• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.186-191
• /
• 2008

Injection molding is used to manufacture various kinds of products including very thin plate like frames. One such product is Door video phone system Panel which is our present object of investigation. During the molding process, large deflection problems in the final product always provokes for the several trials for the accuracy. To solve the issue we use Moldflow6.2 which is injection molding simulation software. It simulates the product exactly the way it happens in actual manufacturing environment. Differences in the geometrical parameters such as thickness changes will lead to the large deformation problems in the frame. However in our present study we simulate it in a well defined condition under several trials. Interesting observations are made in minimizing the deformation of the frame during the injection molding process. This way of approach is very useful in further works if any changes have to be made in the product.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.275-278
• /
• 2005

This study has focused on manufacturing technique of powder injection molding of watch case which made from zirconia powder. A series of computer simulation process was applied to prediction of the flow pattern in the inside of the mould and defects as weld line. The material properties of melted feedstock inclusive of the PVT graph and thermal viscosity flowage properties were measured for obtaining the input data in computer simulation. Also, molding experiment was conducted and the results of experiment showed that good agreement with simulation results far flow pattern and weld line location. On the other hand, gravity and inertia effect have an influence on velocity of melt front because of high density of ceramic powder particles in powder injection molding against the polymer injection molding process. In the experiment, the position of melt front was compared with upper gate and lower gate position. The gravity and inertia effect could be confirmed in the experimental results.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 The Korea-Japan Plastics Processing Joint Seminar
• /
• pp.27-32
• /
• 2003

The wavelike flow mark phenomenon is one of the surface defects that can arise during the injection stage of the injection molding process. We have performed a numerical analysis using a finite element method for the injection molding to verify the validity of 'Go-over' hypothesis. Also, we have compared the results of numerical analysis with available experimental data. Numerical analysis results of the flow marks are qualitatively in good agreement with experimental data of reference, but are quantitatively deviated from experimental data in a consistent manner. A parametric study has been performed to examine the correlative effects of various injection molding processing parameters and material properties on the flow mark size.

• 소성∙가공
• /
• 제18권2호
• /
• pp.128-134
• /
• 2009

The present study covers an integrated simulation method to evaluate optical performance of an aspheric plastic lens by connecting an injection molding analysis with a ray tracing simulation. Traditional ray tracing methods have based on the assumption that the optical properties of a lens are homogeneous throughout the entire volume. This assumption is to a certain extent unrealistic for injection-molded plastic lenses because material properties vary at every point due to the injection molding effects. To take into account the effects of the inhomogeneous optical properties of the molded lens, a numerical scheme is developed to calculate the distribution of refractive index induced from the injection molding process. This index distribution is then reflected onto CODE $V^{(R)}$ simulation and used to calculate ray paths in inhomogeneous media. The proposed tracing scheme is implemented on the tracing of an aspheric lens for a mobile phone camera module.

• 소성∙가공
• /
• 제16권1호
• /
• pp.61-66
• /
• 2007

Powder injection molding(PIM) is widely used for many parts in the field of automotives, electronics and medical industries, due to the capability of net shaping for complex 3-D geometry. Powder injection mold design for the dental scaler tip, a component of medical appliance, was presented. In comparison with conventional machining process, powder injection molding has many advantages, specially in price and dimensional stability, for molding dental scaler tip which has complex geometry. Both product design and mold design for dental scaler tip were presented. A PIM feedstock was made of stainless series(17-4PH, 316L, 440C) powder and a wax based binder. The 'rapid mold' concept was applied to manufacture the various forms and materials of dental scaler tip including vibration characteristics.

• 소성∙가공
• /
• 제11권8호
• /
• pp.691-700
• /
• 2002

Injection molded plastic parts have many surface detects: weld line, sink mark, flow mark, gloss, shading, scratching, and so on. Because these surface faults have not been accepted esthetically, plastic parts are Produced through painting or texturing. The purpose of this paper is to develop a paintless molded part of TV Mask Front by flow control method and gas-assisted injection molding. In order to minimize defects from injection molding, this study was carried out using computer aided injection mold filling simulations using MF/FLOW and MF/GAS. Based on these numerical results, we developed FR(Flame Retardant) HIPS and established guidelines of part design, mold design, and Processing conditions. We have achieved of cost sayings, improvement of productivity, and utilization of recycling by eliminating surface defects and painting process.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 춘계학술대회논문집
• /
• pp.474-480
• /
• 2003

The wavelike flow mark phenomenon is one of the surface defects that can arise during the injection stage of the injection molding process. We have performed a numerical analysis using a finite element method for the injection molding to verify the validity of “Go-over” hypothesis. Also, we have compared the results of numerical analysis with available experimental data. Numerical analysis results of the flow marks are qualitatively in good agreement with experimental data of reference, but are quantitatively deviated from experimental data in a consistent manner. A parametric study has been performed to examine the correlative effects of various injection molding processing parameters and material properties on the flow mark size.

