• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.744_745
• /
• 2009

고해상도의 NMR 연구 개발을 위해서는 고자장의 마그넷연구가 선행되어야 한다. 고자장을 구현하기 위해서는 저온초전도체를 이용한 마그넷뿐만이 아니라 고온초전도체를 이용한 인서트 코일의 연구가 필요하다. 연세대학교에서는 국가지정연구실사업으로 단백질 구조 규명의 초고자장 NMR 실현을 위한 고온초전도 인서트 코일 기술연구를 진행하고 있다. 본 논문에서는 고온초전도 인서트 코일 연구를 위해 제작할 LTS background magnet과 HTS 인서트 코일에 대한 전자장 해석을 진행하였다. 균일도나 선재 사양 등의 주요 변수 등을 고려하여 LTS background magnet과 HTS 인서트 코일에 적합한 사양을 결정하도록 하였다.

• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.4
• /
• pp.395-401
• /
• 2001

The characteristics of heat transfer and pressure drop through tubes has been investigated experimentally for a compound heat transfer enhancement. The test tubes were spirally indented tubes with wire coil inserts which had a various combinations of pitch and helix angles. Pure water was used as working fluids for the experiments, Heat transfer coefficients and friction factors of the test tubes were evaluated from the values of measured temperatures, flow rates and pressure drops. An performance evaluation was performed to find an optimal combination of spirally indented tubes with wire coil inserts. When the helix angle of wire coil insert are $71^{\circ}-72^{\circ}$, the best heat transfer enhancement was shown. The friction factor was 9 - 13 times higher than those in smooth tubes, and the heat transfer was enhanced a maximum of 500%.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.199-201
• /
• 1996

The design and manufacturing results of a 16 tesla/45mm bore superconducting magnet is presented. The system consists of an 8.2 tesla(at 4.2K) outer NbTi coil with a bore I.D. of 261mm, a winding O.D. of 453mm and the length of 430mm which is connected in series with a 5.6 tesla(at 4.2K) middle and a 4.7 tesla(at 4.2K) inner insert coil constructed of multifilamentary $Nb_3Sn$. The middle and inner insert coil are reacted after winding. Also, epoxy impregnation is accomplished at $Nb_3Sn$ coils using a low viscosity crack resistant epoxy which is forced into the coil with a series of vacuum and over atmosphere pressure cycle.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.1
• /
• pp.45-50
• /
• 2005

Stick type ignition coil(called a Cigar coil) is a kind of transformer for an automobile modulaized of distributer and electric cable. A material of cigar coil is PBT $GF30\%$ resin. This is an excellent engineering plastic with both mechanical and electrical properties. When we insert an HV terminal into the PBT $GF30\%$ resin jacket, it breaks the jacket, because the HV terminal is bigger than the jacket. It is a fatal on durability of a part. In this study, We used ANSYS FEM tool in order to stress analysis by contact. In order to automatically estimate possible maximum diameter of an HV terminal, we used an APDL. In the contact part, we considered the relation of the HV terminal's diameter with the amount of stress that occurred. This relation is able to be applied, in part, to the dimensions of the part design.

• Progress in Superconductivity and Cryogenics
• /
• v.10 no.4
• /
• pp.13-17
• /
• 2008

This paper presents experimental and characteristic analysis of hgh-$T_c$ eater-triggered witch using coated conductor (CC) in liquid and gas helium. The high temperature superconducting insert coil which can be installed in a low temperature superconducting (LTS) magnet has been proposed and researched to generate higher magnetic field for MR. Since CC could be an attractive option for HTS insert, it is important to research he characteristics of heater-triggered switch employing CC. We performed the heater test and constructed simulation model using finite element method (FEM.) We performed a protection test and observed normal zone propagation (NZP) signals to evaluate the witch with protection of magnet.

• Journal of Sensor Science and Technology
• /
• v.20 no.1
• /
• pp.25-29
• /
• 2011

This paper describes the design and analyses of vibration driven electromagnetic energy harvester with high power generation which is suitable for supplying power generator from human body motion. The proposed harvester consists of magnet, coil, and SM (Soft magnetic Material). In order to generate more induced voltage, the SM to concentrate flux lines from end of magnetic poles was arranged into insert moving magnet. Each model was designed and analyzed by using ANSYS software to simulation. The maximum power is generated when load resistance of $1303\;{\Omega}$ is equal to coil resistance. The generated maximum power of for harvesters with SM is $677.85\;{\mu}W$ and 5.46 times higher than without SM at 6 Hz vibration frequency.

