• 한국터널지하공간학회 논문집
• /
• 제18권5호
• /
• pp.441-451
• /
• 2016

본 연구에서는 쉴드 TBM에 의한 대심도 복층터널의 계획 시 세그먼트 라이닝의 거동을 주요 구조물인 내부 슬래브의 연결구조 형식에 따라 검토하였다. 복층터널의 내부슬래브와 세그먼트 라이닝 설계 요구조건을 정립하기 위하여 용도에 따라 내부 구조물의 형식을 정의하고, 터널 라이닝과 내부 슬래브의 연결구조를 비교하였다. 그리고 MIDAS Civil 2012 프로그램으로 빔-스프링 모델을 이용하여 수치해석을 수행하였다. 본 연구결과 중간슬래브 및 하부슬래브, 내부슬래브와 세그먼트 라이닝의 연결 형식 그리고 측압계수들은 복층터널 계획시 주요 설계사항임을 확인하였다.

• Advances in concrete construction
• /
• 제14권3호
• /
• pp.195-204
• /
• 2022

As a brittle failure mode, punching-shear failure can be widely found in traditional RC slab-column connections, which may lead to the entire collapse of a flat plate structure. In this paper, a novel RC slab-column connection with inner steel truss was proposed to enhance the punching strength. In the proposed connection, steel trusses, each of which was composed of four steel angles and a series of steel strips, were pre-assembled at the periphery of the column capital and behaved as transverse reinforcements. With the aim of exploring the punching behavior of this novel RC slab-column connection, a static punching test was conducted on two full-scaled RC slab specimens, and the crack patterns, failure modes, load-deflection and load-strain responses were thoroughly analyzed to explore the contribution of the applied inner steel trusses to the overall punching behavior. The test results indicated that all the test specimens suffered the typical punching-shear failure, and the higher punching strength and initial stiffness could be found in the specimen with inner steel trusses. The numerical models of tested specimens were analyzed in ABAQUS. These models were verified by comparing the results of the tests with the results of the analyzes, and subsequently the sensitivity of the punching capacity to different parameters was studied. Based on the test results, a modified critical shear crack theory, which could take the contribution of the steel trusses into account, was put forward to predict the punching strength of this novel RC slab-column connection, and the calculated results agreed well with the test results.

• 콘크리트학회논문집
• /
• 제25권2호
• /
• pp.155-163
• /
• 2013

이 연구는 도넛형 이방향 중공슬래브에 매입된 이형철근의 부착특성 및 부착강도 산정을 위한 기초적인 연구이다. 도넛형 이방향 중공슬래브의 철근 부착특성 및 부착강도 산정을 위해 pull-out test를 수행하였다. 도넛형 중공형성체는 슬래브 내부에 배치되어 철근과 중공형성체 사이에 내부의 피복이 형성된다. 이러한 내부피복두께는 외부피복두께보다 상대적으로 작은 피복두께를 가지며 중공형상에 따라 $2.5d_b$보다 작은 내부피복두께가 형성되기 때문에 철근의 부착에 영향을 미치게 된다. 또한 중공형성체가 일정 간격으로 떨어져 배치되어 있으므로 인장철근을 감싸고 있는 피복두께의 조건이 철근의 길이방향으로 변하게 된다. 따라서 도넛형 이방향 중공슬래브의 부착특성을 알아보기 위해서 중공형성체 형상에 따라 부착구간을 구분하였다. 구간별로 내부피복두께에 따른 부착응력-슬립 관계를 확인하였으며, 중공형성체 전 구간에 걸친 부착응력분포를 확인하여 철근의 길이방향에 따른 부착응력의 발현정도를 확인하였다. 또한 구간별 부착응력-슬립 관계를 기반으로 하여 도넛형 중공슬래브의 부착강도를 산정할 수 있는 부착강도 산정 방법을 제안하였다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2008년도 정기 학술대회
• /
• pp.495-498
• /
• 2008

In this paper applicable range of U-Channel Bridge (UCB) that has recently been introduced as a new bridge type was studied. For structural analysis models used with the frame and plate elements was proposed, and verification of the models were performed. Using these structural models structural analysis of models with span length of 20m-45m and inner width of 5m-13m were performed. As a result for U-shape sections were applicable in the range of 20m span and 35m span, slab was applicable in the range of 5m inner width and 12m inner width. To increase applicable range of UCB H-shape sections and slab with rib were proposed. As a result UCB were applicable in the range of 20m span and 45m span, in the range of 5m inner width and 13m inner width.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2001년도 봄 학술발표회 논문집
• /
• pp.417-422
• /
• 2001

This paper is investigated the coupling effect in slab-wall structural system. An experimental investigation of reinforced concrete wall-slab structures were peformed. For the purpose of this study slab-wall substructures of an apartment building were chosen. And two specimens with different aid ratios have been tested. There were subjected to reserved cyclic loading, consistent with coupling action, with increasing imposed inelastic deformations. From. the result of this test, 1) in slabs, the coupling stress are not uniform across the width, 2) cracks are tending to be concentrated in the regions near the inner edges of the walls, 3) the effective width used in previous theoretical or model studies may not be enough.

