• Steel and Composite Structures
• /
• 제25권1호
• /
• pp.79-92
• /
• 2017

Initial damage to a stud due to corrosion, fatigue, unexpected overloading, a weld defect or other factors could degrade the shear capacity of the stud. Based on typical push-out tests, a FEM model and theoretical formulations were proposed in this study. Six specimens with the same geometric dimensions were tested to investigate the effect of the damage degree and location on the static behavior and shear capacity of stud shear connectors. The test results indicated that a reduction of up to 36.6% and 62.9% of the section area of the shank could result in a dropping rate of 7.9% and 57.2%, respectively, compared to the standard specimen shear capacity. Numerical analysis was performed to simulate the push-out test and validated against test results. A parametrical study was performed to further investigate the damage degree and location on the shear capacity of studs based on the proposed numerical model. It was demonstrated that the shear capacity was not sensitive to the damage degree when the damage section was located at 0.5d, where d is the shank diameter, from the stud root, even if the stud had a significant reduction in area. Finally, a theoretical formula with a reduction factor K was proposed to consider the reduction of the shear capacity due to the presence of initial damage. Calculating K was accomplished in two ways: a linear relationship and a square relationship with the damage degree corresponding to the shear capacity dominated by the section area and the nominal diameter of the damaged stud. This coefficient was applied using Eurocode 4, AASHTO LRFD (2014) and GB50017-2003 (2003) and compared with the test results found in the literature. It was found that the proposed method produced good predictions of the shear capacity of stud shear connectors with initial damage.

• International Journal of Contents
• /
• 제9권1호
• /
• pp.6-10
• /
• 2013

Foreground estimation in object segmentation has been an important issue for last few decades. In this paper we propose a GrabCut based automatic foreground estimation method using block clustering. GrabCut is one of popular algorithms for image segmentation in 2D image. However GrabCut is semi-automatic algorithm. So it requires the user input a rough boundary for foreground and background. Typically, the user draws a rectangle around the object of interest manually. The goal of proposed method is to generate an initial rectangle automatically. In order to create initial rectangle, we use Gabor filter and Saliency map and then we use 4 features (amount of area, variance, amount of class with boundary area, amount of class with saliency map) to categorize foreground and background. From the experimental results, our proposed algorithm can achieve satisfactory accuracy in object segmentation without any prior information by the user.

• 한국정밀공학회지
• /
• 제14권6호
• /
• pp.135-141
• /
• 1997

Low velocity impact test and compressive residual strength test after impact were performed by using Hercules AS4/3501-6[45/0/-45/90]$_{2s}$ laminated plate to investigate the low velocity impact damage behavior and the post-impact strength degradation on orthotropic composite laminate plate. Due to the lateral impact losd, the load path showed "" shape according to the laminate central deflection. Damage in a laminate occurs by inclined matrix crack at the damage initiation load stage and vertical matrix crack, occurs on the outer surface. Evaluating the compressive residual strength after the low velocty impact test, it could be found that there is a transient range where the compressive residual strength drop suddenly in the initial damage which is in the matrix crack range and the initial delamination area. is in the matrix crack range and the initial delamination area.

• 한국군사과학기술학회지
• /
• 제27권2호
• /
• pp.230-237
• /
• 2024

Dispersion munitions are often equipped with dispersive submunitions used to scatter bombs over a wide area, and one of the types of dispersive submunitions is the Magnus rotor, commonly referred to as a self-rotating flying body. The Magnus rotor is designed to be dispered over a wide area by utilizing the principle of the Magnus effect through self-rotation, and has various trajectories depending on the initial conditions from the mother dispersion munition. In this paper, an index to evaluate the dispersion uniformity of footprint of the dispersive submunition is presented and the dispersion uniformity according to various initial release conditions is evaluated, and it is getting larger with high incidence angle and get max value at certain initial angular velocity.

• Asian Pacific Journal of Cancer Prevention
• /
• 제16권13호
• /
• pp.5573-5578
• /
• 2015

Background: A systematic review and meta-analysis were performed to compare the post-recurrence survival with hepatic re-resection versus transarterial chemoembolization (TACE) for recurrent hepatocellular carcinoma (HCC) after initial resection. Materials and Methods: All relevant papers were searched via PubMed, EMBASE, and Cochrane Library databases. Hazard ratios (HRs) with 95% confidence intervals (CIs) were pooled using a random-effects model. Subgroup analysis was performed according to country. Sensitivity analysis was performed in studies which clearly reported the recurrent regions, in moderate/high-quality studies, in studies published in full-text form, and in studies published after 2005. Results: In total, twelve papers were included in our study. Five and seven of them were of moderate- and poor-quality, respectively. The overall meta-analysis demonstrated a statistically significantly higher post-recurrence survival in the hepatic re-resection group than in those undergoing TACE (HR=0.64, 95%CI=0.52-0.79, P<0.0001). Heterogeneity was statistically significant and statistical significance remained in the subgroup analysis. Sensitivity analyses were also consistent with the overall analysis. Conclusions: Hepatic re-resection might provide a better post-recurrence survival than TACE for recurrent HCC after initial resection. However, considering the low quality of published studies and the potential bias of treatment selection, further randomized trials should be warranted to confirm these findings.

