• 지질공학
• /
• 제18권4호
• /
• pp.567-576
• /
• 2008

강우에 의한 풍화토층의 침투 특성은 함수비 변화에 따른 침윤선 거동으로부터 파악이 가능하다. 토층내 침투수에 의한 침윤선 형성은 흙매질의 밀도와 입도분포 특성 및 투수계수와도 밀접한 관계를 갖고 있으며, 침윤선의 침투속도는 토층의 투수계수와 거의 동일한 개념으로 볼 수 있다. 이 연구에서는 편마암 분포지역의 산사태 현장모니터링 시스템을 이용하여 표토층을 기준으로 50 cm 및 80 cm 깊이에 대한 토층내 체적함수비 변화로부터 각각의 침투속도를 현장 스케일에서 산정하였으며, 이 지역 토층의 불교란 시료를 채취한 후 실내시험을 통해 구한 투수계수와 비교하였다. 불교란 시료의 투수계수는 $3.15{\times}10^{-3}cm/sec$이며, 체적함수비 변화로 계산된 침투속도는 평균 $1.87{\times}10^{-3}cm/sec$로써 두 배 가량 낮게 나타났다. 그 이유는 현장에서의 침투속도는 매질의 공극과 입도분포에 민감하게 영향을 받기 때문에 실내실험을 통해 산정된 값보다는 다소 낮은 값을 갖기 때문으로 판단된다. 표토층의 체적함수비 및 침투속도에 영향을 미치는 강우강도는 산악 지형을 고려해 볼 때, 일평균 20 mm 이상의 강우가 발생하였을 경우에 토층의 침윤선 범위를 확대시키는 것으로 나타났다.

• Advanced Composite Materials
• /
• 제18권4호
• /
• pp.381-394
• /
• 2009

The kinetics of centrifugal infiltration of fibrous tubular preform is built theoretically, and simulations are conducted to study the effects of various casting conditions on infiltration kinetics and macrosegregation by combining with the energy, mass and kinetic equations. A similarity way is used to simplify the one-dimensional model and the parameter is ascertained by an iterative method. The results indicate that the increase of superheat, initial preform temperature, porosity tends to enlarge the remelting region and decrease copper solute concentration at the infiltration front. Higher angular velocity leads to smaller remelting region and solute concentration at the tip. The pressure in the infiltrated region increase significantly when the angular velocity is much higher, which requires a stronger preform. It is observed that the pressure distribution is mainly determined by the angular velocity, and the macrosegregation in the centrifugal casting is greatly dependent on the superheat of inlet metal matrix, initial temperature and porosity of the preform, and the angular velocity.

• 한국해양공학회지
• /
• 제17권1호
• /
• pp.55-60
• /
• 2003

The effect of size and volume fraction of ceramic particles, with sliding velocity on the wear properties were investigated for the metal matrix composites fabricated by the pressureless infiltration process. The metal matrix composites exhibited about 5.5 - 6 times the wear resistance compared with AC8A alloy at high sliding velocity, and by increasing the particle size and decreasing the volume fraction, the wear resistance was improved. The wear resistance of metal matrix composites and AC8A alloy exhibited different aspects. Wear loss of AC8A alloy increased with sliding velocity, linearly : whereas, metal matrix composites indicated more wear loss than AC8A alloy at the slow velocity region. However, a transition point of wear loss was found at the middle velocity region, which shows the minimum wear loss. Further, wear loss at the high velocity region exhibited nearly the same value as the slow velocity region. In terms of wear mechanism, the metal matrix composites generally exhibited abrasive wear at slow to high sliding velocity； however, AC8A alloy showed abrasive wear at low sliding velocity and adhesive and melt wear at high sliding velocity.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 추계학술대회 논문집
• /
• pp.379-384
• /
• 2002

The effect of size and volume fraction of ceramic particles with sliding velocity on the wear properties were investigated for the metal matrix composites fabricated by pressureless infiltration process. The particulate metal matrix composites exhibited about 5.5 - 6 times of excellent wear resistance compared with AC8A alloy at high sliding velocity, and as increasing the particle size and decreasing the volume fraction the wear resistance was improved. The wear resistance of metal matrix composites and AC8A alloy exhibited different aspects. Wear loss of AC8A alloy increased with sliding velocity linearly. whereas metal matrix composites indicated more wear loss than AC8A alloy at slow velocity region, however a transition point of wear loss was found at middle velocity region which show the minimum wear loss, and wear loss at high velocity region exhibited nearly same value with slow velocity region. In terms of wear mechanism, the metal matrix composites exhibited the abrasive wear at slow to high sliding velocity generally, however AC8A alloy showed abrasive wear at low sliding velocity and adhesive and melt wear at high sliding velocity.