• Journal of the Korean Institute of Gas
• /
• v.2 no.4
• /
• pp.25-33
• /
• 1998

The characteristics of evaporation heat transfer for the utilization of LNG cold energy was investigated experimentally using liquified nitrogen and a solution of ethylene-glycol and water under horizontal two-phase conditions in the small-scale equipment of a cryogenic heat exchange system. The inner tubes in the double pipe heat exchanger with 8 mm and 15 mm inner diameter and 6 m length were adopted as a smooth test tubes and enhanced tubes by means of wire-coil inserts. Heat transfer coefficients and Nusselt number for the test tube were calculated from measurements of temperatures, flowrates and pressures. The correlations in a power-law relationship of the Nusselt number, the Reynolds number and Prandtl number for heat transfer were proposed which can be available for design of cryogenic heat exchangers. The correlations showed heat transfer coefficients for the wire-coil inserts were much higher than those for the smooth tubes, increased by more than 2.5 ${\~}$ 5.5 times depending upon the equivalent Reynolds number. Form and length of cryogenic double pipe heat exchanger were proposed for applicable to the utilization of LNG cold energy.

• Journal of Veterinary Clinics
• /
• v.28 no.2
• /
• pp.240-243
• /
• 2011

Several vascular accesses can be used for catheter guided coil embolization for occluding patent ductus arteriosus (PDA). Although trans-femoral approach is most commonly used in dogs, it is often unable to insert angiocatheter for inserting the coil delivery system, especially small puppies weighing less than 2 kg of body weight. Therefore this case study developed trans-carotid method for puppy using JR coronary catheter and free push delivery system. Using this new method, we successfully treated a puppy with PDA weighing 1.25 of body weight.

• Progress in Superconductivity
• /
• v.13 no.1
• /
• pp.1-6
• /
• 2011

Measurement of magnetic signals generated from electric activity of myocardium provides useful information for the functional diagnosis of heart diseases. Key technical component of the magnetocardiography (MCG) technology is SQUID. To measure MCG signals with high signal-to-noise ratio, sensitive SQUID magnetic field sensors are needed. Present magnetic field sensors based on Nb SQUIDs have field sensitivity good enough to measure most of MCG signals. However, for accurate measurement of fine signal pattern or detection of local atrial fibrillation signals, we may need higher field sensitivity. In addition to field sensitivity, economic aspect of the SQUID system is also important. To simplify the SQUID readout electronics, the output voltage or flux-to-voltage transfer of SQUID should be large enough so that direct measurement of SQUID output can be done using room-temperature preamplifiers. Double relaxation oscillation SQUID (DROS), having about 10 times larger flux-to-voltage transfers than those of DC-SQUIDs, was shown to be a good choice to make the electronics compact. For effective cancellation of external noise inside a thin economic shielded room, first-order axial gradiometer with high balance, simple structure and long-baseline is needed. We developed a technology to make the axial gradiometer compact using direct bonding of superconductive wires between pickup coil and input coil. Conventional insert has mechanical support to hold the gradiometer array, and the dewar neck has equal diameter with the dewar bottom. Boiling of the liquid He can generate mechanical vibrations in the gradiometer array due to mechanical connection structure. Elimination of the mechanical support, and direct mounting of the gradiometer array into the dewar bottom can reduce the dewar neck diameter, resulting in the reduction of liquid He consumption.

• Proceedings of the KIEE Conference
• /
• 2004.11c
• /
• pp.474-477
• /
• 2004

This paper deals with a design experience of Control Element Drive Mechanism (CEDM) that is used to withdraw or insert control rods in nuclear reactor. The design is carried out to satisfy the performance requirements for CEDM that were given to ensure reliable and secure actions of the rods. The electrical parameters for four coils that energize the mechanical actuators in CEDM are determined first, Then a computer simulation for CEDM with these coils is performed to see how it works. An adjustment of the coil parameters is made from the simulation results. Finally, it is shown that our final design is valid to guarantee the required performance since the FEM(finite Element Method) calculation shows sufficient vertical attraction forces of a lift armature and a latch magnet, and good dynamics with a full load.