• 한국입자에어로졸학회지
• /
• 제7권3호
• /
• pp.99-108
• /
• 2011

To establish area specific control strategies for the reduction of the ozone concentration, the Ozone Isopleth Plotting Package for Research(OZIPR) model has been widely used. However, the model results tend to changed by various input parameters such as the background concentration, emission amount of NOx and volatile organic compounds (VOCs), and meteorological condition. Thus, sensitivity analysis should be required to ensure the reliability of the result. The OZIPR modeling results for five local government districts in the Seoul Metropolitan Area (SMA) in June 2000 were used for the sensitivity analysis. The sensitivity analysis result showed that the modeling result of the SMA being VOC-limited region be still valid for a wide range of input parameters' variation. The estimated ozone concentrations were positively related with the initial VOCs concentrations while were negatively related with the initial NOx concentrations. But, the degree of the variations at each local district was different suggesting area specific characteristics being also important. Among the five local governments, Suwon was chosen to identify other variance through the period from April to September in 2000. The monthly modeling results show different ozone values, but still showing the characteristics of VOCs-limited region. Limitations due to not considering long range transport and transfer from neighbor area, limitation of input data, error between observed data and estimated data are all discussed.

• 고문화
• /
• 52호
• /
• pp.123-133
• /
• 1998

The extraction of carbon from temper in organic-tempered pottery of the Initial Neolithic sites on the Russian Far East allowed to date directly the earliest pottery in the area. First results show that pottery of the Gromatukha culture has $^{14}C$<

• 한국농공학회지
• /
• 제26권3호
• /
• pp.59-67
• /
• 1984

This study was carried out to find physical and mechanical properties of soil in Yongsan project area to support basic data for tidalland reclamation. The main results are as follows. 1. Most of the soils in this area consist of clay and silt, and inorganic materials. 2. Natural moisture contents are ranged from 42.2% to 92.9% initial void ratio, from 1.4 to 2.3 Therefore it takes a longtime in Settlement of considerable depth. 3. Wet unit weights decrease with increasing of the nataral moistare contents as rt=2. 005-0. 0065wn.4. The relationships between compression index. and liquid limit, initial void ratio and natural moisture contents are found as follows respectively. Cc =0. 046+0. O12LL Cc=-0. 068+0.367eo Cc =0. 056+0. OO8Wn 5. Natural moisture content, plastic limit, plastic index, initial void ratio and liquid :limit are directly proportional to clay content ratio. The relationships are found as Wn=26. 083+0. 797Cy PL=14. 223+0. 128Cy P1=0. 457+0. 492Cy eo=0. 757+0. O2Ocy LL=14. 695+0. 620Cy. 6. Initial void ratio and liquid limit are directly proportional to natural moisture con-tent as follows. eo=0. 310+0.022wn LL=6. 275+0.592wn

• 한국실내디자인학회논문집
• /
• 제25권2호
• /
• pp.30-40
• /
• 2016

This study analyzed the attention concentration tendencies of one(1) subject who showed convergent exploratory acts actively through the gaze-brainwave measurement experiment of cafe space images and our research findings are as follows. First, the areas of interest (AOIs) that the subject gazed visually by paying attention to it and concentrating on it at a cafe space include counter&menu area, sign area, partition area, image wall area, stairs area, and movable furniture area, and built-in furniture area: seven areas in total. Second, conscious gaze frequency appeared the highest in counter&menu area, and conscious gaze appeared more later than in initial times. Third, conscious gaze pattern was divided into the zone that explored various areas dispersely (distributed exploratory zone) and the zone that explored between particular areas concentratedly (intensive exploratory zone). Fourth, as a result of analyzing the brainwave attention concentration, it was found that the attention concentration in prefrontal lobe (Fp1, Fp2) and frontal lobe (F3, F4) rose to a higher level in the zone of 15 to 16 seconds and this time zone was considered to be a zone where gazing at counter&menu area was very active. In addition, the attention concentration appeared higher in the initial zone than in the later zone, among the entire experimental time zones. Finally, as a result of analyzing the changes in activation by brain portion of the SMR wave expressed when maintaining the arousal and attention concentration, it was found that the right prefrontal lobe and the frontal lobe became activated in the time zone when the intensive exploration of "counter&menu area" and "movable furniture${\leftrightarrow}$built-in furniture area" had occurred and the time zone when the intensive exploration of "image wall${\leftrightarrow}$partition area" and "counter&menu${\leftrightarrow}$sign area" had occurred.

• 소성∙가공
• /
• 제23권3호
• /
• pp.159-163
• /
• 2014

In the current study, the effect of small surface defects in the starting material including roughness, indentations, or scratches, which are perpendicular to the direction of drawing, on the product quality is investigated using the finite element method. An axisymmetric defect is assumed. Such defects are defined by a cylindrical defect area and two tapered regions connecting the defect area to the non-defective area of the material. Various conditions for these initial surface defects are considered, including defect depth, defect slope and defect length. To describe the plastic deformation of the defect in detail during the simulation, local remeshing is applied. Based on the finite element results, defect disappearance maps were generated. It was found that defect disappearance is significantly dependent on the defect depth and the defect length coupled with the defect slope.