• Journal of Institute of Control, Robotics and Systems
• /
• v.20 no.9
• /
• pp.914-921
• /
• 2014

In this paper, an algorithm is suggested to detect an offset angle of the absolute rotor position sensor after the initial assembly of a PMSG. Unlike previous studies in a stationary state, this one is not designed to detect an electrical angle but rather the absolute position of the rotor is detected while operating the generator. Also,a position sensor, current sensors and voltage sensor were used to ensure reliability. This technique completes the detection of the sensor offset in two steps. In the first step, a zero-crossing of the EMF is measured using a voltage sensor to detect the electrical angle offset when the alternator is actuated by the engine. In the second step, a high frequency current is injected along the d-axis on-line during the control of the generation, eventually to obtain the inductance using a DFT (Discrete Fourier Transform), and then to ultimately extract the final electrical angle offset through the comparison of the inductance magnitude. The suggested algorithm was validated with PSIM simulation and, furthermore, was tested with actual experiments on a dynamometer.

• The Journal of the Acoustical Society of Korea
• /
• v.18 no.3
• /
• pp.49-54
• /
• 1999

In this paper, we propose a new method to estimate the initial DOA of a new appearing source in wideband multisource beamforming and tacking with array sensor position calibration algorithm. By using a beampattern formula for initial DOA detection, the proposed method keeps estimation error within possible tracking range and can be applied to several beamformers with different mainlobe width by adjusting DOA resolution. The simulation results show the performances of source detection and tracking.

• Journal of IKEEE
• /
• v.24 no.4
• /
• pp.1004-1010
• /
• 2020

This paper proposes an initial rotor magnetic pole detection method for single-phase permanent magnet synchronous motors. The target motor cannot obtain position information based on the back emf in the low speed and stop state. Therefore, an open loop starting process is required, and in this process, initial rotor position information for low current and soft start is need. The proposed initial rotor magnetic pole detection algorithm considers the effect of asymmetric air- gap and magnetic flux. In addition, the high-frequency voltage signal injection and the offset voltage for accurate detection is used. As a result, the permanent magnet poles are is determined by acquiring the maximum value of the induced current using the virtual dq-axis.

• Journal of Korea Multimedia Society
• /
• v.13 no.5
• /
• pp.702-709
• /
• 2010

The performance of mass segmentation is greatly influenced by an initial position of a mass. Some researchers performed mass segmentation with the initial position of a mass given by radiologists. The purpose of our research is to find the initial position for mass segmentation and to notify the segmented mass to radiologists without any additional information on mammograms. The proposed system consists of breast segmentation by region growing and opening operations, decision of an initial seed with characteristics of masses, and mass segmentation by a level set segmentation. A seed for mass segmentation is set based on mass scoring measure calculated by block-based variances and masked information in a sub-sampled mammogram. We used a DDSM database to evaluate the system. The accuracy of mass detection is 78% sensitivity at 4 FP/image, and it reached 92% if multiple views for masses were considered.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.8 no.4
• /
• pp.344-350
• /
• 2003

In this paper, an estimation technique of initial rotor position at standstill in Switched Reluctance Motor(SRM) is proposed. In case search coils are used as a position sensor, it has many advantages like low cost, decrease in the volume, high robust characteristics and wide applications. However, the initial rotor position detection is very difficult because the search coil's EMF is not exist at a standstill. In this paper, a near estimation method of initial rotor position is suggested using squared Euclidean distance. The simulation and experiment for the proposed method are achieved. The validity of the proposed method is verified by experimental results.