• Geomechanics and Engineering
• /
• 제22권2호
• /
• pp.153-163
• /
• 2020

Laboratory experiments were conducted with two different soil conditions to investigate rainfall infiltration characteristics. The soil layer materials that were tested were weathered granite soil and weathered gneiss soil. Artificial rainfall of 80 mm/hr was reproduced through the use of a rainfall device, and the volumetric water content and matric suction were measured. In the case of the granite soil, the saturation velocity and the moving direction of the wetting front were fast and upward, respectively, whereas in the case of the weathered gneiss soil, the velocity and direction were slow and downward, respectively. Rainfall penetrated and saturated from the bottom to the top as the hydraulic conductivity of the granite soil was higher than the infiltration capacity of the artificial rainfall. In contrast, as the hydraulic conductivity of the gneiss soil was lower than the infiltration capacity of the rainfall, ponding occurred on the surface: part of the rainfall first infiltrated, with the remaining rainfall subsequently flowing out. The unsaturated hydraulic conductivity function of weathered soils was determined and analyzed with matric suction and the effective degree of saturation.

• 상하수도학회지
• /
• 제23권6호
• /
• pp.735-741
• /
• 2009

This study intends to evaluate the efficiency of non-point source reduction technique by using the porous lightweight and recycled aggregate which microorganism is seeded. In case of infiltration velocity 30~70 mm/hr in high concentration of influent, it is indicated that SS was 40~94%, COD 44~91%, BOD 4~91%, TN 1.2~66%, TP 7~70% of removal efficiency. Removal efficiency is good in infiltration velocity 30 > 50 > 70㎜/hr order. Therefore, the non-point source treatment facility filled with lightweight and recycled aggregate using microbial seeding shows higher removal efficiency than a conventional sand and gravel. We confirm that the function and efficiency are improved significantly and applied to treat non-point sources.

• 한국주조공학회지
• /
• 제16권6호
• /
• pp.523-536
• /
• 1996

This paper relates to fabrication processing analysis of metal matrix composites by the injection of liquid metal into a fibrous preforms. One dimensional heat transfer analysis during squeeze infiltration process of aluminum base composites has been studied. An analysis method was investigated for the temperature distribution, infiltration velocity and melt infiltration characteristics with the commercial preform with short fiber array. When molten metal is infiltrated in a fibrous preform with random orientation, phase transformation will be occurred in a region such as molten metal, solidified region, preform region and infiltration composites region. a mathematical modelling for a solidification phenomena in fabrication process of metal matrix composites using a squeeze infiltration technique was investigated by the basic relations for liquid metal into a fibrous preform. The temperature distribution of theoretical results was compared with experimental data.

• 지질공학
• /
• 제21권1호
• /
• pp.25-34
• /
• 2011

본 연구에서는 도로시공을 위한 사면절개시 발생된 산사태 현장을 대상으로 강우시 침투를 고려한 사면안정해석 방법을 적용하였다. 강우시 침투를 고려한 사면안정해석법은 크게 세가지로 구분할 수 있다. 첫 번째는 지반내 습윤전선이 하강을 고려하여 해석하는 방법, 두 번째는 지반내 지하수위의 상승을 고려하여 해석하는 방법, 그리고 세 번째는 지반내 습윤전선 하강 및 지하수위 상승을 고려하여 해석하는 방법이다. Bishop의 간편법을 이용하여 해석한 결과, 강우시 습윤전선 하강으로 인한 사면안전율 감소가 지하수위 상승으로 인한 사면안전율 감소보다 빠르게 진행됨을 알 수 있다. 또한, 습윤전선 하강 및 지하수위 상승이 동시에 일어날 경우 사면안전율은 매우 급속하게 감소함을 알 수 있다. 따라서, 강우시 사면안정해석법은 지반내 지하수위 상승과 습윤전선 하강을 동시에 고려하여 해석하는 것이 보다 바람직하다.

• 물과 미래
• /
• 제8권2호
• /
• pp.56-60
• /
• 1975

Traditional descriptions of water movement in soils and of calculations of infiltration rates neglect the air movement and its compressibility. The movement of two fluids in the bounded layered porous medium is treated analytically and computer simulations are conducted for given boundary conditions and initial saturation profiles. The movement of a given saturation across the interface between the different soil layers is theoretically developed by considering the conservation of mass. It is shown that the existence of the interface affects the infiltration rate when the average total velocity is greater than zero. The transition from one layer to another layer cause a change in the capillary drive and consequently influences the infiltration rate.

• 한국지반공학회논문집
• /
• 제28권2호
• /
• pp.71-78
• /
• 2012

본 연구에서는 실내 강우침투실험을 통하여 강우강도에 따른 지반 내 침투속도를 산정하였으며, 침투특성을 분석하여 보았다. 또한 수치해석을 이용한 해석결과와 비교 검증을 수행하였으며, 시간에 따른 간극수압과 포화도 그리고 유출속도의 변화는 대체로 잘 일치함을 보였다. 강우강도에 따른 침투속도는 실내실험과 수치해석에서 선형적으로 증가하는 경향을 나타냈으며, 강우강도가 지반의 포화투수계수에 근접시 침투속도가 급격히 증가하였다. 또한 강우 침투시 습윤전선의 상부는 부분적으로 포화되어 침투하는 경향을 보였다. 따라서 실제 지반에서 습윤전선은 비교적 빠르게 진행하여 사면의 불안정을 초래할 것으로 판단된다.