• Journal of the Korean Ceramic Society
• /
• v.36 no.3
• /
• pp.284-292
• /
• 1999

고체함량을 변화시킨 NiCuZn 페라이트 페이스트를 사용하여 스크린 인쇄법으로 7.7$\times$4.5$\times$1.0 nm 크기의 칩인덕터를 제조한 후, 페라이트 페이스트의 고체함량에 따른 수축률, 소결밀도, 미세구조, 계면반응 등의 물리적 특성 및 자기적 특성 변화를 분석하였다. 조온소결을 위하여 attrition milling 공정을 통하여 미세분말을 준비하였으며, 소결온도는 880~94$0^{\circ}C$로 변화시켰다. 90$0^{\circ}C$에서 2시간 열처리된 페라이트 후막의 소결밀도는 고체함량이 50,55,60%로 증가할수록 5.12,5.14,5.18g/㎤로 증가하였으며, 이에 따라 칩 인덕터 시편들의 주파수 10 MHz에서 L값이 2.1,2.3,2.5 $\mu$H로 커졌다.Q값은 소결밀도 증가에 의한 Q값 증가효과와 아울러 입자가 커짐에 따른 반대효과로 인하여 고체함량에 따라 87,90,94로 큰 변화가 없었다. 페라이트 페이\ulcorner의 고체함량 및 소결온도와 무관하게 Ag 성분의 페라이트 쪽으로의 확산현상은 나타나지 않았다.

• Journal of Power Electronics
• /
• v.9 no.6
• /
• pp.835-844
• /
• 2009

In this paper a new buck-boost type DC-DC converter is presented. Its voltage gain is positive, all active elements operate under soft-switching condition independent of loading, magnetic isolation and self output short-circuit protection exist, and very fast dynamic operation is achievable by a simple bang-bang controller. This converter also exhibits appropriate PFC characteristics since its input current is inherently proportional to the source voltage. When the voltage source is off-line, it is sufficient to add an inductor after the rectifier, then near unity power factor is achievable. All essential guidelines to design the converter as a DC-DC and a PFC regulator are presented. Simulation and experimental results verify the developed theoretical analysis.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.3
• /
• pp.28-34
• /
• 2010

In this paper, the transceiver for RFID reader using 13.56MHz as a carrier frequency and meeting International Standard ISO 14443 type A, 14443 type B and 15693 is presented. The receiver is composed of envelope detector, VGA(Variable Gain Amplifier), filter, comparator to recovery the received signal. The proposed automatic reference voltage generator, positive peak detector, negative peak detector, and data slicer circuit can adjust the decision level of reference voltage over the received signal amplitudes. The transmitter is designed to drive high voltage and current to meet the 15693 specification. By using inductor loading circuit which can swing more than power supply and drive large current even under low impedance condition, it can control modulation rate from 30 percent to 5 percent, 100 perccnt and drive the output currents from 5 mA to 240 mA depending on standards. The 13.56 MHZ RFID reader is implemented in $0.18\;{\mu}m$ CM08 technology at 3.3V single supply. The chip area excluding pads is $1.5mm\;{\times}\;1.5mm$.