• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2004년도 춘계 학술발표회 제16권1호
• /
• pp.498-501
• /
• 2004

A new slab design using secant stiffness, Direct Inelastic Slab Design, was developed. Since basically the proposed design method uses linear analysis, it is convenient and stable in numerical analysis. At the same time, the proposed design method can accurately estimate the inelastic strength and ductility demands of slab because it can analyzes the inelastic behavior of structure using iterative calculations for secant stiffness. In the present study, the procedure of the proposed design method was established, and a computer program incorporating the proposed method was developed. Design examples using the proposed method were presented, and compared with traditional nonlinear analysis, and experiments. The Direct Inelastic Slab Design, as an integrated analysis/design method, can directly address the design strategy intended by the engineer, such as moment strength and ductility limit. As a result, economical and safe design can be achieved.

• Structural Engineering and Mechanics
• /
• 제48권2호
• /
• pp.275-289
• /
• 2013

The cross sections of multi-span beams are sometimes suddenly increased at the interior support of continuous beams to resist high negative moment. An earlier study on elastic lateral torsional buckling of stepped beams was conducted to propose new design equations. This research aims to continue the earlier study by considering the effect of inelastic buckling of stepped beams subjected to pure bending and general loading condition. A three-dimensional finite element-program ABAQUS and a statistical program MINITAB were used in the development of new design equations. The inelastic lateral torsional buckling strengths of 36 and 27 models for singly and doubly stepped beams, respectively, were investigated. The general loading condition consists of 15 loading cases based on the number of inflection point within the unbraced length of the stepped beams. The combined effects of residual stresses and geometrical imperfection were also considered to evaluate the inelastic buckling strengths. The proposed equations in this study will definitely improve current design methods for the inelastic lateral-torsional buckling of stepped beams and will increase efficiency in building and bridge design.

• Structural Engineering and Mechanics
• /
• 제42권5호
• /
• pp.631-644
• /
• 2012

Current seismic codes require from the seismically designed structures to be capable to withstand inelastic deformation. Many studies dealt with the development of different inelastic spectra with the aim to simplify the evaluation of inelastic deformation and performance of structures. Recently, the concept of inelastic spectra has been adopted in the global scheme of the performance-based seismic design through capacity-spectrum methods. In this paper, the median of the ductility demand ratio for 80 ground motions are presented for different levels of normalized yield strength, defined as the yield strength coefficient divided by the peak ground acceleration (PGA). The influence of the post-to-preyield stiffness ratio on the ductility demand is investigated. For fixed levels of normalized yield strength, the median ductility versus period plots demonstrated that they are independent of the earthquake magnitude and epicentral distance. Determined by regression analysis of the data, two design equations have been developed; one for the ductility demand as function of period, post-to-preyield stiffness ratio, and normalized yield strength, and the other for the inelastic deformation as function of period and peak ground acceleration valid for periods longer than 0.6 seconds. The equations are useful in estimating the ductility and inelastic deformation demands for structures in the preliminary design. It was found that the post-to-preyield stiffness has a negligible effect on the ductility factor if the yield strength coefficient is greater than the PGA of the design ground motion normalized by gravity.

• 한국강구조학회 논문집
• /
• 제16권2호통권69호
• /
• pp.181-190
• /
• 2004

본 연구소에서는 할선강성을 사용하여 비탄성 해석 및 설계를 수행하는 새로운 설계방법을 개발하였다. 개발한 설계법은 선형해석을 수행하므로 수치해석이 안정성과 용이성을 갖추고 있으며, 동시에 반복계산으로 구조물의 비탄성 거동을 해석하므로 각 부재의 비탄성 강도 및 연성 요구량을 정확히 예측할 수 있다. 본 연구에서는 제안된 설계법의 절차를 성립하였고, 이를 고려한 컴퓨터 해석/설계 프로그램을 개발하였다. 또한, 제안된 설계법을 사용한 설계예제를 제시하였으며, 기존의 탄성 및 소성설계법과의 비교를 통하여 그 우수성을 입증하였다. 기존의 비선형설계방법은 일반적으로 초기 설계를 수행하고 비선형해석을 이용하여 초기설계안을 검증하는데 비하여, 제안된 방법은 반복계산을 통하여 비탄성해석과 설계를 동시에 수행하므로 각 부재의 비탄성 강도 및 연성 요구량을 직접적으로 계산할 수 있다. 또한 설계자의 의도에 따라 부재 강도 및 연성능력의 제한, 강기둥-약보 등의 비선형 설계전략을 효과적으로 구현하므로, 경제적이고 안전한 설계가 가능하다.

• 콘크리트학회논문집
• /
• 제20권3호
• /
• pp.345-356
• /
• 2008

선행 연구에서는 할선강성에 대한 선형해석을 수행함으로써 편리하게 비탄성 설계를 할 수 있는 직접 비탄성 스트럿-타이 모델이 개발되었다. 본 연구에서는 기존 직접 비탄성 스트럿-타이 모델을 개선하여, 반복계산 없이 할선강성에 대한 한번의 선형해석으로 철근콘크리트 부재의 비탄성 설계를 수행할 수 있는 간략화된 직접 비탄성 스트럿-타이 모델 (simplified direct inelastic strut-and-tie model, 이하 S-DISTM)을 개발하였다. S-DISTM은 철근콘크리트 부재를 콘크리트 압축 스트럿과 철근 인장 타이로 모델링한다. 스트럿과 타이 요소는 설계자의 설계 전략에 따라 탄성강성 또는 할선강성의 선형 재료 모델을 사용한다. 스트럿과 타이 요소의 파괴 기준을 정의하기 위하여 콘크리트 압축파괴 및 철근 인장파단 등을 고려하였다. S-DISTM을 사용하여 깊은보, 연결보, 전단벽 등 다양한 전단지배 철근콘크리트 부재의 비탄성 설계를 수행하였고, 비탄성 설계로 결정된 철근양, 변형 능력 등을 기존 실험 결과와 비교하였다.

