• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.47 no.6
• /
• pp.103-112
• /
• 2010

A study on network traffic analysis and modeling has been exclusively done due to its importance. However, conventional studies on network traffic analysis and modeling only focus on transmitting simple packet stream or traffic features of specific application, such as HTTP. In this paper, we propose a network traffic generator, which reflects the characteristics of multimedia data. To analyze the traffics of online game, which is one of the most popular multimedia contents, we modeled the distribution according to the time between packets and packet size random variable and designed the traffic generator which has the model for input. We generated the traffics of L4D(Left4Dead), WoW(World of Warcraft) with proposed network traffic generator and we found that the generated traffics have similar distributions with real data.

• Tribology and Lubricants
• /
• v.14 no.4
• /
• pp.15-22
• /
• 1998

Recently, the importance of variable displacement piston pump is increasing in industrial world. Especially, most consumers require various range of pressures and flow rates. Pressure compensator is a system controlling flow rate in piston pump at low cost and, therefore, satisfies the need of consumers. However, the system has serious problems, such as response and leakage. The response and leakage are affected by clearance between actuator piston and cylinder, roughness of surface, and spool overlap. In this paper, these effects are investigated experimentally, and optimal clearance and chamfer is obtained. While diameter of cylinder is fixed and diameter of actuator piston is changed in this experiment, response and leakage are measured. Also parameters such as roughness and processing accuracy are changed for piston of fixed clearance. Experimental setup modelled into several parts of actuator piston, cylinder, spool, and swash plate. Input pressure is changed by function generator and proportional valve. The result of this experiment shows that leakage increases very much in proportion to the increase of clearance, and especially leakage occurs enormously when clearance is more than 0.002. The response is not good because as clearance increases leakage increases and as clearance decreases viscous damping effect increases. Accordingly, it is found out that optimal clearance range exists for tile response, within about 0.0012∼0.0014, at this time. Futhermore, the better roughness and geometrical accuracy of actuator piston are, the smaller are leakage and friction. The paper informs that response and leakage are influenced by and geometrical accuracy of actuator piston, roughness of surface, and the clearance between actuator piston and cylinder, and that optimal design of actuator piston in the pressure compensator is possible.

• Journal of Navigation and Port Research
• /
• v.33 no.8
• /
• pp.573-581
• /
• 2009

Today, overall industry has been operated on the basis of information technology and has increased the investment on it. In the logistics industry, the integrated material handling information network has become important more and more and the investment on the informatization has been increased to operate efficiently. In the previous literature, most of the measures for the efficiency of container terminals were the variables such as fixed assets of equipments. There has not been any research effort toward examining the effect of informatization level on the efficiency. This work describes the importance on the efficiency evaluation considering the informatization level to in a container terminal and the relative efficiency level is measured using data envelopment analysis and bootstrap.

• The Journal of Fisheries Business Administration
• /
• v.41 no.3
• /
• pp.129-151
• /
• 2010

This study is to analyze the efficiency of Korean fishing ports using DEA. First, the study calculated the efficiency scores based on a CCR-BCC framework and hence technical, pure technical, and scale efficiency scores are seperated for the 38 fishing ports under study. The Average of technical, pure technical, and scale efficiency are turned out to be 0.6834, 0.8582, and 0.7774 respectively. The 15 fishing ports are fully efficient under the constant returns to scale while 21 fishing ports under the variable returns to scale. Second, the super efficiency scores are also calculated under the radial model without the consideration of slacks. The highest score is turned out to be 4.4984 for the P16 fishing port with the average score of 0.9652 for the entire fishing ports. Nevertheless, P16 fishing port has showed up only once as a reference set. On the other hand, P34 fishing port has showed up 11 times as a reference set, which scored the second highest score of 2.9815. Finally the super efficiency scores are calculated under the non-radial model with the explicit consideration of slacks. Now the P34 fishing port scored the highest score of 2.3424 with even 15 times referred to a bench-mark. Therefore the importance of P34 fishing port is emphasized once again on the field of bench-marking for the efficiency of fishing ports. When the targets for the input factors to improve the efficiency of each DMU are calculated the area of fishing port needs the most adjustment to be reduced for 40.36% on the average, while the cosignment sales area does the least adjustment for 13.70%.

