• 한국항공우주학회지
• /
• 제48권10호
• /
• pp.801-807
• /
• 2020

밸브 입구 압력 변화에 따른 액체로켓엔진용 연소기 산화제 개폐밸브의 개방 특성에 대해 시험을 통한 연구를 수행하였다. 연소기 산화제 개폐밸브의 포핏 방식 밸브 특성에 의해 밸브 입구 압력이 상승함에 따라 밸브 개방에 필요한 구동압력은 선형적으로 증가하며, 밸브 행정 시간은 감소하게 된다. 하지만 밸브 입구 압력 상승으로 밸브 개방 구동압력 도달까지의 시간이 길어져 전체적인 밸브 개방 시간이 증가하는 것으로 나타났다. 결국 밸브 입구 압력이 증가할수록 밸브 행정 시간의 감소량은 미미해지며 밸브 개방에 필요한 구동압력에 도달하는데 필요한 시간이 밸브 개방 시간을 좌우한다는 것을 확인하였다. 따라서 밸브 구동부에 대한 설계를 통해 밸브 개방 시점의 밸브 입구 압력과 연소기로의 순간적인 산화제 공급량을 조정할 수 있다.

• 드라이브 ㆍ 컨트롤
• /
• 제9권4호
• /
• pp.52-57
• /
• 2012

In this study, in order to understand contents and ranges of design for the EGR Valve test system for improving quality and performance of EGR Valve, engine performance and exhaust gas characteristic of 3L-class diesel engine was analyzed. Experimental operation of engine performance test was performed with 50% engine load and 20% and 100% opening ratio of EGR Valve. From test of performance and exhaust gas characteristic of engine, torque output of engine and temperature and pressure of inlet and outlet of EGR Valve were measured. As a result, for design of EGR Valve test system, input fluid flow of EGR Valve must be set the same amount with exhaust gas flow that was below of engine speed of 2,500 rpm, and temperature of inlet of EGR Valve must be set under about $510^{\circ}C$. And the difference of temperature between inlet and outlet of EGR Valve must be over than about $200^{\circ}C$. Exhaust gas of inlet and outlet of EGR Valve were under 1 bar that was not considerable, and the difference of pressure between inlet and outlet of EGR Valve were under 1 bar that could not effect on mechanical operation of EGR Valve.

• 한국생산제조학회지
• /
• 제20권5호
• /
• pp.528-534
• /
• 2011

This study analyzes thermal stress and durability fatigue on the modelling of EGR valve. In case of 10% opening at its inlet, the minimum temperature gets cool as 3 times as inlet temperature. The maximum equivalent stress becomes lowest as the value of $2.6274{\times}109$ Pa and fatigue life becomes highest as 23.657 Cycle. But the minimum temperature gets cool as 2.2 times as inlet temperature in case of 50% opening at its inlet. The equivalent stress becomes higher and fatigue life becomes lower than in case of 10% opening. In case of 100% opening at its inlet, the minimum temperature gets cool as 0.2 times as inlet temperature. The equivalent stress becomes lower and fatigue life becomes higher than in case of 50% opening. Maximum equivalent stress and total deformation are shown at the closing of EGR valve by the pressure of inflow gas. The structural analysis result of this study can be effectively utilized with the design of EGR valve by investigating prevention and durability against its damage.

• 한국산업융합학회 논문집
• /
• 제26권3호
• /
• pp.381-387
• /
• 2023

This study conducts the flow analysis on the basis of the impeller RPM of water measuring valve and differential pressure at valve inlet and outlet. The software used for the flow analysis is STAR-CCM+. In terms of the structure of the measuring valve, it has an impeller installed inside, and a metering chamber has inlet and outlet holes. The flow analysis on the water measuring valve drew the following conclusions: The flow rate and flow coefficient distribution according to the impeller RPM and differential pressure were on the linear increase. Regarding the flow field in the valve, the increased differential pressure had the highest velocity distribution, and complex flow field was generated in the measuring chamber. In particular, since the path between the inlet and outlet holes in the measuring chamber and the valve body was narrow, there was a section that had flow field interference. Given that, it showed the feature of the valve used for water measuring on the basis of the impeller RPM.

• Corrosion Science and Technology
• /
• 제21권1호
• /
• pp.62-67
• /
• 2022

The objective of this study was to perform failure analysis of an inlet pipe located in a governor valve of a steam turbine in a district heating system. During the operation, the temperature of the governor valve was increased to as high as ~500 ℃, which induced thermal expansion of the inlet pipe along both axial and radial directions. While the inlet pipe did not have contact with the valve seat, the side plane of the upside was constrained by the casing part, which led the inlet pipe to experience stress field in the form of fatigue and creep. The primary crack was initiated at about 30 mm below the top where the complex stress field was anticipated. These results suggest that the main failure mechanism is a combination of thermal fatigue and creep during the operation supported by the observation of apparent beach marks on the fracture surface and pores near the cracks, respectively.