• Structural Engineering and Mechanics
• /
• 제12권6호
• /
• pp.573-594
• /
• 2001

A two-level displacement-based design procedure is developed. To obtain the displacement demands, elastic spectra for occasional earthquakes and inelastic spectra for rare earthquakes are used. Minimum global stiffness and strength to be supplied to the structure are based on specified maximum permissible drift limits and on the condition that the structure responds within the elastic range for occasional earthquakes. The performance of the structure may be assessed by an inelastic push-over analysis to the required displacement and the evaluation of damage indices. The approach is applied to the design of a five-story reinforced concrete coupled wall structure located in the most hazardous seismic region of Argentina. The inelastic dynamic response of the structure subjected to real and artificially generated acceleration time histories is also analyzed. Finally, advantages and limitations of the proposed procedure from the conceptual point of view and practical application are discussed.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1999년도 가을 학술발표회 논문집
• /
• pp.214-224
• /
• 1999

The design response spectrum has been widely used in seismic design to estimate force and deformation demands of structures imposed by Earthquake Ground Motion (EQGM). Inelastic Design Response Spectra (IDRS) to specify design yielding strength in seismic codes are obtained by reducing the ordinates of Linear Elastic Design Response Spectrum (LEDRS) by strength reduction factor (R). Since a building is designed using reduced design spectrum (IDRS) rather than LEDRS in current seismic design procedures it allows structures behave inelastically during design level EQGM. Inelastic Response Spectra (IRS) depend not only on the characteristics of the expected ground motion at a given site, but also on the dynamic properties and nonlinear characteristics of a structure. However, it has not been explicitly investigated the effect of different hysteretic models on IRS. In this study, the effect of hysteretic models on IRS is investigated.

• Wind and Structures
• /
• 제31권2호
• /
• pp.153-164
• /
• 2020

In the design of buildings, lateral loading is one of the most important factors considered by structural designers. The concept of performance-based design (PBD) is well developed for seismic load. Whereas, wind design is mainly based on elastic analysis for both serviceability and strength. For tall buildings subject to extreme wind load, inelastic behavior and application of the concept of PBD bear consideration. For seismic design, current practice primarily presumes inelastic behavior of the structure and that energy is dissipated by plastic deformation. However, due to analysis complexity and computational cost, calculations used to predict inelastic behavior are often performed using elastic analysis and a response modification factor (R). Inelastic analysis is optionally performed to check the accuracy of the design. In this paper, a framework for application of an R factor for wind design is proposed. Theoretical background on the application and implementation is provided. Moreover, seismic and wind fatigue issues are explained for the purpose of quantifying the modification factor R for wind design.

• 한국강구조학회 논문집
• /
• 제17권1호통권74호
• /
• pp.103-113
• /
• 2005

본 연구에서는 선행 연구에서 개발된 강구조물에 대한 직접비탄성설계 방법을 설계실무의 활용성을 확대할 수 있도록 개선하였다. 그룹부재에 대한 설계, 불연속적인 단면 성능, 축력에 따른 휨재하능력의 변화, 접합방식에 따른 거동특성, 다중하중조건 및 성능기준 등 강구조물 설계실무의 제한조건을 고려하여 비탄성설계를 수행할 수 있는 방법을 개발하였다. 본 연구에서는 제안된 방법의 해석 및 설계절차를 정립하였고, 이를 적용한 컴퓨터 해석/설계 프로그램을 개발하였다. 전통적인 탄성설계와 제안된 직접비탄성설계법을 사용한 설계결과를 비교하였으며, 기존의 비선형해석프로그램을 이용하여 설계결과를 검증하였다. 비탄성 변형을 고려할 수 있는 제안된 설계법은 전통적인 탄성해석을 사용한 한계상태설계에 비하여 강재량을 절감하고, 구조물의 변형능력을 향상하였다. 제안된 설계방법은 비탄성 거동을 구조물의 설계에 직접 반영할 수 있으므로 설계에 편리하고 각 소성힌지의 변형을 제어함으로써 구조안전성을 확보하고 동시에 변형능력을 최대로 활용하는 설계를 수행할 수 있다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1997년도 가을 학술발표회 논문집
• /
• pp.207-214
• /
• 1997

Current seismic design code is based on the assumption that the designed structures would be behaved inelastically during a severe earthquake ground motion. For this reason, seismic design forces calculated by seismic codes are much lower than the forces generated by design earthquakes which makes structures responding elastically. Present procedures for calculating seismic design forces are based on the use of elastic spectra reduced by a strength reduction factors known as "response modificaion factor". The effect of hysteretic behavior, as well as maximum ductility ratio and period on the inelastic strength demand is investigated. Special emphasis is given to the effects of the hysteretic characteristics such as strength degradation or pinching. Results indicate that inelastic strength demands are strongly dependent on level of inelastic deformation, period and hysteretic behavior.