• 유변학
• /
• 제11권2호
• /
• pp.159-167
• /
• 1999

샌드위치 사출성형 공정은 기존의 사출성형 공정이 가지지 못하는 여러 장점들로 인해 최근 산업적으로 주목 받고 있는 고분자 가공 공정이다. 이 공정의 해석적인 접근은 거의 불가능하므로, 본 연구에서는 수치모사를 통해서 샌드위치 사출성형의 충전 공정을 연구하였다. 수치모사는 기본적으로 유한요소법을 사용하였고 Flow Analysis Network(FAN)/관할체적(Control Volume)법 등을 함께 이용하였다. 그리고 skin polymer의 선단을 확인할 수 있는 기존의 충전율 변수와 함께 skin polymer와 core polymer의 경계를 표시하는 새로운 충전율 변수를 도입하였고 이것을 이용하여 core polymer의 선단을 추적하였다. 새로운 충전율 변수는 두께 방향으로 온도장을 풀기 위해 나눈 각 층에서 정의되었다. 수치모사에 사용된 skin polymer와 core polymer로는 물성이 다른 두 고분자 물질을 주입시켜서 나타나는 충전 형태를 비교했다. 즉, 점도 상수, power-law 지수 등과 같은 유변 물성이 다른 두 고분자 물질을 충전시키기 위해 공정상 필요한 입구에서의 압력 등을 계산했으며 나중에 들어가게 되는 core polymer의 충전 완료 후 금형 내에서의 두께 방향과 흐름 방향으로의 분포 등을 구하였다. 또한 실제 공정 상에서 가공조건에 해당되는 switchover time과 벽 온도 등의 조건을 바꿔가면서 수치모사를 진행하였다. 사례 연구를 통하여 얻어진 물성과 가공 조건에 따른 core polymer의 충전 형태와 입구에서의 압력 등은 샌드위치 사출성형의 산업적 이용에 매우 유용하게 사용될 수 있다.

• Korean Chemical Engineering Research
• /
• 제48권4호
• /
• pp.490-498
• /
• 2010

K사의 방진고무 사출성형에 있어서 애로사항인 토크로드부시(torque rod bush)의 캐비티 가장자리(edge) 구간에서의 에어트랩(air-trap) 발생 및 다이내믹 댐퍼(dynamic damper)에 있어서 사출시 미성형(short shot) 발생 등의 문제점을 해결하기 위하여, 상용 CAE 프로그램인 MOLDFLOW(Ver. 5.2)를 이용한 전산모사를 수행하여 적정금형설계를 도출하고 적정작업조건을 구축하였다. 그 결과 방진고무 중에서 토크로드부시의 사출성형에서의 에어트랩 발생 등의 공정문제를 최적 캐비티 가장자리 경사각 및 게이트 수를 조절함으로써 캐비티 가장자리에서의 유동선단(flow-front)의 유동정체를 방지하고 유동을 원활하게 하여 해결하였다. 한편 다이내믹 댐퍼의 사출시 충전(filling) 단계에서의 캐비티 비충전으로 인한 미성형 불량은 에어벤트(air-vent) 구를 에어트랩 발생 빈도가 매우 높은 유동선단 상향류와 하향류의 두 흐름이 만나는 지점에 설치함으로써 미성형 불량을 해결하였다. 또한 게이트 위치를 댐퍼 상단에서 중단으로 변경하거나 게이트 수를 증가시킨 경우에 미성형 불량이 K사의 경우보다 개선되었다.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1986년도 한국자동제어학술회의논문집; 한국과학기술대학, 충남; 17-18 Oct. 1986
• /
• pp.431-436
• /
• 1986

The design and manufacture of injection molded polymeic parts with desired mechanical properties is a costly process dominated by empiricism, including the modification of actual tooling. This paper presents an interactive computer-based design system for injection molded plastic parts. This knowledge-based synthesis system provides a rational design strategy for injection molding and molded parts. It synergistically combines a rule-based expert system for hurestic knowledge with analytical process simulation programs. The theremomechanical properties of a molded part such as the effect of molecular orientation and weldline strength are predicted by the analysis programs; while the expert system interprets the analytical results from the process simulation, evaluates the design, and generates recommendations for optimal design alternatives. The heuristic knowledge of injection molding is formalized as production rules of the expert consultation system.