• Journal of Biosystems Engineering
• /
• v.38 no.1
• /
• pp.33-40
• /
• 2013

Purpose: The goal of this study was to build an accurate digital factory that evaluates the performance of a factory using computer simulation. To achieve this goal, we evaluated the effect of worker-related variables on production in a simulation model using comparative analysis of two cases. Methods: The overall work process and worker-related variables were determined and used to build a simulation model. Siemens PLM Software's Plant Simulation was used to build a simulation model. Also, two simulation models were built, where the only difference was the use of the worker-related variable, and the total daily production analyzed and compared in terms of the individual process. Additionally, worker efficiency was evaluated based on worker analysis. Results: When the daily production of the two models were compared, a 0.16% error rate was observed for the model where the worker-related variables were applied and error rate was approximately 5.35% for the model where the worker-related variables were not applied. In addition, the production in the individual processes showed lower error rate in the model that included the worker-related variables than the model where the worker-related variables were not used. Also, among the total of 22 workers, only three workers satisfied the IFRS (International Financial Reporting Standards) suggested worker capacity rate (90%). Conclusions: In the daily total production and individual process production, the model that included the worker-related variables produced results that were closer to the real production values. This result indicates the importance of worker elements as input variables, in regards to building accurate simulation models. Also, as suggested in this study, the model that included the worker-related variables can be utilized to analyze in more detail actual production. The results from this study are expected to be utilized to improve the work process and worker efficiency.

• Structural Engineering and Mechanics
• /
• v.86 no.1
• /
• pp.119-137
• /
• 2023

The purpose of this research is to assess the performance of CBN and ceramic tools during the dry turning of gray cast iron EN GJL-350. During the turning operation, the variable machining parameters are cutting speed, feed rate, depth of cut and type of the cutting material. This contribution consists of two sections, the first one deals with the performance evaluation of four materials in terms of evolution of flank wear, surface roughness (2D and 3D) and cutting forces. The focus of the second section is on statistical analysis, followed by modeling and optimization. The experiments are conducted according to the Taguchi design L₃₂ and based on ANOVA approach to quantify the impact of input factors on the output parameters, namely, the surface roughness (Ra), the cutting force (Fz), the cutting power (Pc), specific cutting energy (Ecs). The RSM method was used to create prediction models of several technical factors (Ra, Fz, Pc, Ecs and MRR). Subsequently, the desirability function approach was used to achieve a multi-objective optimization that encompasses the output parameters simultaneously. The aim is to obtain optimal cutting regimes, following several cases of optimization often encountered in industry. The results found show that the CBN tool is the most efficient cutting material compared to the three ceramics. The optimal combination for the first case where the importance is the same for the different outputs is Vc=660 m/min, f=0.116 mm/rev, ap=0.232 mm and the material CBN. The optimization results have been verified by carrying out confirmation tests.

• Journal of Korean Society on Water Environment
• /
• v.39 no.1
• /
• pp.46-60
• /
• 2023

Climate change causes fluctuations in water quality in the aquatic environment, which can cause changes in water circulation patterns and severe adverse effects on aquatic ecosystems in the future. Therefore, research is needed to predict and respond to water quality changes caused by climate change in advance. In this study, we tried to predict the dissolved oxygen (DO), chlorophyll-a, and turbidity of the Paldang reservoir for about two weeks using long short-term memory (LSTM) and gated recurrent units (GRU), which are deep learning algorithms based on recurrent neural networks. The model was built based on real-time water quality data and meteorological data. The observation period was set from July to September in the summer of 2021 (Period 1) and from March to May in the spring of 2022 (Period 2). We tried to select an algorithm with optimal predictive power for each water quality parameter. In addition, to improve the predictive power of the model, an important variable extraction technique using random forest was used to select only the important variables as input variables. In both Periods 1 and 2, the predictive power after extracting important variables was further improved. Except for DO in Period 2, GRU was selected as the best model in all water quality parameters. This methodology can be useful for preventive water quality management by identifying the variability of water quality in advance and predicting water quality in a short period.