• 한국자동차공학회논문집
• /
• 제17권2호
• /
• pp.42-48
• /
• 2009

This paper is the second of 2 companion papers which investigate in-cylinder swirl generation characteristics according to inlet valve angle. Two DOHC 4 valve engines, one has wide intake valve angle and the other has narrow valve angle, were used to compare the characteristics of swirl motion generation in the cylinder. One intake port was deactivated to induce swirl flow. A PIV (Particle Image Velocimetry) was applied to measure in-cylinder velocity field according to inlet valve angle during intake stroke. The results show that the flow patterns of narrow valve engine are much more stable and well arranged compared with the normal engine over the entire intake and compression stroke except early intake stage, and very strong swirl motion is generated at the end of compression stage in this engine nevertheless using straight port which is unfavorable for swirl generating. In the wide valve angle one, however, strong swirl motion induced during intake stroke is destroyed as the compression progresses.

• 한국자동차공학회논문집
• /
• 제16권6호
• /
• pp.148-156
• /
• 2008

This paper is the first of 2 companion papers which investigate in-cylinder swirl generation characteristics according to inlet valve angle. Two DOHC 4 valve engines, one has wide intake valve angle and the other has narrow valve angle, were used to compare the characteristics of swirl motion generation in the cylinder. One intake port was deactivated to induce swirl flow. A PIV (Particle Image Velocimetry) was applied to measure in-cylinder velocity field according to inlet valve angle during intake stroke. The results show that the stronger swirl motion is observed in wide valve angle engine at the early intake stage; however, the swirl motion is gradually distorted by the intake flow component passing through valve area near the cylinder wall as the stroke proceeds. The tumble motion also does so in wide angle. On the contrary, the swirl and tumble motions, which are not clear at the initial stage, become better and better arranged as the piston goes down and up again after bottom dead center.

• Journal of Advanced Marine Engineering and Technology
• /
• 제32권6호
• /
• pp.923-930
• /
• 2008

The butterfly valve is widely used in the industrial field as an on-off or a flow control valve. When the butterfly valve is used as a flow control valve. cavitation sometimes occurs in the range of high flow rate because of the small valve opening. Therefore. the pressure loss and the cavitation characteristics are investigated by use of a commercial CFD code. The results show that the possibility of cavitation occurrence in the cryogenic butterfly valve is very high in the case of valve opening angle below 10 degree and incident velocity over 6m/s. By increasing the inlet velocity at 10 degree of valve opening angle. the value of loss coefficient increased. However. by increasing the inlet velocity at 50 degree of valve opening angle. the value of loss coefficient decreased.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 2008년도 춘계학술 발표회
• /
• pp.161-166
• /
• 2008

본 논문에서는 가솔린 기관에서 흡입 밸브 각도가 엔진의 부분부하 성능에 어떠한 영향을 미치는지를 혼합비 반응 특성을 통해 알아보았다. 흡입 밸브각이 작은 엔진이 흡입 밸브 각이 큰 엔진에 비해 배기가스 중 질소산화물 (BSNOx)의 양은 줄어들었고, 점화시기는 지각되었고, 제동연료소비율은 조금 개선되었다. 배기가스 중 질소산화물의 양이 줄고 점화시기가 지각 되었다는 것은 급속 연소가 일어났다고 판단할 수 있다. 시험 결과를 살펴보면 흡입 밸브각이 작아지면 기관의 연소 성능이 좋아지는 것으로 판단 될 수 있다.

• 대한기계학회논문집
• /
• 제16권7호
• /
• pp.1408-1418
• /
• 1992

본 연구에서는 여러가지 흡기관 조건 및 밸브타이밍 변화에 대하여, 현재까지 연구에서 확인된 IVC에서 흡기포트압력 값의 체적효율에 대한 영향을 검토하고, 흡기 밸브가 열리는 동안 흡기 포트압력의 어느 부분 또는 지점이 엔진의 체적효율 변화를 설명해 줄 수가 있는지를 실험적으로 규명하고자 하였다.이 목적을 위해 각 흡입조 건에 대한 흡기포트압력 및 엔진 성능값을 측정.분석하여 서로의 연관성을 비교, 검토 하였다.