• 한국자동차공학회논문집
• /
• 제8권3호
• /
• pp.28-36
• /
• 2000

Spray characteristics of diesel fuel injection is one of the most important factors in diesel combustion and pollutant emissions especially in HSDI (High Speed Direct Injection) diesel engines where the interval between the onset of combustion and the evaporation of atomized fuel is relatively short, An investigation into various spray characteristics from different holes of VCO(Valve Covered Orifice) nozzles was performed and its results were compared to standard sac nozzle. The global characteristics of spray, including spray angle, spray tip penetration, and spray pattern were measured from the spray images which were frozen by an instantaneous photography with a spark light source. For better understanding of spray behavior, SMD of the fuel sprays from multi hole nozzles were measured with back light imaging while the sprays from the other holes are covered by a purpose-built nozzle cap. The investigation manifestly reveals the different spray patterns at the beginning of injection produced by VCO nozzles can be identified as three distinct types with their own macroscopic and microscopic characteristics, while macroscopic non-uniformity disappears at 0.9∼1.0ms from the start of injection.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.275-278
• /
• 2005

This study has focused on manufacturing technique of powder injection molding of watch case which made from zirconia powder. A series of computer simulation process was applied to prediction of the flow pattern in the inside of the mould and defects as weld line. The material properties of melted feedstock inclusive of the PVT graph and thermal viscosity flowage properties were measured for obtaining the input data in computer simulation. Also, molding experiment was conducted and the results of experiment showed that good agreement with simulation results far flow pattern and weld line location. On the other hand, gravity and inertia effect have an influence on velocity of melt front because of high density of ceramic powder particles in powder injection molding against the polymer injection molding process. In the experiment, the position of melt front was compared with upper gate and lower gate position. The gravity and inertia effect could be confirmed in the experimental results.

• 한국자동차공학회논문집
• /
• 제11권5호
• /
• pp.50-59
• /
• 2003

It was known that high pressure injection is an effective method to enhance thermal efficiency and decrease exhaust emissions in diesel engines. If injection pressure becomes ultra high, it is predicted that there may be a suitable injection pressure which the enhancement rate of spray characteristics is moderate. Also, there may be a limit injection pressure which spray characteristics is reversed and get worse. But these are unknown. To investigate a suitable injection pressure and a limit injection pressure, ultra high pressure injection equipment(UHPIE), which can realize the injection pressure of 3,200bar, was developed. UHPIE is a basic apparatus of single shot injection, and ultra high pressure was achieved by second stage rapid compression in short time. From the evaluation of UHPIE, a injection curve like a conventional diesel engine(jerk type) was realized. Also, it was proved that repetition of experiment was excellent. Therefore it was found that there was no problem to perform the study on the ultra high pressure injection with UHPIE. Consequently, the foundation of the study on ultra high pressure injection could be established.

• 대한기계학회논문집
• /
• 제12권2호
• /
• pp.359-372
• /
• 1988

본 연구에서는 두 노즐간의 거리와 분사압력을 변화시켜 하류로 전개되는 이중분무의 분무형태를 살펴보았다.

• The Korean Journal of Pain
• /
• 제22권1호
• /
• pp.52-57
• /
• 2009

Background: Transforaminal epidural injection (TEI) may be useful to treat unilateral pain that has a dermatomal distribution. In this approach, the needle tip can be placed closer to the dorsal root ganglion and ventral aspect of the nerve root. However many studies have reported that serious complications following TEI occurred more frequently when it was conducted at the cervical level. One of the presumptive mechanisms of the complication is intravascular injection. Therefore this study was conducted to identify the incidence of complications in response to intravascular injections at cervical segments. Methods: This study included all patients, who visited our pain clinic and had radicular symptoms or herpes zoster associated pain. All procedures were conducted under fluoroscopic guidance with contrast enhancement by one of the authors. After the ideal needle position was confirmed by biplanar fluoroscopy, the blood aspiration through the needle hub was evaluated, and a 3 ml mixture of nonionic contrast (2 ml) with normal saline (1 ml) was injected at a rate of 0.3-0.5 ml/sec continuously under real time fluoroscopic visualization. We then classified the contrast spreading pattern as neural, simultaneous neural and vascular, or vascular. Results: A total 71 cervical TEIs were performed. In 26 cases (36.6%), the contrast only spread to the nerve sheath. However, 45 cases (63.4%) showed an intravascular spreading pattern, 37 (52.1%) of which showed a neural and vascular pattern and 8 (11.3%) of which showed only a vascular pattern. Conclusions: Approximately two thirds of the cases of cervical TEI were found to lead to intravascular spreading, which is much higher than the incidence reported in previous studies.