• Journal of Veterinary Clinics
• /
• v.33 no.2
• /
• pp.107-112
• /
• 2016

The objective of this study was to determine potential contributing factors associated with biosecurity level of farrow-to-finish pig farms and to develop a classification tree model to explore how these factors related to each other based on prediction model. To this end, the author analyzed data (n = 193) extracted from a cross-sectional study of 344 farrow-to-finish farms which was conducted between March and September 2014 aimed to explore swine disease status at farm level. Standardized questionnaires with information about basic demographical data and management practices were collected in each farm by on-site visit of trained veterinarians. For the classification of the data sets regarding biosecurity level as a dependent variable and predictor variables, Chi-squared Automatic Interaction Detection (CHAID) algorithm was applied for modeling classification tree. The statistics of misclassification risk was used to evaluate the fitness of the model in terms of prediction results. Categorical multivariate input data (40 variables) was used to construct a classification tree, and the target variable was biosecurity level dichotomized into low versus high. In general, the level of biosecurity was lower in the majority of farms studied, mainly due to the limited implementation of on-farm basic biosecurity measures aimed at controlling the potential introduction and transmission of swine diseases. The CHAID model illustrated the relative importance of significant predictors in explaining the level of biosecurity; maintenance of medical records of treatment and vaccination, use of dedicated clothing to enter the farm, installing fence surrounding the farm perimeter, and periodic monitoring of the herd using written biosecurity plan in place. The misclassification risk estimate of the prediction model was 0.145 with the standard error of 0.025, indicating that 85.5% of the cases could be classified correctly by using the decision rule based on the current tree. Although CHAID approach could provide detailed information and insight about interactions among factors associated with biosecurity level, further evaluation of potential bias intervened in the course of data collection should be included in future studies. In addition, there is still need to validate findings through the external dataset with larger sample size to improve the external validity of the current model.

• Journal of the Korean Association of Geographic Information Studies
• /
• v.11 no.2
• /
• pp.61-72
• /
• 2008

Leaf area index (LAI) is a key biophysical variable influencing land surface processes such as photosynthesis, transpiration and energy balance, and is a required input to estimate evapotranspiration in various ecological and hydrological models. The development of more correct and useful LAIs estimation techniques is required by these importance, but LAIs had been assumed in most LAI research through simple relations with the normalized difference vegetation index (NDVI) because the field measurement is difficult on wide area. This paper is to evaluate the MODIS LAI Product's practical use by comparing with LAIs that is derived from NOAA AVHRR NDVIs and the 2 years (2003-2004) measured LAIs of Korea Forest Research Institute in Gyeongancheon watershed (561.12 $Km^2$). As a result, the MODIS LAIs of deciduous forests showed higher values about 14 % and 15~30 % than the measured LAIs and NOAA LAIs. In the year of 2003, the MODIS LAIs in coniferous forests were 5 % higher than the measured LAIs, and showed about 7 % differences comparing with the NOAA LAIs except April. These differences come from the insufficient field data measured in partial points of the target area, and the extracted reference data from MODIS LAIs include the limits of spatial resolution and the error of incorrect land cover classification. Thus, using the MODIS data by the proper correction with the measured data can be useful as an input data for ecological and hydrological models which offers the vegetation information and simulates the water balance of a given watershed.

• Korean Journal of Remote Sensing
• /
• v.39 no.5_3
• /
• pp.1009-1029
• /
• 2023

Urban trees play a vital role in urban ecosystems,significantly reducing impervious surfaces and impacting carbon cycling within the city. Although previous research has demonstrated the efficacy of employing artificial intelligence in conjunction with airborne light detection and ranging (LiDAR) data to generate urban tree information, the availability and cost constraints associated with LiDAR data pose limitations. Consequently, this study employed freely accessible, high-resolution multispectral satellite imagery (i.e., Sentinel-2 data) to estimate fractional tree canopy cover (FTC) within the urban confines of Suwon, South Korea, employing machine learning techniques. This study leveraged a median composite image derived from a time series of Sentinel-2 images. In order to account for the diverse land cover found in urban areas, the model incorporated three types of input variables: average (mean) and standard deviation (std) values within a 30-meter grid from 10 m resolution of optical indices from Sentinel-2, and fractional coverage for distinct land cover classes within 30 m grids from the existing level 3 land cover map. Four schemes with different combinations of input variables were compared. Notably, when all three factors (i.e., mean, std, and fractional cover) were used to consider the variation of landcover in urban areas(Scheme 4, S4), the machine learning model exhibited improved performance compared to using only the mean of optical indices (Scheme 1). Of the various models proposed, the random forest (RF) model with S4 demonstrated the most remarkable performance, achieving R² of 0.8196, and mean absolute error (MAE) of 0.0749, and a root mean squared error (RMSE) of 0.1022. The std variable exhibited the highest impact on model outputs within the heterogeneous land covers based on the variable importance analysis. This trained RF model with S4 was then applied to the entire Suwon region, consistently delivering robust results with an R² of 0.8702, MAE of 0.0873, and RMSE of 0.1335. The FTC estimation method developed in this study is expected to offer advantages for application in various regions, providing fundamental data for a better understanding of carbon dynamics in urban ecosystems in the future.