• Structural Engineering and Mechanics
• /
• 제86권3호
• /
• pp.417-430
• /
• 2023

As the key part in the reinforced concrete column-steel beam (RCS) frame, the beam-column joints are usually subjected the axial force, shear force and bending moment under seismic actions. With the aim to study the seismic behavior of RCS joints with and without RC slab, the quasi-static cyclic tests results, including hysteretic curves, slab crack development, failure mode, strain distributions, etc. were discussed in detail. It is shown that the composite action between steel beam and RC slab can significantly enhance the initial stiffness and loading capacity, but lead to a changing of the failure mode from beam flexural failure to the joint shear failure. Based on the analysis of shear failure mechanism, the calculation formula accounting for the influence of RC slab was proposed to estimate shear strength of RCS joint. In addition, the finite element model (FEM) was developed by ABAQUS and a series of parametric analysis model with RC slab was conducted to investigate the influence of the face plates thickness, slab reinforcement diameter, beam web strength and inner concrete strength on the shear strength of joints. Finally, the proposed formula in this paper is verified by the experiment and FEM parametric analysis results.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.375-380
• /
• 2002

Tong-young LNG tank is a LNG storage tank of 140,000 kl, and it is composed of Bottom Slab(Annular, Center), Outer Wall, Ring Beam and Roof. Generally, when concrete temperature arise, the complex thermal stress of inner and outer part can cause serious thermal crack and damage at structure. So in this paper, for the control of this thermal crack, we did the concrete mix design with the base of fly-ash 30% substitute at binder, and through the computer modelling at Bottom Slab(Annular, Center), Outer Wall, Ring Beam and Roof, we studied the probability of thermal crack by thermal crack index.

• 대한기계학회논문집A
• /
• 제22권3호
• /
• pp.695-703
• /
• 1998

The crack problem of continuous casting slab due to the thermal stresses during the reheating process is analyzed using FEM. In this study, the C(t)-integral is calculated. As a result, the values of the C(t)-integral decrease by increasing the initial temperature of the slab and decreasing total heat flux. And those decrease by decreasing the heat flux of pre-heating zone and increasing the heat flux of heating zone.

• 한국강구조학회 논문집
• /
• 제17권2호통권75호
• /
• pp.183-194
• /
• 2005

기존의 연속 프리플렉스 거더교는 내측지점부 바닥판 콘크리트에 압축력을 도입시키기 위해 내측지점을 상승시키고 부모멘트 구간만큼의 바닥판 콘크리트를 타설하고 하강시키는 시공법을 사용하였다. 그러나 상기의 시공법은 장시간의 내측지점 상승 작업과 종곡선의 굴곡 문제 등 여러 가지 시공상 문제점을 가지고 있다. 따라서 본 논문은 이러한 문제점을 해소하기 위해 내측지점 및 외측지점을 하강시키는 공정만을 이용한 개선된 연속 프리플렉스 합성형 거더교의 시공법을 제시하였으며, 특정화된 연속 프리플렉스 거더교의 설계 프로그램에만 의존하지 않고 프리플렉스 거더교의 단면을 쉽게 추정할 수 있는 체계화된 설계식을 제시하였다.

• 한국건축시공학회지
• /
• 제21권4호
• /
• pp.293-303
• /
• 2021

국내 PC공장은 PC 유공 슬래브를 생산하기 위해 자동화 설비를 도입하거나 매입물 삽입을 통해 중공 단면을 구현하지만 PC공장의 과다한 초기투자비용이 생산원가의 증가라는 주요 원인으로 작용하기에 다른 대안이 필요한 상황이다. 따라서 본 연구에서는 PC 유공 슬래브 부재 생산시 고무 튜브를 내부 속빈 공간을 형성하는 거푸집으로 사용함으로써 다양한 중공 형상의 성형 및 대단면화, 초경량화, 신속생산 대응 가능을 통한 생산성 확보에 기여하고자 한다.