• 동력기계공학회지
• /
• 제5권3호
• /
• pp.17-24
• /
• 2001

In order to investigate a characteristic of the behavior of spray pattern in accordance with running conditions for a DI diesel engine, the PLN Injection system with changeable revolution speed of fuel injection cam was set up, and through this, history curves of injection pressure for a similar real DI diesel engine were able to be displayed. Authors visualized and analyzed the sprays at various revolution speed of fuel injection cam, and found out that fuel distributions of the sprays in the low speed condition were bad, fuel with air was injected from the hole of nozzle at the beginning of injection, and wide spray angle at the early stage of injection became narrower with elapsed time, but wider again at the end of injection.

• 한국정밀공학회지
• /
• 제25권12호
• /
• pp.100-106
• /
• 2008

In this paper, the injection molding process of automotive seat-back cover is analyzed in terms of simulation and of experiment. FE analysis was used to obtain molding conditions such as injection pressure, filling pattern, packing, shrinkage. Vacuum system for low pressure injection molding is developed in the experiment. Low pressure injection molded parts have been compared with conventional molded parts in terms of molding quality and mechanical properties. Based on the results, good product and the productivity improvement can be obtained in low pressure injection molding for automotive seat-back cover.

• 한국기계가공학회지
• /
• 제13권4호
• /
• pp.7-12
• /
• 2014

A transparent poly methyl methacrylate (PMMA) optical micro-pyramid array-pattern is designed and fabricated using an injection modeling technique. The device's optical characteristics are tested and analyzed theoretically. In the optical pattern generated using the fabricated PMMA pattern, the components, due to not only refraction but also diffraction, are observed simultaneously. Wave optic modeling and analysis reveals that the energy ratio between the diffraction and refraction in the optical pattern are dependent on the critical dimension of the optical pattern such that the refraction and diffraction tend to be directly and inversely proportional to the pattern dimension, respectively.

• 한국발생생물학회지:발생과생식
• /
• 제17권4호
• /
• pp.435-440
• /
• 2013

Previous studies, including our own, have demonstrated that the intratesticular injection of hypertonic saline (20%) decreased serum testosterone level which was similar to the surgical castration in the rat, showing the state of chemical castration. In the present study, we further verify the efficacy of this less invasive method as an alternative of surgical orchidectomy in the andrological field. Sterilized 20% saline was directly injected into the adult male rats (750 ${\mu}l$ per testis). The tested rats were divided into 3 groups including intact group (intact), orchidectomy group (ORX) and saline injection group (SAL) after bilateral orchidectomy was performed at the same day of injection. All rats were sacrificed at 4 weeks after injection. The reproductive organs (testes, epididymis, seminal vesicles and prostates) were collected and used for DNA and protein pattern analyses. Also, patho-histological studies on the testes were performed. In contrast to the intact group, similar DNA damages of testis and seminal vesicle were appeared in ORX group and SAL group. The DNA degradations seemed to be the results of necrosis rather than apoptosis. In the protein pattern analysis, all the testing tissues exerted similar patterns in the ORX group and the SAL group compared to the those of intact group. Patho-histological studies revealed that severe degenerative changes in testicular seminiferous tubules and massive infiltration of immune cells in SAL group. The present study confirmed that direct injection of hypertonic saline into the testis caused the equivalent biochemical changes in the accessory sex organs as shown in the orchidectomized animals. These results suggest that hypertonic saline injection model could be a useful castration model which can substitute for surgical castration when its safety is secured through further study in the future.

• 소성∙가공
• /
• 제16권1호
• /
• pp.9-14
• /
• 2007

In this paper, a mold temperature control method for injection molding is proposed. The inner surface of mold is locally heated by jet impingement to improve pattern transcription. Heating by hot jet is completed while the mold is open. An experimental system that realizes the proposed idea has been built, which includes mold, nozzle assembly and heater. Actual injection molding process including the proposed heating procedure has been conducted to verify the validity of the method. The process has been done for several conditions with different jet temperatures and duration of heating. The results from different conditions are compared.