• Transactions of the Korean Society of Automotive Engineers
• /
• v.20 no.4
• /
• pp.150-155
• /
• 2012

Lean NOx Trap (LNT) catalysts are capable of reducing exhaust NOx emissions from diesel engines. LNT stores NOx in lean condition and exhausts N2 by reducing NOx in rich condition. NOx reduction characteristic of LNT catalysts using throttle position sensor and fuel injection timing control for light-duty diesel engine was investigated. In contrast to SCR system, LNT catalyst uses diesel fuel in resuctant. Also if the concentration of reductant is exceeded, excessive amount of reductant will slip throughout LNT and cause another emission problem. Thus LNT regeneration with precise engine control established that can make higher NOx conversion efficiency and lower fuel penalty, prevent another emission problem. NOx and reductant concentration were measured by the NOx sensor and Mexa7100D equipped inlet and outlet of catalyst. As a result of engine test, regeneration strategy has reached high of 77.8% NOx conversion efficiency according to engine operation condition. Moreover, we have proved that it is possible to use regeneration strategy of LNT within 5% fuel penalty.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.1
• /
• pp.117-124
• /
• 2011

Automotive engines require strategies to fulfill the emission regulations in terms of NOx and PM. A dramatic reduction in NOx and PM emissions could be achieved with high pressure injection, innovative combustion strategies and EGR. Recently, Lean NOx Trap (LNT) and Urea-SCR are considered as more practical strategy to suppress the engine-out emissions substantially for copying with severe regulation. These systems need to reduce the reducing agent injection system which has a huge impact on NOx purification efficiency. In this paper, different three injectors have been used to investigate spray characteristics and engine emission test was conducted to clarify the effect of these injectors on the NOx reduction.

• Journal of the korean Society of Automotive Engineers
• /
• v.14 no.6
• /
• pp.67-73
• /
• 1992

This paper describes Hyundai's research and development work on a flexible fuel vehicle (FFV). The work on FFV has been conducted to evaluate its potential as an alternative to the conventional gasoline vehicle. Hyundai FFV described here can be operated on M85, gasoline, or any of their combinations, in which the methanol concentration is measured by an electrostatic type fuel sensor. For that operation, a special FFV ECU(Eletronic Control Unit) has been developed and incorporated in the FFV. The characteristics affecting FFV operation, such as FFV ECU control strategy and injector flow rate, have been investigated and optimized through the experiment. And various development tests have been performed in view of engine performance, durability, cold startability, and exhaust emissions reduction. The exhaust gas aftertreatment system consisting of manifold type catalyst and secondary air injection system shows good emission reduction performance including formaldehyde, and finally, the possibility of the FFVs as the low emission vehicles is evaluated by presenting NMOG(Non-Methane Organic Gases) levels with respect to M0 and M85. With these results, it is concluded that FFV can be a candidate for the low emission vehicles, but more works on its durability improvement is required.

• The Journal of Korean Medicine
• /
• v.26 no.4
• /
• pp.98-107
• /
• 2005

Objectives: Acupuncture treatment has been clinically used for functional recovery in Parkinson's disease. In the present study, we investigated the effect of acupuncture at Zusanli (ST36) on nigrostriatal dopaminergic neuronal cell death in rats. Methods: A Parkinson's disease model was induced by the unilateral injection of 6-hydroxydopamine (6-OHDA) into the striatum. Acupuncture treatment was performed at Zusanli (ST36) and at the hip, as a non-acupoint, once a day for 14 days. Two weeks after 6-0HDA injection, an apomorphine-induced rotational behavior test showed significant rotational asymmetry in rats with Parkinson's disease. Immunostaining for tyrosine hydroxylase demonstrated a dopaminergic neuronal loss in the substantia nigra and dopaminergic fiber loss in the striatum. Results: Acupuncture at the ST36 acupoint significantly inhibited rotational asymmetry in rats with Parkinson's disease, and also protected against 6-OHDA-induced nigrostriatal dopaminergic neuronal loss. These effects of acupuncture were not observed for non-acupoint acupuncture. Conclusions: The present study shows that acupuncture treatment, especially at the ST36 acupoint, can be used as a useful strategy for the treatment of Parkinson's disease.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.2
• /
• pp.78-83
• /
• 2011

Diesel engine has many advantages such as high thermal efficiency, low fuel consumption and low emission of CO2. However, the diesel engine faced with strengthened emission regulation about NOx and PM. To suppress NOx emission, after-treatment systems such as Lean NOx Trap (LNT), Selective Catalytic Reduction (SCR) are considered as a more practical strategy. This paper investigated the performance of Lean NOx trap of the 4 stroke diesel engine which had a LNT catalyst. Characteristic of exhaust emission at NEDC mode was analyzed. From this result, the effect of nozzle attaching degree, injection quantity and gas flow change on NOx conversion performance was clarified.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.91-97
• /
• 2010

