• 대한의용생체공학회:의공학회지
• /
• 제35권3호
• /
• pp.35-41
• /
• 2014

In this study, joint angles of the lower extremity and inertial sensor data such as accelerations and angular velocities were measured during a ski simulator exercise in order to evaluate the skill of skiers. Twenty experts and twenty unskilled skiers were recruited for the study. All expert skiers held the certificates issued by the Korea Ski Instructors Association. A three-dimensional motion capture system and two inertial sensors were used to acquire joint movements, heel acceleration and heel angular velocity during ski simulator exercises. Pattern variation values were calculated to assess the variations in ski simulator motion of expert and unskilled skiers. Integral ratio of roll angular velocity was calculated to determine the parallel alignment of the two feet. Results showed that ski experts showed greater range of motion of joint angle, peak-to-peak amplitude(PPA) of heel acceleration and PPA of heel angular velocity than unskilled skiers. Ski experts showed smaller pattern variations than unskilled skiers. In addition, the integral ratio of roll angular velocity in ski experts was closer to 1. Inertial sensor data measurements during the ski simulator exercises could be useful to evaluate the skill of the skier.

• Journal of Positioning, Navigation, and Timing
• /
• 제9권3호
• /
• pp.273-284
• /
• 2020

The performance of Global Navigation Satellite System (GNSS) chipset and Inertial Measurement Unit (IMU) sensors embedded in smartphones for location-based services (LBS) is limited due to the economic reasons for their mass production. Therefore, it is necessary to efficiently process the output data of the smartphone's embedded sensors in order to derive the optimum navigation values and, as a previous step, output performance of smartphone embedded sensors needs to be verified. This paper analyzes the navigation performance of such devices by processing the raw measurements data output from smartphones. For this, up-to-dated versions of smartphones provided by Samsung (Galaxy s10e) and Xiaomi (Mi 8) are used in the test experiment to compare their performances and characteristics. The GNSS and IMU data are extracted and saved by using an open market application software (Geo++ RINEX Logger & Mobile MATLAB), and then analyzed in post-processing manner. For GNSS chipset, data is extracted from static environments and verified the position, Carrier-to-Noise (C/N₀), Radio Frequency Interference (RFI) performance. For IMU sensor, the validity of navigation and various location-based-services is predicted by extracting, storing and analyzing data in static and dynamic environments.

• 전기학회논문지
• /
• 제68권1호
• /
• pp.189-198
• /
• 2019

In recent years, visual-inertial odometry(VIO) algorithms have been extensively studied for the indoor/urban environments because it is more robust to dynamic scenes and environment changes. In this paper, we propose loosely coupled(LC) VIO algorithm that utilizes the velocity vectors from both visual odometry(VO) and inertial measurement unit(IMU) as a filter measurement of Extended Kalman filter. Our approach improves the estimation performance of a filter without adding extra sensors while maintaining simple integration framework, which treats VO as a black box. For the VO algorithm, we employed a fundamental part of the ORB-SLAM, which uses ORB features. We performed an outdoor experiment using an RGB-D camera to evaluate the accuracy of the presented algorithm. Also, we evaluated our algorithm with the public dataset to compare with other visual navigation systems.

• 제어로봇시스템학회논문지
• /
• 제18권7호
• /
• pp.632-637
• /
• 2012

This paper introduces a simple and efficient calibration method for three-axis accelerometers and three-axis gyroscopes using three-axis motion rate table. Usually, the performance of low cost MEMS-based inertial sensors is affected by scale and bias errors significantly. The calibration of these errors is a bothersome problem, but the previous calibration methods cannot propose simple and efficient method to calibrate the errors of three-axis inertial sensors. This paper introduces a new simple and efficient method for the calibration of accelerometer and gyroscope. By using a three-axis motion rate table, this method can calibrate the accelerometer and gyroscope simultaneously and simply. Experimental results confirm the performance of the proposed method.

• 센서학회지
• /
• 제29권4호
• /
• pp.237-242
• /
• 2020

This paper deals with relative position estimation using a Kalman filter (KF) based on inertial sensors that have been widely used in various biomechanics-related outdoor applications. In previous studies, the relative position is determined using relative orientation and predetermined segment-to-joint (S2J) vectors, which are assumed to be constant. However, because body segments are influenced by soft tissue artifacts (STAs), including the deformation and sliding of the skin over the underlying bone structures, they are not constant, resulting in significant errors during relative position estimation. In this study, relative position estimation was performed using a KF, where the S2J vectors were adopted as time-varying states. The joint constraint and the variations of the S2J vectors were used to develop a measurement model of the proposed KF. Accordingly, the covariance matrix corresponding to the variations of the S2J vectors continuously changed within the ranges of the STA-causing flexion angles. The experimental results of the knee flexion tests showed that the proposed KF decreased the estimation errors in the longitudinal and lateral directions by 8.86 and 17.89 mm, respectively, compared with a conventional approach based on the application of constant S2J vectors.

