심점의 이동경로를 알 수 있다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 하계학술대회 논문집 B
• /
• pp.970-972
• /
• 2003

This paper presents a new speed sensorless control method of a permanent magnet synchronous motor based on instantaneous reactive power. The proposed algorithm is constructed by instantaneous reactive power in a synchronously rotating reference frame and is not affected by mechanical motor parameters, because mechanical equation is not used. The effectiveness of the proposed system is confirmed by the experimental results.

• 한국가스학회지
• /
• 제15권3호
• /
• pp.26-30
• /
• 2011

개방형 순간 가스온수기는 설치와 관리가 적절히 되지 않아 일산화탄소 중독과 질식과 같은 인명사고를 발생시킬 수 있다. 연소기에 공기가 충분히 공급되지 않거나 배기구가 막히면 배기가스 중의 일산화탄소(CO)의 농도가 증가하는 특성을 보인다. 본 연구는 가정집에서 사용 중인 개방형 가스온수기를 회수하여 연소기 주변 공기 중산소농도 및 배기가스 중 CO농도의 변화를 확인하였다. 환기구 면적에 따른 산소농도 측정 실험에서 환기구의 면적이 바닥면적의 3.5%에서 산소농도가 약 17.7%로 나타났고, 배기구를 폐쇄한 상태에서 CO농도를 측정한 결과 4,000ppm이상이 측정되었다. 따라서 정기적으로 배기구를 점검하는 것이 환기구 크기보다 일산화탄소 중독사고를 예방하기 위하여 중요하다.

• Journal of Electrical Engineering and Technology
• /
• 제6권4호
• /
• pp.466-473
• /
• 2011

This paper proposes a protection algorithm for a wind turbine generator (WTG) in a large wind farm. To minimize the outage section, a protection relay for a WTG should operate instantaneously for an internal fault or a connected feeder fault, whereas the relay should not operate for an internal fault of another WTG connected to the same feeder or an adjacent feeder fault. In addition, the relay should operate with a delay for an inter-tie fault or a grid fault. An internal fault of another WTG connected to the same feeder or an adjacent feeder fault, where the relay should not operate, is determined based on the magnitude of the positive sequence current. To differentiate an internal fault or a connected feeder fault from an inter-tie fault or a grid fault, the phase angle of the negative sequence current is used to distinguish a fault type. The magnitude of the positive sequence current is then used to decide either instantaneous operation or delayed operation. The performance of the proposed algorithm is verified under various fault conditions with EMTP-RV generated data. The results indicate that the algorithm can successfully distinguish instantaneous operation, delayed operation, or non-operation depending on fault positions and types.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.442-447
• /
• 2003

The characteristics of instantaneous wall-surface temperature of impinging plate in case of ultra high pressure injection have been measured and analyzed by using thin film instantaneous temperature probe and ultra high pressure injection equipment. The decreasing rate of temperature was greater in case of higher temperature of impinging plate. Temperature drop was largest at center of piston and it was slight for others. Instantaneous temperature decreases rapidly with increasing injection pressure. But above 2,500bar of injection pressure, the decreasing rates are slightly affected by increasing injection pressure.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1991년도 하계학술대회 논문집
• /
• pp.627-630
• /
• 1991

This study is about vector controlled inverter for high quality elevator drive that is to improve the settling accuracy of elevator car and passenger's comfort in commercial buildings. In this study, an instantaneous space vector control type inverter was used to reduce the torque ripple ant to improve the velocity follow-up. This method calculates Instantaneous actual output torque and flux of induction motor by voltage and current, then compares them with a reference values by a speed regulator. The outputs of comparators select a switching mode, for an optimal voltage vector. Also, this study used IGBT (Insulated Gate Bipolar-Transistor), a high speed switching element, to reduce sound noise level, and DSP (Digital Signal Processor) was used to improve the reliability of the control circuit by fully digitalization.