This paper described the effects of DME blended fuel on the engine combustion and emission characteristics of four cylinder CRDI diesel engine. Biodiesel was added into the DME fuel in order to improve the low kinematic viscosity of DME fuel. In this work, the experiment was performed under th various injection timings and injection strategy at constant engine speed and engine load. To maintain the fuel pressure and temperature, pressure and temperature controllers were installed to the DME fuel system. The results show that ignition delay was shortened and combustion duration was extended when DME blended fuel is supplied. Despite of slightly higher NOx emission with DME blended fuel at equal conditions in comparison with those of diesel fuel, the engine showed lower HC and CO emission characteristics.

• Archives of Plastic Surgery
• /
• v.47 no.3
• /
• pp.256-262
• /
• 2020

Background Most women consider an oval-shaped face to be youthful and beautiful. In recent years, demand has grown for surgical procedures with a shorter downtime and fewer complications. These minimally invasive procedures include botulinum toxin type A (BoNTA) injection, filler injection, suction-assisted liposuction (SAL), laser-assisted lipolysis (LAL), thread lifting, and fat grafting. This study aims to introduce an effective method for creating an aesthetically pleasing lower face using a combination of minimally invasive procedures. Methods From March 2017 to March 2019, 94 patients simultaneously underwent LAL, SAL, and thread lifting. Ancillary procedures such as BoNTA injections, hyaluronic acid filler injections, and removal of the buccal fat pad (BFP) were selectively performed according to the patient's condition. Results Patients rated their postoperative satisfaction as very satisfied, satisfied, dissatisfied, or very dissatisfied. Approximately 83% of all respondents were satisfied with the results, whereas the remaining respondents had complaints regarding the outcomes. The most common reasons for dissatisfaction were a longer-than-expected recovery time and undercorrection, and the most severe complaint was skin depression as a result of overcorrection. Conclusions Our method of simultaneously performing LAL, SAL, and thread lifting, while adding BoNTA, filler injections, and BFP removal as needed, was capable of producing consistent and reliable aesthetic outcomes for the lower face.

• Journal of ILASS-Korea
• /
• v.20 no.4
• /
• pp.247-253
• /
• 2015

Recently, the engine calibration technique has been much more complicated than that of the past engine case in order to satisfy the strict emission regulations. The current calibration method for the diesel engine which has an increasing market is both costly and time-consuming. New engine calibration method is required to develop for high-quality diesel engines with low cost and release it at the appropriate time. This study provides the optimal calibrating technique for complex engine systems using statistical modeling and numerical optimization. Firstly, it design a test plan based on Design of Experiments, a V-optimality methodology which is suitable looking for set-points, and determine the shape of test engine response. Secondly, it uses functions to make linear regression model for data analysis and optimization to fit the models of engines behavior. Finally, it generates the optimal calibrations obtained directly from empirical engine models using Grey Relational Analysis and compares the calibrations with data. This method can develop a process for systematically identifying the optimal balance of engine emissions.

• Journal of Power Electronics
• /
• v.12 no.5
• /
• pp.800-812
• /
• 2012

This paper analyses the mathematical model and control strategies of a Hybrid Active Power Filter with Injection Circuit (IHAPF). The control strategy based on the load harmonic current detection is selected. A novel control method for a IHAPF, which is based on the analyzed control mathematical model, is proposed. It consists of two closed-control loops. The upper closed-control loop consists of a single fuzzy logic controller and the IHAPF model, while the lower closed-control loop is composed of an Adaptive Network based Fuzzy Inference System (ANFIS) controller, a Neural Generalized Predictive (NGP) regulator and the IHAPF model. The purpose of the lower closed-control loop is to improve the performance of the upper closed-control loop. When compared to other control methods, the simulation and experimental results show that the proposed control method has the advantages of a shorter response time, good online control and very effective harmonics reduction.

• Design & Manufacturing
• /
• v.13 no.1
• /
• pp.25-30
• /
• 2019

This paper presents the design strategy for the optimal RTM molds of Carbon Fiber Reinforced Plastic (CFRP) by carbon fiber draping and resin flow simulation. First, the mold shape and molding condition were determined considering the undercut and die face of the product in the draping simulation, which made the preliminary shape of the product by compressing the carbon fiber. After that, the diffusion behavior during the injection of resin in the mold was predicted by the resin flow simulation. Finally, the optimal mold shape was designed by selecting the locations of resin injection port and vent based on total results of simulations. In this paper, the mold of automotive side mirror case was selected as the representative product. Also, the actual mold was manufactured based on the simulation design to confirm the practicality of it. This study is expected to contribute to the industry as a technology to improve the reliability and productivity of CFRP producted by RTM process.