• Journal of Mechanical Science and Technology
• /
• 제17권5호
• /
• pp.629-636
• /
• 2003

This paper introduces the developed geometry PIG (Pipeline Inspection Gauge), one of several ILI (In-Line Inspection) tools, which provide a full picture of the pipeline from only single pass, and has compact size of the electronic device with not only low power consumption but also rapid response of sensors such as calipers, IMU and odometer. This tool is equipped with the several sensor systems. Caliper sensors measure the pipeline internal diameter, ovality and dent size and shape with high accuracy. The IMU (Inertial Measurement Unit) measures the precise trajectory of the PIG during its traverse of the pipeline. The IMU also provide three-dimensional coordination in space from measurement of inertial acceleration and angular rate. Three odometers mounted on the PIG body provide the distance moved along the line and instantaneous velocity during the PIG run. The datum measured by the sensor systems are stored in on-board solid state memory and magnetic tape devices. There is an electromagnetic transmitter at the back end of the tool, the transmitter enables the inspection operators to keep tracking the tool while it travels through the pipeline. An experiment was fulfilled in pull-rig facility and was adopted from Incheon LT (LNG Terminal) to Namdong GS (Governor Station) line, 13 km length.

• 한국콘텐츠학회논문지
• /
• 제10권4호
• /
• pp.115-122
• /
• 2010

현재 제공되고 있는 지능화된 서비스들은 사용자의 위치를 기반으로 동작한다. 실내 위치 측정 서비스를 위한 수많은 장비들은 각각의 특징된 동작과 운영체계를 가지므로 다양한 기기들을 연결하고 제어할 수 있는 미들웨어의 상호 운용성과 다양성이 필요하다. 기존 관성 센서를 이용한 실내 위치추정 방법은 공간 크기에 따른 추가 비용이 발생하여 상대적인 효율성이 떨어진다. 따라서 본 논문에서 제안하는 실내 사용자 위치추정 방법은 오픈소스 프로젝트인 OSGi 프레임워크를 이용하여 통합서비스를 지원하고, 초음파 센서를 이용하여 특정 물체와의 정확한 근접 거리를 통해 관성 센서의 문제점을 보완하였으며, 신뢰도의 항목을 추가하여 반응속도 차이에 따른 오차율을 줄였다.

• 반도체디스플레이기술학회지
• /
• 제22권3호
• /
• pp.62-66
• /
• 2023

With the advancement in technology and rapid increase in the demand for microelectromechanical systems (MEMS) based inertial measurement units (IMUs), high-volume production and test system remain a major challenge for the MEMS industry. To compete with the challenging market of Industry 4.0, here we developed an automatic test system to evaluate the performance of the ovenized IMU sensors as well as analyze the data. The automatic test system was developed by interfacing a commercial MEMS IMU (BMI 088) using LabVIEW. The BMI 088 was tested experimentally for long-term bias stability, ON/OFF bias repeatability, and root mean square (rms) noise. Furthermore, the data was analyzed through the developed test system. The results show that the automatic test system has improved the test time and reduced human effort. The developed automatic test system is a significant approach to MEMS research and development (R&D) to increase and improve the mass production of IMUs.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.116.5-116
• /
• 2001

When inertial navigation system(INS) employ more sensors that mutually orthogonal sets to three, the redundant sensor system can have improved reliability and accuracy. For the redundant system the placement of redundant sensors is related to the system performance and also the number and proper orientation of sensors are important. We consider INS sensor configurations using two IMUs comprised mutually orthogonal sets of three. We suggest several configurations using two IMUs and analyze the system performance and the FDI(fault detection and isolation) properties from suggested configurations.

• 제어로봇시스템학회논문지
• /
• 제10권4호
• /
• pp.364-370
• /
• 2004

In this paper, we propose a FDI method, which comes from singular value decomposition of measurement matrix fur redundant sensors. We analyze the performance of the proposed FDI method by comparing with the GLT method in two ways such as FDI performance and GN＆C performance. Also, we propose a GN＆C performance index by combining FDI and GN＆C performance.