• International Journal of Automotive Technology
• /
• 제8권2호
• /
• pp.233-241
• /
• 2007

A lumped parameter model is proposed for the analysis of dynamic behaviour of a Passive Hydraulic Engine Mount (PHEM), incorporating inertia track and throttle, which is characterized by effective and efficient vibration isolation behaviour in the range of both low and high frequencies. Most of the model parameters, including volume compliance of the throttle chamber, effective piston area, fluid inertia and resistance of inertia track and throttle are identified by an experimental approach. Numerical predictions are obtained through a finite element method for responses of dynamic stiffness of the rubber spring. The experiments are made for the purpose of PHEM validation. Comparison of numerical results with experimental observations has shown that the present PHEM achieves good performance for vibration isolation.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2000년도 전력전자학술대회 논문집
• /
• pp.199-202
• /
• 2000

The accurate identification of the motor parameters in crucially important to achieve high dynamic performance of induction motors. In this paper parameter auto-tuning algorithms for stator(rotor) resistance stator(rotor) leakage inductance mutual inductance and rotor inertia. Stator(rotor) resistance and stator(rotor) leakage inductance are identified based on the stationary coordinate and mutual inductance and rotor resistor on the scalar speed control and the transient motor terminal voltage. To demonstrate the practical significance of our results we present some experimented results.

• 전력전자학회논문지
• /
• 제7권1호
• /
• pp.74-80
• /
• 2002

철도차량용 추진시스템은 안전성과 신뢰성 때문에 성능을 평가해야만 한다. 일반적으로 Flywheel Type시험방법은 시험설비로 널리 사용되고 있다 그러나 Flywheel에 의해 생기는 기계적 관성은 변하기 어렵고 실제적인 주행저항을 표현할 수 없다. 본 연구는 다양한 차량부하의 개발에 초점을 두고 수행되었다. 그렇기 때문에 실제적인 차량 부하 특성을 얻기 위해 벡터모터에 의해 제어되는 다양한 차량부하를 사용하는 방법을 제안하였고 컴퓨터 시뮬레이션을 통해 결과를 확인하였다.

• Journal of Power Electronics
• /
• 제10권6호
• /
• pp.749-761
• /
• 2010

The switching frequency of a power device is a very important parameter in the design of a parallel active power filter (PAPF), but so far, very little discussion has been conducted on it in a quantitative manner in previous publications. In this paper, an extensive analysis on the effects of the switching frequency on the performance of a PAPF is made, and a specification of the switching frequency values with different compensation results is presented. A first-order inertia element and a second-order oscillation element are considered as approximate models of a PAPF, respectively. The compensation characteristic for each order of harmonic current is obtained at different switching frequencies. Then, the THDs of each model for the system loads of a rectifier with resistance and inductance loads are proposed. The compensation results of a PAPF controlled as a first-order inertia element are better than those of a PAPF controlled as a second-order oscillation element. With two types of system loads which are rectifier with resistance and inductance loads and rectifier with resistance, inductance and capacitance loads, the THDs of the source current after compensation are presented with different switching frequencies. The compensation characteristics for the most widely used digital control system are investigated. The situation with an analog control is the theoretical characteristic and it is the best situation. The compensation characteristic of the digital control is worse than the compensation characteristic of the theoretical characteristic. Based on these analyses, the specifications of compensation characteristics with different switching frequencies are quite straightforward. Finally, a practical design example is studied to verify the application.