• Journal of Institute of Control, Robotics and Systems
• /
• v.2 no.4
• /
• pp.330-336
• /
• 1996

An real-time active beacon localization system for mobile robots is developed and implemented. This system permits the estimation of robot positions when detecting light sources by PSD(Position Sensitive Detector) sensor which are placed sparsely over the robots work space as beacons(or landmarks). An LSE(Least Square Estimation) method is introduced to calibrate the internal parameters of a model for the beacon and robot position. The proposed system has two operational modes of position estimation. One is the initial position calculation by the detection of two or more light sources positions of which are known. The other is the continuous position compensation that calculates the position and heading of the robot using the IEKF(Iterated Extended Kalman Filter) applied to the beacon and dead-reckoning data. Practical experiments show that the estimated position obtained by this system is precise enough to be useful for the navigation of robots.

• 제어로봇시스템학회:학술대회논문집
• /
• 1996.10b
• /
• pp.916-919
• /
• 1996

An real-time active beacon localization system for mobile robots is developed and implemented. This system permits the estimation of robot positions when detecting light sources by PSD(Position Sensitive Detector) sensor which are placed sparsely over the robot's work space as beacons(or landmarks). An LSE(Least Square Estimation) method is introduced to calibrate the internal parameters of a model for the beacon and robot position. The proposed system has two operational modes of position estimation. One is the initial position calculation by the detection of two or more light sources positions of which are known. The other is the continuous position compensation that calculates the position and heading of the robot using the IEKF(Iterated Extended Kalman Filter) applied to the beacon and dead-reckoning data. Practical experiments show that the estimated position obtained by this system is precise enough to be useful for the navigation of robots.

• Speech Sciences
• /
• v.14 no.1
• /
• pp.37-62
• /
• 2007

The current study examines the role of post-lexical tonal patterns of a prosodic phrase in word segmentation. In a word spotting experiment, native Korean listeners were asked to spot a disyllabic or trisyllabic word from twelve syllable speech stream that was composed of three Accentual Phrases (AP). Words occurred with various post-lexical intonation patterns. The results showed that listeners spotted more words in phrase-initial than in phrase-medial position, suggesting that the AP-final H tone from the preceding AP helped listeners to segment the phrase-initial word in the target AP. Results also showed that listeners' error rates were significantly lower when words occurred with initial rising tonal pattern, which is the most frequent intonational pattern imposed upon multisyllabic words in Korean, than with non-rising patterns. This result was observed both in AP-initial and in AP-medial positions, regardless of the frequency and legality of overall AP tonal patterns. Tonal cues other than initial rising tone did not positively influence the error rate. These results not only indicate that rising tone in AP-initial and AP_final position is a reliable cue for word boundary detection for Korean listeners, but further suggest that phrasal intonation contours serve as a possible word boundary cue in languages without lexical prominence.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.16 no.6
• /
• pp.134-140
• /
• 2008

Preceding vehicle detection is a crucial issue for driver assistance system as well as for autonomous vehicle guidance function and it has to be performed with high reliability to avoid any potential collision. The vision-based preceded vehicle detection systems are regarded promising for this purpose because they require little infrastructure on a highway. However, the feasibility of these systems in passenger car requires accurate and robust sensing performance. In this paper, an preceded vehicle detection system is developed using stereo vision sensors. This system utilizes feature matching, epipoplar constraint and feature aggregation in order to robustly detect the initial corresponding pairs. After the initial detection, the system executes the tracking algorithm for the preceded vehicles including a leading vehicle. Then, the position parameters of the preceded vehicles or leading vehicles can be obtained. The proposed preceded vehicle detection system is implemented on a passenger car and its performances is verified experimentally.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.18 no.6
• /
• pp.556-564
• /
• 2013

This paper proposes an initial rotor position detecting algorithm of a PM synchronous motor using an incremental encoder. The proposed algorithm estimates the phase offset between the rotor magnetic flux and the Z-pulse of the incremental encoder by applying six aligning mode current control. The absolute rotor position for driving a PM synchronous motor is calculated by using the phase offset of the Z pulse and A, B pulse signals of the encoder. The PMSM drives based on the estimated rotor position is applied to the elevator door system. The door length is measured on line at first setup of the elevator. The speed control for open, close, and reopen of the elevator door is also presented and the proposed algorithm for the elevator door system is verified by experiment.