• 조명전기설비학회논문지
• /
• 제30권3호
• /
• pp.73-78
• /
• 2016

3phase induction motor consumes 40% of national electric power. so It is one of the most important electric device for the national power policy. The efficiency measurement is carried out by IEC standards. After the temperature rise test, It's difficult to measure the winding resistance immediately. because of inertia and power cut-off time. Therefore, IEC standards suggest the measurement time. But during the measurement time, the winding temperature cools down. It causes the value of winding resistance is variable. Several conditions which possibly occurred by the measurement time of IEC 60034-1 are suggested. and The efficiency evaluation of 3phase induction motors is carried out by IEC 60034-2-1 with the several conditions. As the results, we find out the winding resistance rapidly goes down within 15 sec. so It proves that the winding resistance should be measured within 15 sec. for the efficiency evaluating of 3phase induction motor.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2003년도 춘계학술대회 논문집
• /
• pp.37-42
• /
• 2003

Fundamental Study for optimizing ship hull form using SQP(sequential quadratic programming) method in a resistance point of view is presented. The Wigley hull is used as an initial hull and numerical calculations are carried out according to various froude numbers. To obtain the ship resistance the wave resistance is evaluated by a Rankine source panel method with nonlinear free surface conditions and the ITTC 1957 friction line is used to predict the frictional resistance coefficient. The geometry of a hull surface is represented and modified by B-spline surface patch. The displacement and the waterplane transverse 2nd moment of inertia of the hull is fixed during the optimization process. And the shp design program called EzHULL is used to draw the lines of the optimized hull form to perform the model test.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 학술회의 논문집 정보 및 제어부문 B
• /
• pp.452-455
• /
• 2003

Based on a field-oriented model of induction motor, adaptive backstepping approach using neural network(RBFN) is proposed for the control of induction motor in this paper. In order to achieve the speed regulation with the consideration of avoiding singularity and improving power efficiency, rotor angular speed and flux amplitude tracking objectives are formulated. rotor resistance uncertainty is compensated by adaptive backstepping and mechanical lumped uncertainty such as load torque disturbance, inertia moment, friction by RBFN. Simulation is provided to verify the effectiveness of the proposed approach.

• 전력전자학회논문지
• /
• 제6권3호
• /
• pp.282-290
• /
• 2001

유도전동기의 고성능 응답을 얻기 위해서는 전동기 매개변수의 정확한 추정이 필수적이다. 본 논문에서는 고정자(회전자)저항, 고정자(회전자)누설 인덕턴스, 상호 인덕턴스, 관성 모멘트와 같은 매개변수들을 오프라인으로 측정하였다. 고정자(회전자) 저항과 고정자(회전자) 누설 인덕턴스는 정지좌표계의 방정식들로부터 측정한 반면, 상호 인덕턴스는 스칼라 제어 상태에서 측정되었다. 마지막으로, 확장 칼만필터를 이용하여 회전자 역시 상수를 온라인 상에서 동정하였다. 본 논문에서 언급하는 추정알고리즘들의 유용성을 보이기 위해 실험결과들을 제시하였다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 추계학술발표대회 논문집
• /
• pp.198-201
• /
• 2002

It has been well-blown that sandwich structures are efficient to resist bending loads by increasing the moment of inertia of the panel. However, the accurate theoretical prediction of failure load and its optimization of sandwich beams for strength under concentrated loads were so complicated. Moreover, the appropriate selection of the variables, such as face thickness, core density and core thickness of the sandwich beam with many theories has continuously researched to satisfy for the given strength to weight structural requirement. There will be interesting to investigate the effect of those variables with its optimization for the load resistance.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1987년도 정기총회 및 창립40주년기념 학술대회 학회본부
• /
• pp.25-28
• /
• 1987

Design procedure of adaptive controller with variable load condition is present and applied to velocity control of small, permanent magnet DC servo motor. The state feedback control scheme is adopted and Recursive Least Squares algorithm is used for parameter estimation. In order to reduce the time consuming. In the procedure of adaptation-gain tuning of state feedback controller, approximate curve fitting technique is applied to the relations between load condition and poles of the system, load condition and feedback gains. With this method, fast adaptation can be accomplished. It is shown that this procedure can be applied not only to variable load condition but also to variation of other system constants, for example variation of resistance and inductance etc.. Simulation results is present for both cases - variable inertia load, variable motor resistance to verify performance improvements. This design procedure produces an adaptive con troller which is feasible for implementation with microprocessor by reducing calculation time.